Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LTM4622AEY#PBF

Analog Devices · DC-DC Converters · BGA-25

LTM4622AEY#PBF from Analog Devices, in a BGA-25. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
A1 VOUT2 power_out Power output pin of channel 2 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND.
A2 VIN2 power_in Power input pin for channel 2, with input voltage applied between the VIN pins and GND, and channel 2 will not work without VIN1 above 3.6V.
A3 TRACK/SS2 passive Output tracking and soft-start pin for channel 2; below 0.6V it servos FB2 to the track voltage, and the internal 1.2µA pull-up from INTVCC with a capacitor sets a soft-start time with a default minimum of 400µs.
A4 FB2 input Negative input of the channel 2 error amplifier, internally connected to VOUT2 through a 60.4k precision resistor, with tying FB pins together allowed for PolyPhase parallel operation.
A5 COMP2 passive Current control threshold and error amplifier compensation point for channel 2, with a normal range from 0.3V to 1.8V; the device is internally compensated and this pin must not be driven.
B1 VOUT2 power_out Power output pin of channel 2 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND.
B2 RUN2 input Run control input for channel 2; tying RUN above 1.27V enables the channel, tying it below 1V shuts the channel down, and this pin must not float.
B3 VIN2 power_in Power input pin for channel 2, with input voltage applied between the VIN pins and GND, and channel 2 will not work without VIN1 above 3.6V.
B4 PGOOD2 output Open-drain power good output for channel 2, pulled to ground when the FB2 voltage is not within ±8% (typical) of the internal 0.6V reference.
B5 GND power_in Power ground pin for both input and output returns.
C1 GND power_in Power ground pin for both input and output returns.
C2 GND power_in Power ground pin for both input and output returns.
C3 INTVCC power_out Internal 3.3V regulator output that powers the internal power drivers and control circuits, internally decoupled to GND with a 2.2µF low ESR ceramic capacitor.
C4 FREQ passive Frequency set pin with the default internally set to 1MHz; a resistor to GND increases frequency, a resistor to INTVCC reduces it, and the programmable range is 800kHz to 4MHz.
C5 SYNC/MODE input Mode select and external synchronization input; tying to ground forces continuous synchronous operation, floating or tying to INTVCC enables Burst Mode operation at light loads, and an external clock must be within ±30% of the set frequency.
D1 VOUT1 power_out Power output pin of channel 1 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND.
D2 RUN1 input Run control input for channel 1; tying RUN above 1.27V enables the channel, tying it below 1V shuts the channel down, and this pin must not float.
D3 VIN1 power_in Power input pin for channel 1 that also supplies the internal control circuitry, with input voltage applied between the VIN pins and GND over a 3.6V to 20V range.
D4 PGOOD1 output Open-drain power good output for channel 1, pulled to ground when the FB1 voltage is not within ±8% (typical) of the internal 0.6V reference.
D5 GND power_in Power ground pin for both input and output returns.
E1 VOUT1 power_out Power output pin of channel 1 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND.
E2 VIN1 power_in Power input pin for channel 1 that also supplies the internal control circuitry, with input voltage applied between the VIN pins and GND over a 3.6V to 20V range.
E3 TRACK/SS1 passive Output tracking and soft-start pin for channel 1; below 0.6V it servos FB1 to the track voltage, and the internal 1.2µA pull-up from INTVCC with a capacitor sets a soft-start time with a default minimum of 400µs.
E4 FB1 input Negative input of the channel 1 error amplifier, internally connected to VOUT1 through a 60.4k precision resistor, with tying FB pins together allowed for PolyPhase parallel operation.
E5 COMP1 passive Current control threshold and error amplifier compensation point for channel 1, with a normal range from 0.3V to 1.8V; the device is internally compensated and this pin must not be driven.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package BGA-25
Category Power Supply Chip
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input DC Voltage Range VIN1 VIN1 3.6 20 V 3
Input DC Voltage Range VIN2 VIN2 1.5 20 V 3.6V < VIN1 < 20V 3
Output Voltage Range VOUT(RANGE) 1.5 12 V VIN1 = VIN2 = 3.6V to 20V 3
Output Voltage, Total Variation with Line and Load VOUT(DC) 1.477 1.5 1.523 V CIN = 22µF, COUT = 100µF Ceramic, RFB = 40.2k, MODE = INTVCC, VIN1 = VIN2 = 3.6V to 20V, IOUT = 0A to 2A 3
RUN Pin On Threshold, Rising VRUN 1.2 1.27 1.35 V RUN Threshold Rising 3
RUN Pin On Threshold, Falling VRUN 0.97 1 1.03 V RUN Threshold Falling 3
Output Continuous Current Range IOUT(DC) 0 2 A VIN1 = VIN2 = 12V, VOUT = 1.5V (Note 3) 3
Line Regulation Accuracy ΔVOUT(Line)/VOUT 0.01 0.1 %/V VOUT = 1.5V, VIN1 = VIN2 = 3.6V to 20V, IOUT = 0A 3
Load Regulation Accuracy ΔVOUT(Load)/VOUT 0.2 1 % VOUT = 1.5V, IOUT = 0A to 2A 3
Feedback Voltage at FB Pin VFB 0.592 0.6 0.608 V IOUT = 0A, VOUT = 1.5V 3
Current at FB Pin IFB -30 30 nA Note 4 3
Resistor Between VOUT and FB Pins RFBHI 60 60.4 60.8 kΩ 3
PGOOD Trip Level, VFB Ramping Negative VPGOOD -14 -8 % VFB With Respect to Set Output, VFB Ramping Negative 3
PGOOD Trip Level, VFB Ramping Positive VPGOOD 8 14 % VFB With Respect to Set Output, VFB Ramping Positive 3
VINTVCC Internal VCC Voltage VINTVCC 3.1 3.3 3.5 V VIN1 = VIN2 = 3.6V to 20V 3
INTVCC Load Regulation VINTVCC Load Reg 1.3 % ICC = 0mA to 50mA 3
Frequency Sync Range fSYNC -30 30 % With Respect to Set Frequency 3
MODE Input Current IMODE -1.5 µA MODE = INTVCC 3
Input Supply Bias Current IQ(VIN) 7 mA VIN1 = VIN2 = 12V, VOUT = 1.5V, MODE = GND 3
Input Supply Bias Current IQ(VIN) 500 µA VIN1 = VIN2 = 12V, VOUT = 1.5V, MODE = INTVCC 3
Input Supply Bias Current, Shutdown IQ(VIN) 45 µA Shutdown, RUN1 = RUN2 = 0 3
Input Supply Current IS(VIN) 0.32 A VIN1 = VIN2 = 12V, VOUT = 1.5V, IOUT = 2A 3
Output Current Limit IOUTPK 3 4 A VIN1 = VIN2 = 12V, VOUT = 1.5V 3
Output Ripple Voltage VOUT(AC) 5 mV IOUT = 0A, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V 3
Turn-On Overshoot ΔVOUT(START) 30 mV IOUT = 0A, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V 3
Turn-On Time tSTART 5.5 ms COUT = 100µF Ceramic, No Load, TRACK/SS = 0.01µF, VIN1 = VIN2 = 12V, VOUT = 1.5V 3
Peak Deviation for Dynamic Load ΔVOUTLS 100 mV Load: 0% to 50% to 0% of Full Load, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V 3
Settling Time for Dynamic Load Step tSETTLE 20 µs Load: 0% to 50% to 0% of Full Load, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V 3
Track Pin Soft-Start Pull-Up Current ITRACK/SS 1.2 µA TRACK/SS = 0V 3
Internal Soft-Start Time tSS 400 700 µs 10% to 90% Rise Time (Note 4) 3
Minimum On-Time tON(MIN) 20 ns Note 4 3
Minimum Off-Time tOFF(MIN) 45 ns Note 4 3
PGOOD Pull-Down Resistance RPGOOD 20 Ω 1mA Load 3
Oscillator Frequency fOSC 1 MHz 3
Input Pin Voltage Absolute Maximum VIN1, VIN2 VIN1, VIN2 -0.3 22 V 2
VOUT Absolute Maximum VOUT -0.3 16 V 2
PGOOD1, PGOOD2 Absolute Maximum PGOOD1, PGOOD2 -0.3 18 V 2
RUN1, RUN2 Absolute Maximum RUN1, RUN2 -0.3 V max = VIN + 0.3V 2
INTVCC, TRACK/SS1, TRACK/SS2 Absolute Maximum INTVCC, TRACK/SS1, TRACK/SS2 -0.3 3.6 V 2
SYNC/MODE, COMP1, COMP2, FB1, FB2 Absolute Maximum SYNC/MODE, COMP1, COMP2, FB1, FB2 -0.3 V max = INTVCC 2
Operating Internal Temperature Range TJ -40 125 °C Note 2 2
Storage Temperature Range TSTG -55 125 °C 2
Maximum Junction Temperature TJMAX 125 °C BGA package 2
Thermal Resistance, Junction to Case (Top) θJCtop 17 °C/W BGA package 2
Thermal Resistance, Junction to Case (Bottom) θJCbottom 11 °C/W BGA package 2
Thermal Resistance, Junction to Board plus Board to Ambient θJB + θBA 22 °C/W BGA package 2
Thermal Resistance, Junction to Ambient θJA 22 °C/W BGA package 2

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper • Use a separated SGND ground copper area for com￾ponents connected to signal pins. Connect the SGND 21

CAD (KiCad official)

  • Symbol: LTM4622AEY#PBF
  • Footprint: Package_BGA:BGA-25_6.35x6.35mm_Layout5x5_P1.27mm
  • 3D model: BGA-25 (KiCad packages3D, STEP)
  • 3D model files: ltm4622aey-pbf-etched.step / ltm4622aey-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltm4622aey-pbf.step / ltm4622aey-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 e206684e57fff3b5, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF