Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LTM4622AEY#PBF
Analog Devices · DC-DC Converters · BGA-25
LTM4622AEY#PBF from Analog Devices, in a BGA-25. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| A1 | VOUT2 | power_out | Power output pin of channel 2 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND. |
| A2 | VIN2 | power_in | Power input pin for channel 2, with input voltage applied between the VIN pins and GND, and channel 2 will not work without VIN1 above 3.6V. |
| A3 | TRACK/SS2 | passive | Output tracking and soft-start pin for channel 2; below 0.6V it servos FB2 to the track voltage, and the internal 1.2µA pull-up from INTVCC with a capacitor sets a soft-start time with a default minimum of 400µs. |
| A4 | FB2 | input | Negative input of the channel 2 error amplifier, internally connected to VOUT2 through a 60.4k precision resistor, with tying FB pins together allowed for PolyPhase parallel operation. |
| A5 | COMP2 | passive | Current control threshold and error amplifier compensation point for channel 2, with a normal range from 0.3V to 1.8V; the device is internally compensated and this pin must not be driven. |
| B1 | VOUT2 | power_out | Power output pin of channel 2 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND. |
| B2 | RUN2 | input | Run control input for channel 2; tying RUN above 1.27V enables the channel, tying it below 1V shuts the channel down, and this pin must not float. |
| B3 | VIN2 | power_in | Power input pin for channel 2, with input voltage applied between the VIN pins and GND, and channel 2 will not work without VIN1 above 3.6V. |
| B4 | PGOOD2 | output | Open-drain power good output for channel 2, pulled to ground when the FB2 voltage is not within ±8% (typical) of the internal 0.6V reference. |
| B5 | GND | power_in | Power ground pin for both input and output returns. |
| C1 | GND | power_in | Power ground pin for both input and output returns. |
| C2 | GND | power_in | Power ground pin for both input and output returns. |
| C3 | INTVCC | power_out | Internal 3.3V regulator output that powers the internal power drivers and control circuits, internally decoupled to GND with a 2.2µF low ESR ceramic capacitor. |
| C4 | FREQ | passive | Frequency set pin with the default internally set to 1MHz; a resistor to GND increases frequency, a resistor to INTVCC reduces it, and the programmable range is 800kHz to 4MHz. |
| C5 | SYNC/MODE | input | Mode select and external synchronization input; tying to ground forces continuous synchronous operation, floating or tying to INTVCC enables Burst Mode operation at light loads, and an external clock must be within ±30% of the set frequency. |
| D1 | VOUT1 | power_out | Power output pin of channel 1 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND. |
| D2 | RUN1 | input | Run control input for channel 1; tying RUN above 1.27V enables the channel, tying it below 1V shuts the channel down, and this pin must not float. |
| D3 | VIN1 | power_in | Power input pin for channel 1 that also supplies the internal control circuitry, with input voltage applied between the VIN pins and GND over a 3.6V to 20V range. |
| D4 | PGOOD1 | output | Open-drain power good output for channel 1, pulled to ground when the FB1 voltage is not within ±8% (typical) of the internal 0.6V reference. |
| D5 | GND | power_in | Power ground pin for both input and output returns. |
| E1 | VOUT1 | power_out | Power output pin of channel 1 switching regulator; apply the load between the VOUT pins and GND pins and place output decoupling directly between these pins and GND. |
| E2 | VIN1 | power_in | Power input pin for channel 1 that also supplies the internal control circuitry, with input voltage applied between the VIN pins and GND over a 3.6V to 20V range. |
| E3 | TRACK/SS1 | passive | Output tracking and soft-start pin for channel 1; below 0.6V it servos FB1 to the track voltage, and the internal 1.2µA pull-up from INTVCC with a capacitor sets a soft-start time with a default minimum of 400µs. |
| E4 | FB1 | input | Negative input of the channel 1 error amplifier, internally connected to VOUT1 through a 60.4k precision resistor, with tying FB pins together allowed for PolyPhase parallel operation. |
| E5 | COMP1 | passive | Current control threshold and error amplifier compensation point for channel 1, with a normal range from 0.3V to 1.8V; the device is internally compensated and this pin must not be driven. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | BGA-25 |
| Category | Power Supply Chip |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input DC Voltage Range VIN1 | VIN1 | 3.6 | 20 | V | 3 | ||
| Input DC Voltage Range VIN2 | VIN2 | 1.5 | 20 | V | 3.6V < VIN1 < 20V | 3 | |
| Output Voltage Range | VOUT(RANGE) | 1.5 | 12 | V | VIN1 = VIN2 = 3.6V to 20V | 3 | |
| Output Voltage, Total Variation with Line and Load | VOUT(DC) | 1.477 | 1.5 | 1.523 | V | CIN = 22µF, COUT = 100µF Ceramic, RFB = 40.2k, MODE = INTVCC, VIN1 = VIN2 = 3.6V to 20V, IOUT = 0A to 2A | 3 |
| RUN Pin On Threshold, Rising | VRUN | 1.2 | 1.27 | 1.35 | V | RUN Threshold Rising | 3 |
| RUN Pin On Threshold, Falling | VRUN | 0.97 | 1 | 1.03 | V | RUN Threshold Falling | 3 |
| Output Continuous Current Range | IOUT(DC) | 0 | 2 | A | VIN1 = VIN2 = 12V, VOUT = 1.5V (Note 3) | 3 | |
| Line Regulation Accuracy | ΔVOUT(Line)/VOUT | 0.01 | 0.1 | %/V | VOUT = 1.5V, VIN1 = VIN2 = 3.6V to 20V, IOUT = 0A | 3 | |
| Load Regulation Accuracy | ΔVOUT(Load)/VOUT | 0.2 | 1 | % | VOUT = 1.5V, IOUT = 0A to 2A | 3 | |
| Feedback Voltage at FB Pin | VFB | 0.592 | 0.6 | 0.608 | V | IOUT = 0A, VOUT = 1.5V | 3 |
| Current at FB Pin | IFB | -30 | 30 | nA | Note 4 | 3 | |
| Resistor Between VOUT and FB Pins | RFBHI | 60 | 60.4 | 60.8 | kΩ | 3 | |
| PGOOD Trip Level, VFB Ramping Negative | VPGOOD | -14 | -8 | % | VFB With Respect to Set Output, VFB Ramping Negative | 3 | |
| PGOOD Trip Level, VFB Ramping Positive | VPGOOD | 8 | 14 | % | VFB With Respect to Set Output, VFB Ramping Positive | 3 | |
| VINTVCC Internal VCC Voltage | VINTVCC | 3.1 | 3.3 | 3.5 | V | VIN1 = VIN2 = 3.6V to 20V | 3 |
| INTVCC Load Regulation | VINTVCC Load Reg | 1.3 | % | ICC = 0mA to 50mA | 3 | ||
| Frequency Sync Range | fSYNC | -30 | 30 | % | With Respect to Set Frequency | 3 | |
| MODE Input Current | IMODE | -1.5 | µA | MODE = INTVCC | 3 | ||
| Input Supply Bias Current | IQ(VIN) | 7 | mA | VIN1 = VIN2 = 12V, VOUT = 1.5V, MODE = GND | 3 | ||
| Input Supply Bias Current | IQ(VIN) | 500 | µA | VIN1 = VIN2 = 12V, VOUT = 1.5V, MODE = INTVCC | 3 | ||
| Input Supply Bias Current, Shutdown | IQ(VIN) | 45 | µA | Shutdown, RUN1 = RUN2 = 0 | 3 | ||
| Input Supply Current | IS(VIN) | 0.32 | A | VIN1 = VIN2 = 12V, VOUT = 1.5V, IOUT = 2A | 3 | ||
| Output Current Limit | IOUTPK | 3 | 4 | A | VIN1 = VIN2 = 12V, VOUT = 1.5V | 3 | |
| Output Ripple Voltage | VOUT(AC) | 5 | mV | IOUT = 0A, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V | 3 | ||
| Turn-On Overshoot | ΔVOUT(START) | 30 | mV | IOUT = 0A, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V | 3 | ||
| Turn-On Time | tSTART | 5.5 | ms | COUT = 100µF Ceramic, No Load, TRACK/SS = 0.01µF, VIN1 = VIN2 = 12V, VOUT = 1.5V | 3 | ||
| Peak Deviation for Dynamic Load | ΔVOUTLS | 100 | mV | Load: 0% to 50% to 0% of Full Load, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V | 3 | ||
| Settling Time for Dynamic Load Step | tSETTLE | 20 | µs | Load: 0% to 50% to 0% of Full Load, COUT = 100µF Ceramic, VIN1 = VIN2 = 12V, VOUT = 1.5V | 3 | ||
| Track Pin Soft-Start Pull-Up Current | ITRACK/SS | 1.2 | µA | TRACK/SS = 0V | 3 | ||
| Internal Soft-Start Time | tSS | 400 | 700 | µs | 10% to 90% Rise Time (Note 4) | 3 | |
| Minimum On-Time | tON(MIN) | 20 | ns | Note 4 | 3 | ||
| Minimum Off-Time | tOFF(MIN) | 45 | ns | Note 4 | 3 | ||
| PGOOD Pull-Down Resistance | RPGOOD | 20 | Ω | 1mA Load | 3 | ||
| Oscillator Frequency | fOSC | 1 | MHz | 3 | |||
| Input Pin Voltage Absolute Maximum VIN1, VIN2 | VIN1, VIN2 | -0.3 | 22 | V | 2 | ||
| VOUT Absolute Maximum | VOUT | -0.3 | 16 | V | 2 | ||
| PGOOD1, PGOOD2 Absolute Maximum | PGOOD1, PGOOD2 | -0.3 | 18 | V | 2 | ||
| RUN1, RUN2 Absolute Maximum | RUN1, RUN2 | -0.3 | V | max = VIN + 0.3V | 2 | ||
| INTVCC, TRACK/SS1, TRACK/SS2 Absolute Maximum | INTVCC, TRACK/SS1, TRACK/SS2 | -0.3 | 3.6 | V | 2 | ||
| SYNC/MODE, COMP1, COMP2, FB1, FB2 Absolute Maximum | SYNC/MODE, COMP1, COMP2, FB1, FB2 | -0.3 | V | max = INTVCC | 2 | ||
| Operating Internal Temperature Range | TJ | -40 | 125 | °C | Note 2 | 2 | |
| Storage Temperature Range | TSTG | -55 | 125 | °C | 2 | ||
| Maximum Junction Temperature | TJMAX | 125 | °C | BGA package | 2 | ||
| Thermal Resistance, Junction to Case (Top) | θJCtop | 17 | °C/W | BGA package | 2 | ||
| Thermal Resistance, Junction to Case (Bottom) | θJCbottom | 11 | °C/W | BGA package | 2 | ||
| Thermal Resistance, Junction to Board plus Board to Ambient | θJB + θBA | 22 | °C/W | BGA package | 2 | ||
| Thermal Resistance, Junction to Ambient | θJA | 22 | °C/W | BGA package | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND | 21 |
CAD (KiCad official)
- Symbol:
LTM4622AEY#PBF - Footprint:
Package_BGA:BGA-25_6.35x6.35mm_Layout5x5_P1.27mm - 3D model: BGA-25 (KiCad packages3D, STEP)
- 3D model files:
ltm4622aey-pbf-etched.step/ltm4622aey-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltm4622aey-pbf.step/ltm4622aey-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
e206684e57fff3b5, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).