main
History Download
Ray Publish 0.1.0 8f2096b

ZXLD1320DCATC

Diodes Incorporated · LED Drivers · UDFN-14-EP(4x3)

ZXLD1320DCATC from Diodes Incorporated, in a UDFN-14-EP(4x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ADJ input Adjust input: leave floating or connect to VREF for 100% output current, drive with 50mV<VADJ<VREF DC for 10% to 100%, drive with ~200Hz PWM for brightness control, or pull below 28mV to enter standby.
2 BIAS passive Sets base current of internal switch transistor: short to ground for maximum base drive, or connect resistor RBIAS to ground to reduce base drive current.
3 CFB bidirectional Control input/output for feedback control loop; connect a 10nF capacitor to ground for loop compensation.
4 POK output Power OK flag output that is high during normal operation and switches low if the switch remains on for more than 500µs (nom).
5 ISENSE input Switch peak current sense pin; connect resistor Rsense to ground to define peak switch current ISWPEAK = 0.05/RS.
6 EMITTER1 passive Switch emitter; connect both emitter pins to the top of RSENSE to sense emitter current.
7 EMITTER2 passive Switch emitter; connect both emitter pins to the top of RSENSE to sense emitter current.
8 COLLECTOR2 passive Switch collector; connect both collector pins to the lower side of the coil.
9 COLLECTOR1 passive Switch collector; connect both collector pins to the lower side of the coil.
10 M_LOAD input Load side input of the high side current monitor; connect to sensing resistor RM.
11 N/C unconnected Not connected locally.
12 VIN power_in Positive supply of 4-18V to the device and sensing resistor RM; decouple to ground with a capacitor close to the device, nominal average output current = 0.1/RM.
13 TADJ input Temperature adjust input for LED thermal compensation; connect thermistor/resistor network to reduce output current above a preset temperature, or connect to VREF to disable.
14 VREF power_out Internal 0.5V reference voltage output.
15 Exposed Pad power_in Exposed pad; connect to Ground (0V).

Key specifications

Parameter Value
Manufacturer Diodes Incorporated
Package UDFN-14-EP(4x3)
Category Display Modules / LED Drivers / Display Drivers
Pins 15

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VIN 4 18 V Normal operation 5
Standby current ISTBY 12 20 µA Measured into VIN. ADJ pin grounded 5
Internal reference voltage VREF 480 500 520 mV ADJ pin floating 2.0V<VIN<18V 5
Peak switch current sense voltage VSENSE 45 55 65 mV Measured on ISENSE pin CFB pin at 0V 5
Sense input current ISENSE -15 -7 -1 µA Measured into ISENSE with pin at 0V. CFB pin at 0V 5
External dc control voltage on ADJ VADJ 50 500 mV DC brightness control mode 5
Switching threshold of ADJ pin VADJ(th) 26 28 30 mV Standby state to normal operation 5
Discharge pulse width 100% Toff(100) 0.7 1.2 1.7 µs 100% Output current 6
Discharge pulse width 10% Toff(10) 4 8 12 µs 10% Output current 6
POK flag low level output voltage VOL(POK) 0 0.4 V Output sinking 1mA 6
POK flag high level output voltage VOH(POK) 2 V 4V<VIN<18V Output sourcing 0.3µA 6
POK assertion delay time T(POK) 300 500 700 µs Switch permanently on 6
Maximum base current into switch transistor IBON(max) 30 50 70 mA 4V<VIN<18V, BIAS pin at 0V 6
Collector-Emitter breakdown voltage V(BR)CE 20 V IC=10µA 6
Supply voltage (current monitor) VMVIN 4 18 V 7
Sense voltage VMON 0 100 200 mV =V(IN), V(M_LOAD) 7
Input current M_LOAD IM_LOAD 0.08 1 µA Measured into M_LOAD pin 7
Accuracy (high-side monitor) Acc -3 3 % RM = 0.1Ω, VMON = 100mV 7
Adjust voltage (reference monitor) VADJ 0 500 mV 7
Accuracy (reference current monitor) Acc -3 3 % VADJ=500mV 7
Output current accuracy IOUT -5 5 % 4V<VIN<18V, Iout=1A, VADJ=100mV 8
Output current temperature drift TCO I(OUT) 100 200 ppm/K 4V<VIN<18V, Iout=1A, VADJ=100mV 8
Minimum Output/LED Current IOUT 1.5 A VIN>4V 8
Quiescent current Iq 1.5 mA Measured into VIN, ADJ pin floating (excluding switch base current) 5
Internal reference temperature coefficient TCO(REF) 50 ppm/K 5
Maximum operating frequency fLXmax 600 KHz 6
Average continuous switch current ISW 1.5 A Measured under pulse conditions 6
Collector-Emitter saturation voltage VCE(sat) 50 mV IC=0.1A, IB=10mA 6
Collector-Emitter saturation voltage VCE(sat) 120 mV IC=2A, IB=50mA 6
Upper threshold voltage TADJ VTADJH 75 mV Onset of output current reduction (VTADJ falling) 7
Lower threshold voltage TADJ VTADJL 50 mV Output current reduced to <10% of set value (VTADJ falling) 7
Supply voltage VIN -0.3 18 V Relative to GND 3
POK voltage POK -0.3 V Max VIN + 0.3V 3
Continuous sense voltage M_VIN, M_LOAD -0.3 5 V 3
Collector-Base voltage VCBO 20 V 3
Collector-Emitter voltage VCEO 20 V 3
Peak pulse current ICM 3 A Pulse Width = 300µs. Duty Cycle<=2% 3
Continuous Collector current IC 1.5 A 3
Operating temperature Top -40 125 °C 3
Storage temperature Tst -55 150 °C 3
Junction temperature Tj -40 150 °C 3
Package power dissipation Ptot 1.5 W DFN-14 with Exposed Pad, Tamb = 70°C 3
Junction to ambient thermal resistance RJA 53 °C/W DFN-14, nominal value 3

CAD (KiCad official)

  • Symbol: ZXLD1320DCATC
  • Footprint: Package_DFN_QFN:DFN-14-1EP_3x4mm_P0.5mm_EP1.7x3.3mm
  • 3D model: UDFN-14-EP(4x3) (KiCad packages3D, STEP)
  • 3D model files: zxld1320dcatc-etched.step / zxld1320dcatc-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); zxld1320dcatc.step / zxld1320dcatc.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Diodes Incorporated datasheet (18 pp, sha256 9da84cf5fd627828, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF