3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8608EDC#TRMPBF
Analog Devices · DC-DC Converters · DFN-8-EP(2x2)
LT8608EDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Provides drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC with no series resistor. |
| 2 | SW | output | Output of the internal power switches; connect to the inductor and boost capacitor and keep the node small on the PCB. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin (varies 2.8V to 3.5V, 20mA max output); decouple with at least 1µF low-ESR ceramic and do not load with external circuitry. |
| 4 | RT | passive | A resistor from RT to ground sets the switching frequency (200kHz to 2.2MHz range). |
| 5 | FB | input | Feedback input regulated to 0.778V; connect the feedback resistor divider tap here. |
| 6 | PG | output | Open-drain power-good output that stays low until FB is within ±8.5% of final regulation and no faults exist; valid when VIN is above 3.2V. |
| 7 | VIN | power_in | Supplies the internal circuitry and topside power switch (3.0V to 42V operating range, 42V abs max); must be locally bypassed close to VIN and GND. |
| 8 | EN/UV | input | Shuts down the part when low and enables when high, with 1.05V rising and 1.00V falling thresholds; tie to VIN if unused or use a divider from VIN to set UVLO. |
| 9 | GND | power_in | Exposed pad ground; connect to the negative terminal of the input capacitor and solder to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | VIN(MIN) | 2.5 | 3 | V | over full operating temperature range | 2 | |
| VIN Quiescent Current (shutdown) | IQ | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 2 | |
| VIN Quiescent Current (not switching) | IQ | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8608 DFN, VIN ≤ 36V | 2 | |
| VIN Current in Regulation (100µA load) | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 2 | ||
| VIN Current in Regulation (1mA load) | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA | 2 | ||
| Feedback Reference Voltage DFN | VFB | 0.773 | 0.778 | 0.783 | V | DFN Package, VIN = 6V, ILOAD = 100mA | 3 |
| Feedback Reference Voltage DFN (full temp) | VFB | 0.753 | 0.778 | 0.803 | V | DFN Package, VIN = 6V, ILOAD = 100mA, over full temperature range | 3 |
| Feedback Voltage Line Regulation | 0.02 | 0.06 | %/V | VIN = 4.0V to 40V | 3 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1V | 3 | ||
| Minimum On-Time | tON(MIN) | 35 | 65 | ns | ILOAD = 1A, SYNC = 0V or LT8608 DFN | 3 | |
| Minimum Off Time | tOFF(MIN) | 93 | 130 | ns | 3 | ||
| Oscillator Frequency DFN (RT=221k) | fSW | 130 | 200 | 270 | kHz | RT = 221k, ILOAD = 500mA | 3 |
| Oscillator Frequency DFN (RT=60.4k) | fSW | 610 | 700 | 790 | kHz | RT = 60.4k, ILOAD = 500mA | 3 |
| Oscillator Frequency DFN (RT=18.2k) | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 200mA | 3 |
| Top Power NMOS On-Resistance | RDS(ON) | 350 | mΩ | ILOAD = 0.5A | 3 | ||
| Top Power NMOS Current Limit | ILIM | 2.1 | 2.9 | 3.9 | A | 3 | |
| Bottom Power NMOS On-Resistance | RDS(ON) | 230 | mΩ | 3 | |||
| SW Leakage Current | 15 | µA | VIN = 36V | 3 | |||
| EN/UV Pin Threshold | 0.99 | 1.05 | 1.11 | V | EN/UV Rising | 3 | |
| EN/UV Pin Hysteresis | 50 | mV | 3 | ||||
| EN/UV Pin Current | -20 | 20 | nA | VEN/UV = 2V | 3 | ||
| PG Upper Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Rising | 3 | |
| PG Lower Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Falling | 3 | |
| PG Hysteresis | 0.5 | % | 3 | ||||
| PG Leakage | -200 | 200 | nA | VPG = 42V | 3 | ||
| PG Pull-Down Resistance | 550 | 1200 | Ω | VPG = 0.1V | 3 | ||
| VIN, EN/UV, PG Voltage | 42 | V | 2 | ||||
| FB Voltage | 4 | V | FB, TR/SS | 2 | |||
| Operating Junction Temperature Range LT8608E | TJ | -40 | 125 | °C | LT8608E | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 |
CAD (KiCad official)
- Symbol:
LT8608EDC#TRMPBF - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
lt8608edc-trmpbf-etched.step/lt8608edc-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8608edc-trmpbf.step/lt8608edc-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
ef5ca800fd4c6a67, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).