3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8210IUJ#TRPBF
Analog Devices · DC-DC Controllers · QFN-40-EP(6x6)
LT8210IUJ#TRPBF from Analog Devices, in a QFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC/SPRD | input | External clock synchronization input accepting 80kHz to 400kHz; tie to VDD for spread-spectrum operation or to ground otherwise. |
| 2 | PWGD | output | Open-drain power-good output pulled low when the output is outside ±10% of its programmed value or IMON is above 1.20V; may be pulled up to any rail up to 40V. |
| 3 | RT | passive | Frequency set pin; a resistor from this pin to GND sets the switching frequency between 80kHz and 400kHz. |
| 4 | GND | power_in | Signal ground for small-signal and compensation components, connected to PCB ground at one point away from high currents and switching noise. |
| 5 | VDD | power_out | Internally regulated 3.3V supply rail (3.2V to 3.4V) that must be bypassed with a minimum 2.2µF ceramic capacitor and may be used to hold MODE1, MODE2 and SYNC/SPRD logic high. |
| 6 | SS | passive | Soft-start pin where a capacitor to ground sets the inductor current ramp rate; it sources 5µA once switching is enabled and is held at ground while switching is disabled. |
| 7 | IMON | output | Current monitor output sourcing a current proportional to the SNSP2-SNSN2 voltage; a resistor to ground sets the average current limit and regulation transitions to current control above 1.01V. |
| 8 | VC1 | passive | Error amplifier output and compensation point for CCM, DCM and Burst Mode operation, and boost loop compensation in pass-thru mode; the current comparator trip point rises with this voltage. |
| 9 | VC2 | passive | Buck loop error amplifier output and compensation point in pass-thru mode; leave floating if pass-thru mode is not used. |
| 10 | FB2 | input | Error amplifier feedback input for the buck regulation loop in pass-thru mode, fed from an external resistive divider; leave floating if pass-thru mode is not used. |
| 11 | FB1 | input | Error amplifier feedback input for the boost loop in CCM, DCM, Burst Mode and pass-thru operation, regulating to 1.00V nominal from an external resistive divider. |
| 12 | NC | unconnected | Marked NC in the pin configuration; the datasheet defines no function for this pin. |
| 13 | VOUT | input | Output voltage sense that must have a Kelvin connection to the drain of switch D; VINP and VOUT are rated to 100V absolute maximum. |
| 14 | NC | unconnected | Marked NC in the pin configuration; the datasheet defines no function for this pin. |
| 15 | SNSN2 | input | Negative input for the average current sense monitor, connected to the negative terminal of the sense resistor in the input, output or load path. |
| 16 | SNSP2 | input | Positive input for the average current sense monitor, connected to the positive terminal of the sense resistor in the input, output or load path. |
| 17 | NC | unconnected | Marked NC in the pin configuration; the datasheet defines no function for this pin. |
| 18 | TG2 | output | Top gate drive for the boost regulator, swinging GATEVCC superimposed on the SW2 node and held near VOUT + GATEVCC in buck or pass-thru operation. |
| 19 | SW2 | passive | Boost regulator switch node; the negative terminal of the boost bootstrap capacitor connects here. |
| 20 | BST2 | passive | Boosted floating driver supply for the boost regulator that swings from roughly GATEVCC to VOUT + GATEVCC; the positive terminal of the bootstrap capacitor connects here. |
| 21 | BG2 | output | Bottom gate drive for the boost regulator with a voltage swing between GATEVCC and PGND. |
| 22 | PGND | power_in | Driver power ground that connects to CIN, COUT and the MOSFET sources. |
| 23 | BG1 | output | Bottom gate drive for the buck regulator with a voltage swing between GATEVCC and PGND. |
| 24 | GATEVCC | power_out | Gate driver supply internally regulated to 10.6V that must be bypassed to ground with a minimum 4.7µF ceramic capacitor. |
| 25 | EXTVCC | power_in | External supply input for the GATEVCC regulator, used when its voltage is above 8V and below VINP, may be driven up to 40V, and should go through a 100k resistor to ground if unused. |
| 26 | NC | unconnected | Marked NC in the pin configuration; the datasheet defines no function for this pin. |
| 27 | BST1 | passive | Boosted floating driver supply for the buck regulator that swings from roughly GATEVCC to VIN + GATEVCC; the positive terminal of the bootstrap capacitor connects here. |
| 28 | SW1 | passive | Buck regulator switch node; the negative terminal of the buck bootstrap capacitor connects here. |
| 29 | TG1 | output | Top gate drive for the buck regulator, swinging GATEVCC superimposed on the SW1 node and held near VIN + GATEVCC in boost or pass-thru operation. |
| 30 | SNSN1 | input | Negative input for the inductor current sense amplifier, connected across a shunt resistor in series with the inductor on the SW1 side. |
| 31 | SNSP1 | input | Positive input for the inductor current sense amplifier; the SNSP1-SNSN1 voltage is used for current mode control and reverse current detection. |
| 32 | NC | unconnected | Marked NC in the pin configuration; the datasheet defines no function for this pin. |
| 33 | VINP | power_in | Protected main input supply that must connect to the drain of switch A, through a small RC filter (e.g., 1Ω and 1µF) for jitter performance, or to the DG MOSFET drain when reverse input protection is used. |
| 34 | DG | output | Reverse input protection gate drive output that charges to roughly VIN + GATEVCC in normal operation and is clamped to VIN when VIN is below -1.2V; it tolerates negative voltages down to -40V. |
| 35 | VIN | power_in | Input voltage pin powering start-up circuitry and the internal charge pump that withstands negative voltages down to -40V without damage. |
| 36 | NC | unconnected | Marked NC in the pin configuration; the datasheet defines no function for this pin. |
| 37 | EN/UVLO | input | Precision enable input that enables the LT8210 above 1.45V and places it in low-power shutdown below 1.35V; it tolerates negative voltages to -40V and can be tied to VIN for always-on operation. |
| 38 | NC | unconnected | Marked NC in the pin configuration; the datasheet defines no function for this pin. |
| 39 | MODE2 | input | Operating mode selection input #2 that works with MODE1 to select CCM, DCM, Burst Mode or pass-thru operation per Table 1. |
| 40 | MODE1 | input | Operating mode selection input #1 that works with MODE2 to select CCM, DCM, Burst Mode or pass-thru operation per Table 1. |
| 41 | GND | power_in | Exposed pad that is signal ground and must be soldered to the PCB and connected to the GND pin with top-layer metal. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-40-EP(6x6) |
| Category | Power Supply Chip |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, VINP Input Operating Voltage Range | 4.5 | 100 | V | Minimum Voltage for Start-Up (VEXTVCC = 0V) | 4 | ||
| VIN, VINP Input Operating Voltage Range | 2.8 | 100 | V | After Start-Up, VEXTVCC = 12V | 4 | ||
| VIN Quiescent Current | 1 | 5 | µA | Shutdown (VEN/UVLO = 0V) | 4 | ||
| VIN Quiescent Current | 4 | 15 | µA | Not Switching | 4 | ||
| VINP Quiescent Current | 18 | 33 | µA | Pass-Thru (Non-Switching, VINP = 48V) | 4 | ||
| VINP Quiescent Current | 650 | 1300 | µA | Not Switching | 4 | ||
| GATEVCC Voltage | 10 | 10.6 | 11.2 | V | IGATEVCC = 25mA | 4 | |
| GATEVCC Current Limit | 65 | 110 | mA | Regulated from VINP, VINP =12V, VGATEVCC = 9V | 4 | ||
| GATEVCC Regulator Dropout Voltage | 750 | 1600 | mV | VINP, VGATEVCC: IGATEVCC = 50mA | 4 | ||
| GATEVCC Regulator Dropout Voltage | 600 | 1400 | mV | VEXTVCC, VGATEVCC: IGATEVCC = 50mA | 4 | ||
| GATEVCC Undervoltage Lockout Threshold | 3.65 | 3.75 | 3.85 | V | Falling | 4 | |
| EXTVCC Switchover Voltage | 7.3 | 8 | 8.8 | V | Rising | 4 | |
| VDD Voltage | 3.2 | 3.3 | 3.4 | V | 4 | ||
| VDD Undervoltage Lockout Threshold | 2.7 | 2.8 | 2.9 | V | Falling | 4 | |
| EN/UVLO Enable Threshold | 1.28 | 1.45 | 1.61 | V | Rising | 4 | |
| DG Undervoltage Threshold (VDG, VIN) | 2.3 | 2.8 | 3 | V | Rising | 4 | |
| Reverse Input Disconnect Threshold (VIN) | -1.8 | -1.2 | -0.5 | V | IDG = 100 µA | 4 | |
| FB1 Regulation Voltage | 0.9875 | 1 | 1.0125 | V | Regulation Voltage for CCM, DCM, Burst Mode Operation, Pass-Thru Mode Boost Loop | 4 | |
| FB2 Regulation Voltage | 0.985 | 1 | 1.015 | V | Regulation Voltage Pass-Thru Mode Buck Loop | 5 | |
| FB1, FB2 Input Bias Current | 0.001 | 0.04 | µA | 5 | |||
| Soft-Start Charging Current | 4 | 5 | 6 | µA | VSS = 0.5V | 5 | |
| SNSP2, SNSN2 Operating Voltage Range | 0 | 100 | V | 5 | |||
| IMON Output Current | 87.3 | 90 | 92.7 | µA | Common Mode Voltage = 12V, VSNSP2, VSNSN2 = 150mV | 5 | |
| IMON Output Current | 28.6 | 30 | 31.4 | µA | Common Mode Voltage = 12V, VSNSP2, VSNSN2 = 50mV | 5 | |
| IMON Output Current | 5.1 | 6 | 6.6 | µA | Common Mode Voltage = 12V, VSNSP2, VSNSN2 = 10mV | 5 | |
| IMON Output Current | 85 | 90.5 | 95 | µA | Common Mode Voltage = 0V, VSNSP2, VSNSN2 = 150mV | 5 | |
| IMON Regulation Voltage (VIMON) | 0.98 | 1.01 | 1.03 | V | 5 | ||
| Sense Regulation Voltage (VSNSP2, VSNSN2) | 48 | 50.5 | 53 | mV | RIMON = 33.2k | 5 | |
| Over-Current Warning Threshold (VIMON) | 1.15 | 1.2 | 1.24 | V | Rising | 5 | |
| IMON Disable Threshold (VIMON) | 2.3 | 2.5 | 2.8 | V | Rising | 5 | |
| Maximum Current Sense Threshold (VSNSP1, VSNSN1) | 45 | 53 | 60 | mV | Buck Regulation (VINP = 24V, VOUT = 0V) | 5 | |
| Maximum Current Sense Threshold (VSNSP1, VSNSN1) | 55 | 62 | 69 | mV | Buck Regulation (VINP = 24V, VOUT = 12V) | 5 | |
| Maximum Current Sense Threshold (VSNSP1, VSNSN1) | 45 | 51 | 58 | mV | Boost Regulation (VINP = 6V, VOUT = 12V) | 5 | |
| Maximum Current Sense Threshold (VSNSP1, VSNSN1) | 73 | 85 | 96 | mV | Buck Regulation (VINP = 100V, VOUT = 48V) | 5 | |
| Maximum Current Sense Threshold (VSNSP1, VSNSN1) | 36 | 45 | 54 | mV | Boost Regulation (VINP = 24V, VOUT = 48V) | 5 | |
| Maximum Non-Switching Current Sense Threshold in Pass-Thru (VSNSP1, VSNSN1) | 57 | 63 | 70 | mV | VOUT = VINP, FB1 = 1.2V, FB2 = 0.8V, MODE1 = MODE2 = 3.3V | 5 | |
| Switching Frequency Range | 80 | 400 | kHz | RT Set/Synchronized | 6 | ||
| Switching Frequency | 91 | 100 | 108 | kHz | RT = 110k | 6 | |
| Switching Frequency | 190 | 200 | 210 | kHz | RT = 39.2k | 6 | |
| Switching Frequency | 380 | 400 | 420 | kHz | RT = 16.9k | 6 | |
| PWGD Trip Level | -13 | -10 | -8 | % | VFB1 Falling | 6 | |
| PWGD Trip Level | 8 | 10 | 12 | % | VFB2 Rising | 6 | |
| VIN, EN/UVLO Voltage | -40 | 100 | V | 3 | |||
| DG Voltage | -40 | 113 | V | 3 | |||
| DG, VIN Voltage | -0.3 | 13 | V | 3 | |||
| VINP, VOUT, SNSP2, SNSN2 Voltage | -0.3 | 100 | V | 3 | |||
| SNSP1, SNSN1, SNSP2, SNSN2 Voltage | -0.5 | 0.5 | V | 3 | |||
| BST1, BST2 Voltage | -0.3 | 115 | V | 3 | |||
| SW1, SW2, SNSP1, SNSN1 Voltage | 100 | V | Note 5 | 3 | |||
| BST1, SW1, BST2, SW2 Voltage | -0.3 | 15 | V | 3 | |||
| BST1, SNSP1, BST1, SNSN1 Voltage | -0.3 | 15 | V | 3 | |||
| GATEVCC Voltage | -0.3 | 15 | V | 3 | |||
| EXTVCC, PWGD Voltage | -0.3 | 40 | V | 3 | |||
| MODE1, MODE2, SYNC/SPRD Voltage | -0.3 | 6 | V | 3 | |||
| FB1, FB2, IMON, RT Voltage | -0.3 | 6 | V | 3 | |||
| VDD Voltage (absolute maximum) | -0.3 | 6 | V | 3 | |||
| VC1, VC2, SS Voltage | -0.3 | V | Upper limit printed as VDD (Note 6) | 3 | |||
| Operating Junction Temperature (LT8210I) | -40 | 125 | °C | LT8210E, LT8210I (Notes 2, 4) | 3 | ||
| Storage Temperature Range | -65 | 150 | °C | 3 |
CAD (KiCad official)
- Symbol:
LT8210IUJ#TRPBF - Footprint:
Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm - 3D model: QFN-40-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
lt8210iuj-trpbf-etched.step/lt8210iuj-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8210iuj-trpbf.step/lt8210iuj-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (46 pp, sha256
fbfa6905c9f64029, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).