Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32F091CCU6TR

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-48(7x7)

STM32F091CCU6TR from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup power supply: VBAT = 1.65 to 3.6 V powers the RTC, the external 32 kHz oscillator and the backup registers when VDD is not present.
2 PC13 bidirectional Standard 3.3 V I/O (TC) supplied through the power switch, which sinks only 3 mA, so output use is limited to 2 MHz with 30 pF maximum load and it must not source LEDs; additional functions WKUP2, RTC_TAMP1, RTC_TS, RTC_OUT.
3 PC14-OSC32_IN bidirectional Standard 3.3 V I/O (TC) on the power-switch supply with the same 3 mA and 2 MHz / 30 pF limits as PC13, reset function PC14, additional function OSC32_IN.
4 PC15-OSC32_OUT bidirectional Standard 3.3 V I/O (TC) on the power-switch supply with the same 3 mA and 2 MHz / 30 pF limits as PC13, reset function PC15, additional function OSC32_OUT.
5 PF0-OSC_IN bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions CRS_SYNC and I2C1_SDA, and additional function OSC_IN.
6 PF1-OSC_OUT bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate function I2C1_SCL, and additional function OSC_OUT.
7 NRST bidirectional Active-low device reset: bidirectional pin with embedded weak pull-up (RPU 25 to 55 kΩ) acting as device reset input and internal reset output.
8 VSSA power_in Analog ground.
9 VDDA power_in Analog power supply: VDDA must be equal to or higher than VDD, up to 3.6 V, and at least 2.4 V when the ADC or DAC is used.
10 PA0 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions USART2_CTS, TIM2_CH1_ETR, TSC_G1_IO1, USART4_TX, COMP1_OUT and additional functions RTC_TAMP2, WKUP1, ADC_IN0, COMP1_INM6.
11 PA1 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions EVENTOUT, USART2_RTS, TIM2_CH2, TIM15_CH1N, TSC_G1_IO2, USART4_RX and additional functions ADC_IN1, COMP1_INP.
12 PA2 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions TIM15_CH1, USART2_TX, TIM2_CH3, TSC_G1_IO3, COMP2_OUT and additional functions ADC_IN2, WKUP4, COMP2_INM6.
13 PA3 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions TIM15_CH2, USART2_RX, TIM2_CH4, TSC_G1_IO4 and additional functions ADC_IN3, COMP2_INP.
14 PA4 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions SPI1_NSS, I2S1_WS, USART2_CK, TSC_G2_IO1, TIM14_CH1, USART6_TX and additional functions COMP1_INM4, COMP2_INM4, ADC_IN4, DAC_OUT1.
15 PA5 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions SPI1_SCK, I2S1_CK, CEC, TIM2_CH1_ETR, TSC_G2_IO2, USART6_RX and additional functions COMP1_INM5, COMP2_INM5, ADC_IN5, DAC_OUT2.
16 PA6 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions SPI1_MISO, I2S1_MCK, TIM3_CH1, TIM1_BKIN, TIM16_CH1, COMP1_OUT, TSC_G2_IO3, EVENTOUT, USART3_CTS and additional function ADC_IN6.
17 PA7 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions SPI1_MOSI, I2S1_SD, TIM3_CH2, TIM14_CH1, TIM1_CH1N, TIM17_CH1, COMP2_OUT, TSC_G2_IO4, EVENTOUT and additional function ADC_IN7.
18 PB0 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions TIM3_CH3, TIM1_CH2N, TSC_G3_IO2, EVENTOUT, USART3_CK and additional function ADC_IN8.
19 PB1 bidirectional 3.3 V-tolerant I/O directly connected to ADC (TTa) with alternate functions TIM3_CH4, USART3_RTS, TIM14_CH1, TIM1_CH3N, TSC_G3_IO3 and additional function ADC_IN9.
20 PB2 bidirectional 5 V-tolerant I/O (FT) with alternate function TSC_G3_IO4.
21 PB10 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions SPI2_SCK, I2S2_CK, I2C2_SCL, USART3_TX, CEC, TSC_SYNC, TIM2_CH3.
22 PB11 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions USART3_RX, TIM2_CH4, EVENTOUT, TSC_G6_IO1, I2C2_SDA.
23 VSS power_in Ground; all voltages are referenced to VSS.
24 VDD power_in Digital power supply: VDD = 2.0 to 3.6 V, supplying the I/Os and the internal regulator.
25 PB12 bidirectional 5 V-tolerant I/O (FT) with alternate functions TIM1_BKIN, TIM15_BKIN, SPI2_NSS, I2S2_WS, USART3_CK, TSC_G6_IO2, EVENTOUT.
26 PB13 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions SPI2_SCK, I2S2_CK, I2C2_SCL, USART3_CTS, TIM1_CH1N, TSC_G6_IO3.
27 PB14 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions SPI2_MISO, I2S2_MCK, I2C2_SDA, USART3_RTS, TIM1_CH2N, TIM15_CH1, TSC_G6_IO4.
28 PB15 bidirectional 5 V-tolerant I/O (FT) with alternate functions SPI2_MOSI, I2S2_SD, TIM1_CH3N, TIM15_CH1N, TIM15_CH2 and additional functions WKUP7, RTC_REFIN.
29 PA8 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions USART1_CK, TIM1_CH1, EVENTOUT, MCO, CRS_SYNC.
30 PA9 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions USART1_TX, TIM1_CH2, TIM15_BKIN, MCO, TSC_G4_IO1, I2C1_SCL.
31 PA10 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions USART1_RX, TIM1_CH3, TIM17_BKIN, TSC_G4_IO2, I2C1_SDA.
32 PA11 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions CAN_RX, USART1_CTS, TIM1_CH4, COMP1_OUT, TSC_G4_IO3, EVENTOUT, I2C2_SCL.
33 PA12 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions CAN_TX, USART1_RTS, TIM1_ETR, COMP2_OUT, TSC_G4_IO4, EVENTOUT, I2C2_SDA.
34 PA13 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2; after reset it is SWDIO with the internal pull-up activated, with alternate function IR_OUT.
35 VSS power_in Ground; all voltages are referenced to VSS.
36 VDDIO2 power_in I/O supply for marked I/Os: VDDIO2 = 1.65 to 3.6 V, must not be supplied without a valid VDD supply.
37 PA14 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2; after reset it is SWCLK with the internal pull-down activated, with alternate function USART2_TX.
38 PA15 bidirectional 5 V-tolerant I/O (FT) supplied by VDDIO2, with alternate functions SPI1_NSS, I2S1_WS, USART2_RX, USART4_RTS, TIM2_CH1_ETR, EVENTOUT.
39 PB3 bidirectional 5 V-tolerant I/O (FT) with alternate functions SPI1_SCK, I2S1_CK, TIM2_CH2, TSC_G5_IO1, EVENTOUT, USART5_TX.
40 PB4 bidirectional 5 V-tolerant I/O (FT) with alternate functions SPI1_MISO, I2S1_MCK, TIM17_BKIN, TIM3_CH1, TSC_G5_IO2, EVENTOUT, USART5_RX.
41 PB5 bidirectional 5 V-tolerant I/O (FT) with alternate functions SPI1_MOSI, I2S1_SD, I2C1_SMBA, TIM16_BKIN, TIM3_CH2, USART5_CK_RTS and additional function WKUP6.
42 PB6 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions I2C1_SCL, USART1_TX, TIM16_CH1N, TSC_G5_IO3.
43 PB7 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions I2C1_SDA, USART1_RX, USART4_CTS, TIM17_CH1N, TSC_G5_IO4.
44 PF11-BOOT0 bidirectional 5 V-tolerant I/O (FT) used as BOOT0 for boot memory selection.
45 PB8 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions I2C1_SCL, CEC, TIM16_CH1, TSC_SYNC, CAN_RX.
46 PB9 bidirectional 5 V-tolerant I/O with FM+ capability (FTf) with alternate functions SPI2_NSS, I2S2_WS, I2C1_SDA, IR_OUT, TIM17_CH1, EVENTOUT, CAN_TX.
47 VSS power_in Ground; all voltages are referenced to VSS.
48 VDD power_in Digital power supply: VDD = 2.0 to 3.6 V, supplying the I/Os and the internal regulator.
49 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-48(7x7)
Category Embedded Processors & Controllers
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage VDD-VSS -0.3 4 V 52
External I/O supply voltage VDDIO2-VSS -0.3 4 V 52
External analog supply voltage VDDA-VSS -0.3 4 V 52
Allowed voltage difference for VDD > VDDA VDD-VDDA 0.4 V VDD > VDDA 52
External backup supply voltage VBAT-VSS -0.3 4 V 52
Input voltage on TTa pins VIN 4 V 52
Input voltage on any other pin VIN 4 V 52
Variations between different VDD power pins /∆VDDx/ 50 mV 52
Variations between all the different ground pins /VSSx - VSS/ 50 mV 52
Total current into sum of all VDD power lines (source) ΣIVDD 120 mA 53
Total current out of sum of all VSS ground lines (sink) ΣIVSS -120 mA 53
Maximum current into each VDD power pin (source) IVDD(PIN) 100 mA 53
Maximum current out of each VSS ground pin (sink) IVSS(PIN) -100 mA 53
Output current sunk by any I/O and control pin IIO(PIN) 25 mA 53
Output current source by any I/O and control pin IIO(PIN) -25 mA 53
Total output current sunk by sum of all I/Os and control pins ΣIIO(PIN) 80 mA 53
Total output current sourced by sum of all I/Os and control pins ΣIIO(PIN) -80 mA 53
Total output current sourced by sum of all I/Os supplied by VDDIO2 ΣIIO(PIN) -40 mA 53
Injected current on FT and FTf pins IINJ(PIN) -5 0 mA 53
Injected current on TC and RST pin IINJ(PIN) -5 5 mA 53
Injected current on TTa pins IINJ(PIN) -5 5 mA 53
Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) -25 25 mA 53
Storage temperature range TSTG -65 150 °C 53
Maximum junction temperature TJ 150 °C 53
Internal AHB clock frequency fHCLK 0 48 MHz 54
Internal APB clock frequency fPCLK 0 48 MHz 54
Standard operating voltage VDD 2 3.6 V 54
I/O supply voltage VDDIO2 1.65 3.6 V Must not be supplied if VDD is not present 54
Analog operating voltage (ADC and DAC not used) VDDA 3.6 V Must have a potential equal to or higher than VDD 54
Analog operating voltage (ADC and DAC used) VDDA 2.4 3.6 V ADC and DAC used 54
Backup operating voltage VBAT 1.65 3.6 V 54
I/O input voltage VIN -0.3 V TC and RST I/O 54
I/O input voltage VIN -0.3 5.5 V FT and FTf I/O 54
Power dissipation (UFQFPN48) PD 625 mW TA = 85 °C for suffix 6 54
Ambient temperature for the suffix 6 version (maximum power dissipation) TA -40 85 °C Suffix 6 version; maximum power dissipation 54
Ambient temperature for the suffix 6 version (low power dissipation) TA -40 105 °C Suffix 6 version; low power dissipation 54
Junction temperature range TJ -40 105 °C Suffix 6 version 54
VDD rise time rate tVDD 0 µs/V 55
VDD fall time rate tVDD 20 µs/V 55
VDDA rise time rate tVDDA 0 µs/V 55
VDDA fall time rate tVDDA 20 µs/V 55
Power on/power down reset threshold VPOR/PDR 1.8 1.88 1.96 V Falling edge 55
Power on/power down reset threshold VPOR/PDR 1.84 1.92 2 V Rising edge 55
Reset temporization tRSTTEMPO 1.5 2.5 4.5 ms 55
Internal reference voltage VREFINT 1.2 1.23 1.25 V -40 °C < TA < +105 °C 56
ADC_IN17 buffer startup time tSTART 10 µs 56
ADC sampling time when reading the internal reference voltage tS_vrefint 4 µs 56
Internal reference voltage spread over the temperature range ∆VREFINT 10 mV VDDA = 3 V 56
Temperature coefficient TCoeff -100 100 ppm/°C 56
PVD current consumption IDD(PVD) 0.15 0.26 µA 56
Comparator hysteresis Vhys 3 8 13 mV COMPxHYST[1:0]=01; high speed mode 92
Comparator hysteresis Vhys 7 15 26 mV COMPxHYST[1:0]=10; high speed mode 92
Comparator hysteresis Vhys 18 31 49 mV COMPxHYST[1:0]=11; high speed mode 92
PVD threshold 0 rising edge VPVD0 2.1 2.18 2.26 V Rising edge 55
PVD threshold 0 falling edge VPVD0 2 2.08 2.16 V Falling edge 55
PVD threshold 3 rising edge VPVD3 2.38 2.48 2.58 V Rising edge 55
PVD threshold 3 falling edge VPVD3 2.28 2.38 2.48 V Falling edge 55
PVD threshold 7 rising edge VPVD7 2.76 2.88 3 V Rising edge 56
PVD threshold 7 falling edge VPVD7 2.66 2.78 2.9 V Falling edge 56

CAD (KiCad official)

  • Symbol: STM32F091CCU6TR
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: stm32f091ccu6tr-etched.step / stm32f091ccu6tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32f091ccu6tr.step / stm32f091ccu6tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (128 pp, sha256 f96a82f50344c619, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF