main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs lt8210iuj-trpbf: hero re-rendered with the chip (after the 10-30 render outage) · Ray
viewers lt8210iuj-trpbf: viewers · Ray
lt8210iuj-trpbf-etched.glb Publish 0.1.0 · Ray
lt8210iuj-trpbf-etched.step lt8210iuj-trpbf: factory component page (tier=mfr) · Ray
lt8210iuj-trpbf-hero.glb lt8210iuj-trpbf: hero GLB from the etched model (keeps the MPN mark) · Ray
lt8210iuj-trpbf-hero.overlay.json Publish 0.1.0 · Ray
lt8210iuj-trpbf.glb Publish 0.1.0 · Ray
lt8210iuj-trpbf.kicad_mod Publish 0.1.0 · Ray
lt8210iuj-trpbf.kicad_sym Publish 0.1.0 · Ray
lt8210iuj-trpbf.lbr Publish 0.1.0 · Ray
lt8210iuj-trpbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 41 pins · Ray

LT8210IUJ#TRPBF

Analog Devices · DC-DC Controllers · QFN-40-EP(6x6)

LT8210IUJ#TRPBF from Analog Devices, in a QFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC/SPRD input External clock synchronization input accepting 80kHz to 400kHz; tie to VDD for spread-spectrum operation or to ground otherwise.
2 PWGD output Open-drain power-good output pulled low when the output is outside ±10% of its programmed value or IMON is above 1.20V; may be pulled up to any rail up to 40V.
3 RT passive Frequency set pin; a resistor from this pin to GND sets the switching frequency between 80kHz and 400kHz.
4 GND power_in Signal ground for small-signal and compensation components, connected to PCB ground at one point away from high currents and switching noise.
5 VDD power_out Internally regulated 3.3V supply rail (3.2V to 3.4V) that must be bypassed with a minimum 2.2µF ceramic capacitor and may be used to hold MODE1, MODE2 and SYNC/SPRD logic high.
6 SS passive Soft-start pin where a capacitor to ground sets the inductor current ramp rate; it sources 5µA once switching is enabled and is held at ground while switching is disabled.
7 IMON output Current monitor output sourcing a current proportional to the SNSP2-SNSN2 voltage; a resistor to ground sets the average current limit and regulation transitions to current control above 1.01V.
8 VC1 passive Error amplifier output and compensation point for CCM, DCM and Burst Mode operation, and boost loop compensation in pass-thru mode; the current comparator trip point rises with this voltage.
9 VC2 passive Buck loop error amplifier output and compensation point in pass-thru mode; leave floating if pass-thru mode is not used.
10 FB2 input Error amplifier feedback input for the buck regulation loop in pass-thru mode, fed from an external resistive divider; leave floating if pass-thru mode is not used.
11 FB1 input Error amplifier feedback input for the boost loop in CCM, DCM, Burst Mode and pass-thru operation, regulating to 1.00V nominal from an external resistive divider.
12 NC unconnected Marked NC in the pin configuration; the datasheet defines no function for this pin.
13 VOUT input Output voltage sense that must have a Kelvin connection to the drain of switch D; VINP and VOUT are rated to 100V absolute maximum.
14 NC unconnected Marked NC in the pin configuration; the datasheet defines no function for this pin.
15 SNSN2 input Negative input for the average current sense monitor, connected to the negative terminal of the sense resistor in the input, output or load path.
16 SNSP2 input Positive input for the average current sense monitor, connected to the positive terminal of the sense resistor in the input, output or load path.
17 NC unconnected Marked NC in the pin configuration; the datasheet defines no function for this pin.
18 TG2 output Top gate drive for the boost regulator, swinging GATEVCC superimposed on the SW2 node and held near VOUT + GATEVCC in buck or pass-thru operation.
19 SW2 passive Boost regulator switch node; the negative terminal of the boost bootstrap capacitor connects here.
20 BST2 passive Boosted floating driver supply for the boost regulator that swings from roughly GATEVCC to VOUT + GATEVCC; the positive terminal of the bootstrap capacitor connects here.
21 BG2 output Bottom gate drive for the boost regulator with a voltage swing between GATEVCC and PGND.
22 PGND power_in Driver power ground that connects to CIN, COUT and the MOSFET sources.
23 BG1 output Bottom gate drive for the buck regulator with a voltage swing between GATEVCC and PGND.
24 GATEVCC power_out Gate driver supply internally regulated to 10.6V that must be bypassed to ground with a minimum 4.7µF ceramic capacitor.
25 EXTVCC power_in External supply input for the GATEVCC regulator, used when its voltage is above 8V and below VINP, may be driven up to 40V, and should go through a 100k resistor to ground if unused.
26 NC unconnected Marked NC in the pin configuration; the datasheet defines no function for this pin.
27 BST1 passive Boosted floating driver supply for the buck regulator that swings from roughly GATEVCC to VIN + GATEVCC; the positive terminal of the bootstrap capacitor connects here.
28 SW1 passive Buck regulator switch node; the negative terminal of the buck bootstrap capacitor connects here.
29 TG1 output Top gate drive for the buck regulator, swinging GATEVCC superimposed on the SW1 node and held near VIN + GATEVCC in boost or pass-thru operation.
30 SNSN1 input Negative input for the inductor current sense amplifier, connected across a shunt resistor in series with the inductor on the SW1 side.
31 SNSP1 input Positive input for the inductor current sense amplifier; the SNSP1-SNSN1 voltage is used for current mode control and reverse current detection.
32 NC unconnected Marked NC in the pin configuration; the datasheet defines no function for this pin.
33 VINP power_in Protected main input supply that must connect to the drain of switch A, through a small RC filter (e.g., 1Ω and 1µF) for jitter performance, or to the DG MOSFET drain when reverse input protection is used.
34 DG output Reverse input protection gate drive output that charges to roughly VIN + GATEVCC in normal operation and is clamped to VIN when VIN is below -1.2V; it tolerates negative voltages down to -40V.
35 VIN power_in Input voltage pin powering start-up circuitry and the internal charge pump that withstands negative voltages down to -40V without damage.
36 NC unconnected Marked NC in the pin configuration; the datasheet defines no function for this pin.
37 EN/UVLO input Precision enable input that enables the LT8210 above 1.45V and places it in low-power shutdown below 1.35V; it tolerates negative voltages to -40V and can be tied to VIN for always-on operation.
38 NC unconnected Marked NC in the pin configuration; the datasheet defines no function for this pin.
39 MODE2 input Operating mode selection input #2 that works with MODE1 to select CCM, DCM, Burst Mode or pass-thru operation per Table 1.
40 MODE1 input Operating mode selection input #1 that works with MODE2 to select CCM, DCM, Burst Mode or pass-thru operation per Table 1.
41 GND power_in Exposed pad that is signal ground and must be soldered to the PCB and connected to the GND pin with top-layer metal.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-40-EP(6x6)
Category Power Supply Chip
Pins 41

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, VINP Input Operating Voltage Range 4.5 100 V Minimum Voltage for Start-Up (VEXTVCC = 0V) 4
VIN, VINP Input Operating Voltage Range 2.8 100 V After Start-Up, VEXTVCC = 12V 4
VIN Quiescent Current 1 5 µA Shutdown (VEN/UVLO = 0V) 4
VIN Quiescent Current 4 15 µA Not Switching 4
VINP Quiescent Current 18 33 µA Pass-Thru (Non-Switching, VINP = 48V) 4
VINP Quiescent Current 650 1300 µA Not Switching 4
GATEVCC Voltage 10 10.6 11.2 V IGATEVCC = 25mA 4
GATEVCC Current Limit 65 110 mA Regulated from VINP, VINP =12V, VGATEVCC = 9V 4
GATEVCC Regulator Dropout Voltage 750 1600 mV VINP, VGATEVCC: IGATEVCC = 50mA 4
GATEVCC Regulator Dropout Voltage 600 1400 mV VEXTVCC, VGATEVCC: IGATEVCC = 50mA 4
GATEVCC Undervoltage Lockout Threshold 3.65 3.75 3.85 V Falling 4
EXTVCC Switchover Voltage 7.3 8 8.8 V Rising 4
VDD Voltage 3.2 3.3 3.4 V 4
VDD Undervoltage Lockout Threshold 2.7 2.8 2.9 V Falling 4
EN/UVLO Enable Threshold 1.28 1.45 1.61 V Rising 4
DG Undervoltage Threshold (VDG, VIN) 2.3 2.8 3 V Rising 4
Reverse Input Disconnect Threshold (VIN) -1.8 -1.2 -0.5 V IDG = 100 µA 4
FB1 Regulation Voltage 0.9875 1 1.0125 V Regulation Voltage for CCM, DCM, Burst Mode Operation, Pass-Thru Mode Boost Loop 4
FB2 Regulation Voltage 0.985 1 1.015 V Regulation Voltage Pass-Thru Mode Buck Loop 5
FB1, FB2 Input Bias Current 0.001 0.04 µA 5
Soft-Start Charging Current 4 5 6 µA VSS = 0.5V 5
SNSP2, SNSN2 Operating Voltage Range 0 100 V 5
IMON Output Current 87.3 90 92.7 µA Common Mode Voltage = 12V, VSNSP2, VSNSN2 = 150mV 5
IMON Output Current 28.6 30 31.4 µA Common Mode Voltage = 12V, VSNSP2, VSNSN2 = 50mV 5
IMON Output Current 5.1 6 6.6 µA Common Mode Voltage = 12V, VSNSP2, VSNSN2 = 10mV 5
IMON Output Current 85 90.5 95 µA Common Mode Voltage = 0V, VSNSP2, VSNSN2 = 150mV 5
IMON Regulation Voltage (VIMON) 0.98 1.01 1.03 V 5
Sense Regulation Voltage (VSNSP2, VSNSN2) 48 50.5 53 mV RIMON = 33.2k 5
Over-Current Warning Threshold (VIMON) 1.15 1.2 1.24 V Rising 5
IMON Disable Threshold (VIMON) 2.3 2.5 2.8 V Rising 5
Maximum Current Sense Threshold (VSNSP1, VSNSN1) 45 53 60 mV Buck Regulation (VINP = 24V, VOUT = 0V) 5
Maximum Current Sense Threshold (VSNSP1, VSNSN1) 55 62 69 mV Buck Regulation (VINP = 24V, VOUT = 12V) 5
Maximum Current Sense Threshold (VSNSP1, VSNSN1) 45 51 58 mV Boost Regulation (VINP = 6V, VOUT = 12V) 5
Maximum Current Sense Threshold (VSNSP1, VSNSN1) 73 85 96 mV Buck Regulation (VINP = 100V, VOUT = 48V) 5
Maximum Current Sense Threshold (VSNSP1, VSNSN1) 36 45 54 mV Boost Regulation (VINP = 24V, VOUT = 48V) 5
Maximum Non-Switching Current Sense Threshold in Pass-Thru (VSNSP1, VSNSN1) 57 63 70 mV VOUT = VINP, FB1 = 1.2V, FB2 = 0.8V, MODE1 = MODE2 = 3.3V 5
Switching Frequency Range 80 400 kHz RT Set/Synchronized 6
Switching Frequency 91 100 108 kHz RT = 110k 6
Switching Frequency 190 200 210 kHz RT = 39.2k 6
Switching Frequency 380 400 420 kHz RT = 16.9k 6
PWGD Trip Level -13 -10 -8 % VFB1 Falling 6
PWGD Trip Level 8 10 12 % VFB2 Rising 6
VIN, EN/UVLO Voltage -40 100 V 3
DG Voltage -40 113 V 3
DG, VIN Voltage -0.3 13 V 3
VINP, VOUT, SNSP2, SNSN2 Voltage -0.3 100 V 3
SNSP1, SNSN1, SNSP2, SNSN2 Voltage -0.5 0.5 V 3
BST1, BST2 Voltage -0.3 115 V 3
SW1, SW2, SNSP1, SNSN1 Voltage 100 V Note 5 3
BST1, SW1, BST2, SW2 Voltage -0.3 15 V 3
BST1, SNSP1, BST1, SNSN1 Voltage -0.3 15 V 3
GATEVCC Voltage -0.3 15 V 3
EXTVCC, PWGD Voltage -0.3 40 V 3
MODE1, MODE2, SYNC/SPRD Voltage -0.3 6 V 3
FB1, FB2, IMON, RT Voltage -0.3 6 V 3
VDD Voltage (absolute maximum) -0.3 6 V 3
VC1, VC2, SS Voltage -0.3 V Upper limit printed as VDD (Note 6) 3
Operating Junction Temperature (LT8210I) -40 125 °C LT8210E, LT8210I (Notes 2, 4) 3
Storage Temperature Range -65 150 °C 3

CAD (KiCad official)

  • Symbol: LT8210IUJ#TRPBF
  • Footprint: Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm
  • 3D model: QFN-40-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: lt8210iuj-trpbf-etched.step / lt8210iuj-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8210iuj-trpbf.step / lt8210iuj-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (46 pp, sha256 fbfa6905c9f64029, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF