ZD24C08A-SSGMB

{
 "schema": "adom.pads/1",
 "slug": "zd24c08a-ssgmb",
 "footprint": "SOIC-8_3.9x4.9mm_P1.27mm",
 "generated_from": {
  "footprint": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -2.475,
   -1.905
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4"
 },
 "pad_count": 8,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "A2",
   "type": "input",
   "description": "Hardware device address input bit A2. Tie directly to VCC or GND to select one of two device addresses on the I2C bus. Internally pulled down to GND (weakly) when left floating; Zetta recommends driving to a known state.",
   "is_pin1": true,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "NC",
   "type": "unconnected",
   "description": "Not internally bonded. May be left floating or tied to GND. (Corresponds to A1 on smaller-density variants; unused on the 8K device because that address bit is repurposed as page-select P1.)",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "NC",
   "type": "unconnected",
   "description": "Not internally bonded. May be left floating or tied to GND. (Corresponds to A0 on smaller-density variants; unused on the 8K device because that address bit is repurposed as page-select P0.)",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "GND",
   "type": "power_in",
   "description": "Ground reference for the power supply. Connect to system ground.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "SDA",
   "type": "bidirectional",
   "description": "I2C serial data. Open-drain bidirectional line; must be pulled high with an external resistor (not exceeding 10 kOhm). May be wire-ORed with other open-drain/open-collector devices on the same bus.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "SCL",
   "type": "input",
   "description": "I2C serial clock input from the bus master. Data on SDA is latched on the rising edge and output on the falling edge of SCL. Must be forced high when the bus is idle or pulled high through an external resistor.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "7",
   "name": "WP",
   "type": "input",
   "description": "Write Protect (active high). Tie to GND for normal read/write operation; tie to VCC to inhibit all writes to the full memory array. Internally pulled down to GND when left floating; Zetta recommends driving to a known state.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "8",
   "name": "VCC",
   "type": "power_in",
   "description": "Device power supply. Operations at invalid VCC voltages may produce spurious results and should not be attempted.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}