by John Lauer
An independently designed 12 V to 5 V, 1 A synchronous buck molecule (TI TPS54202), with calculations, ngspice and PSpice simulation, KiCad 10 schematic and board, and the board laid out and analysed with adom-aiflow.
main
John Lauer
ECAS study: Adom Fields' own hot-plug check agrees
637a81c
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312
{
"board": "12 V to 5 V / 1 A buck molecule (TI TPS54202 synchronous buck, 500 kHz), 28 x 20 mm, 2 layers, medium machine pins on a 24 x 16 mm grid",
"copperUm": 17.5,
"copperNote": "designed for 0.5 oz outer copper, the conservative end of the fab's range",
"clearance": 0.15,
"edgeClearance": 0.3,
"inheritedErrors": 0,
"fixedRefs": [
"MP1",
"MP2",
"MP3",
"MP4",
"J1",
"J2",
"J3",
"J4",
"J5",
"J6"
],
"fixedRefsNote": "the molecule interface: four corner machine pins (GND) and six contacts on the 2 mm grid; the scaffold and the control-panel wiring depend on these positions",
"planes": {},
"wideNets": {
"VIN": [
0.8,
0.5,
0.3
],
"VOUT": [
0.8,
0.5,
0.3
],
"SW": [
0.8,
0.5,
0.3
],
"GND": [
0.8,
0.5,
0.3
]
},
"midNets": {
"BOOT": [
0.3,
0.2
]
},
"kelvin": {
"R3.2": "U1.1",
"R1.1": "C6.1"
},
"kelvinNote": "datasheet 7.4.1: the feedback divider's ground returns to the IC GND pin on its own trace, and the top of the divider senses VOUT at the output capacitor, not along the load current path",
"loads": {
"VOUT": {
"amps": 1.0,
"maxRiseC": 10
},
"SW": {
"amps": 1.0,
"maxRiseC": 10
},
"GND": {
"amps": 1.0,
"maxRiseC": 10
},
"VIN": {
"amps": 0.6,
"maxRiseC": 10
}
},
"loadsNote": "VIN is the input current at the 9 V low end of the range (5 W / 0.93 / 9 V = 0.6 A); SW carries the inductor RMS current, 1.01 A",
"hot": {
"U1": {
"watts": 0.25,
"tabNet": "GND",
"note": "SOT-23-6 has no exposed pad: heat leaves through the pins, mostly GND (pin 1, low-side source) and VIN (pin 3)"
},
"L1": {
"watts": 0.12,
"tabNet": "VOUT"
}
},
"hotNote": "U1: I^2R at the hot Rds(on) (1.4 x 148 / 78 mOhm) over the duty at 12 V: 0.15 W, plus about 0.09 W switching (15 ns edges, 500 kHz) and gate drive: 0.25 W. L1: 1.01 A RMS squared x 118 mOhm max DCR = 0.12 W.",
"hotMaxRiseC": 55,
"hotMaxRiseNote": "John approved 2026-09-29 (option 2, junction-based): the budget is the pin/tab rise in STILL air. U1 +44 C at its GND pin; psi_JB 33.7 C/W x 0.25 W adds about 8 C to the junction, so Tj is about ambient + 52 C: 92 C at a 40 C ambient, 33 C under the 125 C rating. L1 +41 C is inside its -40..+125 C rating including self-heating. In moving air (25 W/m2K) both are under 30 C (U1 +24, L1 +21). A 28 x 20 mm board losing 0.37 W to still air averages about +33 C even with perfect copper, so 30 C still air is area-limited, not layout-limited: adding 8 more GND vias at the nearest free spots (2.6 to 3.8 mm from U1.1) changed U1 by 0 C in the Fields solve, so they were not added.",
"pours": [
{
"net": "GND",
"outline": true,
"layers": [
"F.Cu",
"B.Cu"
],
"priority": 0,
"connection": "thermal",
"thermalGap": 0.25,
"thermalBridge": 0.35,
"name": "GND both layers"
},
{
"net": "VIN",
"around": [
"J1",
"C1.1",
"C2.1",
"C3.1",
"C4.1",
"U1.3"
],
"margin": 0.5,
"layers": [
"F.Cu"
],
"priority": 2,
"connection": "solid",
"name": "VIN input loop F.Cu"
},
{
"net": "VOUT",
"around": [
"L1.2",
"C6.1",
"C7.1",
"C8.1",
"J4",
"TP3"
],
"margin": 0.5,
"layers": [
"F.Cu"
],
"priority": 2,
"connection": "solid",
"name": "VOUT output F.Cu"
},
{
"net": "SW",
"layers": [
"F.Cu"
],
"priority": 3,
"connection": "solid",
"name": "SW node patch F.Cu (U1.2 to L1.1, widening toward the inductor)",
"polygon": [
[
113.3,
90.52
],
[
113.85,
90.52
],
[
114.6,
89.1
],
[
118.1,
89.1
],
[
118.1,
92.9
],
[
114.9,
92.9
],
[
113.85,
91.48
],
[
113.3,
91.48
]
]
}
],
"poursNote": "The input hot loop (C2/C3/C4 -> U1 VIN -> U1 GND -> C GND) stays on F.Cu over an unbroken B.Cu GND; SW is a short wide trace only, never a pour, to keep the switching node's area (and its radiated field) small. Rev 2 (after the Fields solve): a small solid SW patch between U1.2 and L1.1 removes the 0.27 mm neck while keeping the node's area small; U1's GND pin gets a solid connection and three thermal vias into the B.Cu ground plane (it is the IC's main heat path); the inductor pads connect solid.",
"notPoured": [
"BOOT",
"FB",
"FBM",
"EN",
"VMON",
"LED"
],
"notPouredNote": "bootstrap (dv/dt), the feedback network (high impedance, keep it small and away from SW), the enable and monitor dividers; SW only as the small patch above",
"stitchViasNote": "Two thermal vias under U1.1 (GND pin, the IC's main heat path) and one beside C4.2, placed by hand in solid GND copper clear of SW copper (the planner's thermalVias put one 0.8 mm via inside the SOT-23 pad).",
"solidAt": [
"U1.1",
"U1.3",
"L1.1",
"L1.2"
],
"stitchVias": [
{
"net": "GND",
"x": 113.3,
"y": 92.55,
"size": 0.6,
"drill": 0.3
},
{
"net": "GND",
"x": 113.9,
"y": 92.75,
"size": 0.6,
"drill": 0.3
},
{
"net": "GND",
"x": 115.55,
"y": 88.45,
"size": 0.6,
"drill": 0.3
}
],
"fabNote": "3rd party fab, 2-layer, 1.6 mm FR4",
"fab": {
"rules": "fab",
"target": "fab"
},
"sourcing": {
"profile": "fab"
},
"molecule": {
"pin": "medium",
"gridMm": 2,
"edgeMarginMm": 2,
"cornerPinsNet": "GND"
},
"planeUnder": [
{
"layer": "B.Cu",
"net": "GND",
"name": "GND under the input hot loop",
"polygon": [
[
111.5,
82.9
],
[
116.4,
82.9
],
[
116.4,
92.6
],
[
112.1,
92.6
],
[
112.1,
89.3
],
[
111.5,
89.3
]
]
}
],
"chains": [
{
"refs": [
"R1",
"R2",
"C9"
],
"direction": "down"
}
],
"requireEvidence": [
"calcs",
"simulation"
],
"planeUnderNote": "the input hot loop runs from C2/C3/C4 to U1 VIN (pin 3) and GND (pin 1), all on the right of U1; B.Cu under it stays GND so the loop's return images directly beneath it. The polygon covers the three input caps and narrows to U1 pins 1 and 3 below y 89.3, leaving U1's left pins (FB, EN, BOOT) a way down to B.Cu.",
"voltages": {
"VIN": 12,
"VOUT": 5
},
"sources": {
"VOUT": [
"L1"
],
"SW": [
"U1"
]
},
"switching": {
"SW": {
"highV": 12,
"lowV": 0,
"freqHz": 500000,
"meanV": 5,
"riseNs": 8
}
},
"capCurves": "curves",
"pdn": {
"VIN": {
"sourceOhm": 0.05,
"sourceNh": 1000
}
}
}