main
Ray
Publish 0.1.0
efc4cda
XW01D
Sam&wing · Touch Sensors · SO-8
XW01D from Sam&wing, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VSS | power_in | Negative power supply pin, serving as the ground reference for the device. |
| 2 | VREG | output | Internal reference source output, which the datasheet specifies is decoupled with a 4.7 nF capacitor. |
| 3 | SEN | bidirectional | Sensitivity capacitor pin, where a 15 pF to 100 pF capacitor sets sensitivity and a smaller value gives higher sensitivity. |
| 4 | CR | bidirectional | Detection reference value setting pin, used with the reference capacitor shown in the application circuit. |
| 5 | CX | bidirectional | Sensing antenna pin, connected in series with a 3 kΩ resistor per the datasheet. |
| 6 | OUT | output | Key output pin with high-impedance and low-level states, intended for use with an external pull-up resistor to VCC (open-drain, low-level sink current rated 10 mA at VCC=5 V). |
| 7 | FUN | input | Function setting pin: leaving it floating selects lower-sensitivity operation for slow changes such as water level detection, while tying it to VCC selects higher-sensitivity self-calibrating operation such as toilet-lid body detection. |
| 8 | VCC | power_in | Positive supply voltage input, with an operating range of 2.5 V to 6.5 V and absolute maximum of -0.3 V to +6.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sam&wing |
| Package | SO-8 |
| Category | Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 工作电压 | Vcc | 2.5 | 6.5 | V | 3 | ||
| 电源电压 (额定值) | -0.3 | 6.5 | V | 3 | |||
| 工作温度 (额定值) | -40 | 85 | ºC | 3 | |||
| 存储温度 (额定值) | -50 | 150 | ºC | 3 | |||
| 管脚最大电流 (额定值) | -20 | 20 | mA | 3 | |||
| 管脚电压 (额定值) | -0.3 | V | upper limit printed as (Vcc+0.3) | 3 | |||
| 电流消耗 | Idd | 810 | uA | VCC=5.0V | 3 | ||
| 电流消耗 | Idd | 460 | uA | VCC=3.0V | 3 | ||
| 电流消耗 (SLEEP) | Idd | 70 | uA | VCC=5.0V, &SLEEP | 3 | ||
| 电流消耗 (SLEEP) | Idd | 38 | uA | VCC=3.0V, &SLEEP | 3 | ||
| 上电稳定时间 | Tini | 120 | ms | 3 | |||
| 输出阻抗 (开漏输出) | Zo | 50 | Ohm | 低电平 (output low) | 3 | ||
| 输出灌电流 | Isk | 10 | mA | VCC=5V | 3 | ||
| 最小检测电容 | delta_CX | 0.2 | pF | CSEN=15pf | 3 | ||
| 采样周期 | Tsi | 2.7 | ms | 正常工作状态 (normal operating state) | 3 | ||
| ESD HBM | 8000 | V | H.B.M POS/NEG, reference VCC | 3 | |||
| ESD MM | 500 | V | M.M POS/NEG, reference VCC | 3 |
CAD (KiCad official)
- Symbol:
XW01D - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
xw01d-etched.step/xw01d-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xw01d.step/xw01d.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sam&wing datasheet (4 pp, sha256
91bcfad8f80d1073, retrieved 2026-11-12, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# XW01D
**Sam&wing** · Touch Sensors · SO-8
XW01D from Sam&wing, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VSS | power_in | Negative power supply pin, serving as the ground reference for the device. |
| 2 | VREG | output | Internal reference source output, which the datasheet specifies is decoupled with a 4.7 nF capacitor. |
| 3 | SEN | bidirectional | Sensitivity capacitor pin, where a 15 pF to 100 pF capacitor sets sensitivity and a smaller value gives higher sensitivity. |
| 4 | CR | bidirectional | Detection reference value setting pin, used with the reference capacitor shown in the application circuit. |
| 5 | CX | bidirectional | Sensing antenna pin, connected in series with a 3 kΩ resistor per the datasheet. |
| 6 | OUT | output | Key output pin with high-impedance and low-level states, intended for use with an external pull-up resistor to VCC (open-drain, low-level sink current rated 10 mA at VCC=5 V). |
| 7 | FUN | input | Function setting pin: leaving it floating selects lower-sensitivity operation for slow changes such as water level detection, while tying it to VCC selects higher-sensitivity self-calibrating operation such as toilet-lid body detection. |
| 8 | VCC | power_in | Positive supply voltage input, with an operating range of 2.5 V to 6.5 V and absolute maximum of -0.3 V to +6.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sam&wing |
| Package | SO-8 |
| Category | Sensors |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 工作电压 | Vcc | 2.5 | | 6.5 | V | | 3 |
| 电源电压 (额定值) | | -0.3 | | 6.5 | V | | 3 |
| 工作温度 (额定值) | | -40 | | 85 | ºC | | 3 |
| 存储温度 (额定值) | | -50 | | 150 | ºC | | 3 |
| 管脚最大电流 (额定值) | | -20 | | 20 | mA | | 3 |
| 管脚电压 (额定值) | | -0.3 | | | V | upper limit printed as (Vcc+0.3) | 3 |
| 电流消耗 | Idd | | | 810 | uA | VCC=5.0V | 3 |
| 电流消耗 | Idd | | | 460 | uA | VCC=3.0V | 3 |
| 电流消耗 (SLEEP) | Idd | | | 70 | uA | VCC=5.0V, &SLEEP | 3 |
| 电流消耗 (SLEEP) | Idd | | | 38 | uA | VCC=3.0V, &SLEEP | 3 |
| 上电稳定时间 | Tini | | | 120 | ms | | 3 |
| 输出阻抗 (开漏输出) | Zo | | | 50 | Ohm | 低电平 (output low) | 3 |
| 输出灌电流 | Isk | 10 | | | mA | VCC=5V | 3 |
| 最小检测电容 | delta_CX | | | 0.2 | pF | CSEN=15pf | 3 |
| 采样周期 | Tsi | | 2.7 | | ms | 正常工作状态 (normal operating state) | 3 |
| ESD HBM | | | | 8000 | V | H.B.M POS/NEG, reference VCC | 3 |
| ESD MM | | | | 500 | V | M.M POS/NEG, reference VCC | 3 |
## CAD (KiCad official)
- Symbol: `XW01D`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `xw01d-etched.step` / `xw01d-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `xw01d.step` / `xw01d.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Sam&wing datasheet](docs/xw01d-datasheet.pdf) (4 pp, sha256 `91bcfad8f80d1073`, retrieved 2026-11-12, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/xw01d-datasheet.pdf)