3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownZXLD1320DCATC
Diodes Incorporated · LED Drivers · UDFN-14-EP(4x3)
ZXLD1320DCATC from Diodes Incorporated, in a UDFN-14-EP(4x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ADJ | input | Adjust input: leave floating or connect to VREF for 100% output current, drive with 50mV<VADJ<VREF DC for 10% to 100%, drive with ~200Hz PWM for brightness control, or pull below 28mV to enter standby. |
| 2 | BIAS | passive | Sets base current of internal switch transistor: short to ground for maximum base drive, or connect resistor RBIAS to ground to reduce base drive current. |
| 3 | CFB | bidirectional | Control input/output for feedback control loop; connect a 10nF capacitor to ground for loop compensation. |
| 4 | POK | output | Power OK flag output that is high during normal operation and switches low if the switch remains on for more than 500µs (nom). |
| 5 | ISENSE | input | Switch peak current sense pin; connect resistor Rsense to ground to define peak switch current ISWPEAK = 0.05/RS. |
| 6 | EMITTER1 | passive | Switch emitter; connect both emitter pins to the top of RSENSE to sense emitter current. |
| 7 | EMITTER2 | passive | Switch emitter; connect both emitter pins to the top of RSENSE to sense emitter current. |
| 8 | COLLECTOR2 | passive | Switch collector; connect both collector pins to the lower side of the coil. |
| 9 | COLLECTOR1 | passive | Switch collector; connect both collector pins to the lower side of the coil. |
| 10 | M_LOAD | input | Load side input of the high side current monitor; connect to sensing resistor RM. |
| 11 | N/C | unconnected | Not connected locally. |
| 12 | VIN | power_in | Positive supply of 4-18V to the device and sensing resistor RM; decouple to ground with a capacitor close to the device, nominal average output current = 0.1/RM. |
| 13 | TADJ | input | Temperature adjust input for LED thermal compensation; connect thermistor/resistor network to reduce output current above a preset temperature, or connect to VREF to disable. |
| 14 | VREF | power_out | Internal 0.5V reference voltage output. |
| 15 | Exposed Pad | power_in | Exposed pad; connect to Ground (0V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | UDFN-14-EP(4x3) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VIN | 4 | 18 | V | Normal operation | 5 | |
| Standby current | ISTBY | 12 | 20 | µA | Measured into VIN. ADJ pin grounded | 5 | |
| Internal reference voltage | VREF | 480 | 500 | 520 | mV | ADJ pin floating 2.0V<VIN<18V | 5 |
| Peak switch current sense voltage | VSENSE | 45 | 55 | 65 | mV | Measured on ISENSE pin CFB pin at 0V | 5 |
| Sense input current | ISENSE | -15 | -7 | -1 | µA | Measured into ISENSE with pin at 0V. CFB pin at 0V | 5 |
| External dc control voltage on ADJ | VADJ | 50 | 500 | mV | DC brightness control mode | 5 | |
| Switching threshold of ADJ pin | VADJ(th) | 26 | 28 | 30 | mV | Standby state to normal operation | 5 |
| Discharge pulse width 100% | Toff(100) | 0.7 | 1.2 | 1.7 | µs | 100% Output current | 6 |
| Discharge pulse width 10% | Toff(10) | 4 | 8 | 12 | µs | 10% Output current | 6 |
| POK flag low level output voltage | VOL(POK) | 0 | 0.4 | V | Output sinking 1mA | 6 | |
| POK flag high level output voltage | VOH(POK) | 2 | V | 4V<VIN<18V Output sourcing 0.3µA | 6 | ||
| POK assertion delay time | T(POK) | 300 | 500 | 700 | µs | Switch permanently on | 6 |
| Maximum base current into switch transistor | IBON(max) | 30 | 50 | 70 | mA | 4V<VIN<18V, BIAS pin at 0V | 6 |
| Collector-Emitter breakdown voltage | V(BR)CE | 20 | V | IC=10µA | 6 | ||
| Supply voltage (current monitor) | VMVIN | 4 | 18 | V | 7 | ||
| Sense voltage | VMON | 0 | 100 | 200 | mV | =V(IN), V(M_LOAD) | 7 |
| Input current M_LOAD | IM_LOAD | 0.08 | 1 | µA | Measured into M_LOAD pin | 7 | |
| Accuracy (high-side monitor) | Acc | -3 | 3 | % | RM = 0.1Ω, VMON = 100mV | 7 | |
| Adjust voltage (reference monitor) | VADJ | 0 | 500 | mV | 7 | ||
| Accuracy (reference current monitor) | Acc | -3 | 3 | % | VADJ=500mV | 7 | |
| Output current accuracy | IOUT | -5 | 5 | % | 4V<VIN<18V, Iout=1A, VADJ=100mV | 8 | |
| Output current temperature drift | TCO I(OUT) | 100 | 200 | ppm/K | 4V<VIN<18V, Iout=1A, VADJ=100mV | 8 | |
| Minimum Output/LED Current | IOUT | 1.5 | A | VIN>4V | 8 | ||
| Quiescent current | Iq | 1.5 | mA | Measured into VIN, ADJ pin floating (excluding switch base current) | 5 | ||
| Internal reference temperature coefficient | TCO(REF) | 50 | ppm/K | 5 | |||
| Maximum operating frequency | fLXmax | 600 | KHz | 6 | |||
| Average continuous switch current | ISW | 1.5 | A | Measured under pulse conditions | 6 | ||
| Collector-Emitter saturation voltage | VCE(sat) | 50 | mV | IC=0.1A, IB=10mA | 6 | ||
| Collector-Emitter saturation voltage | VCE(sat) | 120 | mV | IC=2A, IB=50mA | 6 | ||
| Upper threshold voltage TADJ | VTADJH | 75 | mV | Onset of output current reduction (VTADJ falling) | 7 | ||
| Lower threshold voltage TADJ | VTADJL | 50 | mV | Output current reduced to <10% of set value (VTADJ falling) | 7 | ||
| Supply voltage | VIN | -0.3 | 18 | V | Relative to GND | 3 | |
| POK voltage | POK | -0.3 | V | Max VIN + 0.3V | 3 | ||
| Continuous sense voltage | M_VIN, M_LOAD | -0.3 | 5 | V | 3 | ||
| Collector-Base voltage | VCBO | 20 | V | 3 | |||
| Collector-Emitter voltage | VCEO | 20 | V | 3 | |||
| Peak pulse current | ICM | 3 | A | Pulse Width = 300µs. Duty Cycle<=2% | 3 | ||
| Continuous Collector current | IC | 1.5 | A | 3 | |||
| Operating temperature | Top | -40 | 125 | °C | 3 | ||
| Storage temperature | Tst | -55 | 150 | °C | 3 | ||
| Junction temperature | Tj | -40 | 150 | °C | 3 | ||
| Package power dissipation | Ptot | 1.5 | W | DFN-14 with Exposed Pad, Tamb = 70°C | 3 | ||
| Junction to ambient thermal resistance | RJA | 53 | °C/W | DFN-14, nominal value | 3 |
CAD (KiCad official)
- Symbol:
ZXLD1320DCATC - Footprint:
Package_DFN_QFN:DFN-14-1EP_3x4mm_P0.5mm_EP1.7x3.3mm - 3D model: UDFN-14-EP(4x3) (KiCad packages3D, STEP)
- 3D model files:
zxld1320dcatc-etched.step/zxld1320dcatc-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);zxld1320dcatc.step/zxld1320dcatc.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (18 pp, sha256
9da84cf5fd627828, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).