main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers xw01d: viewers rendered from the public page · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 8 pins · Ray
xw01d-etched.glb Publish 0.1.0 · Ray
xw01d-etched.step xw01d: factory component page (tier=lcsc) · Ray
xw01d-hero.glb xw01d: hero GLB from the etched model (keeps the MPN mark) · Ray
xw01d-hero.overlay.json xw01d: hero GLB from the etched model (keeps the MPN mark) · Ray
xw01d.glb Publish 0.1.0 · Ray
xw01d.kicad_mod Publish 0.1.0 · Ray
xw01d.kicad_sym Publish 0.1.0 · Ray
xw01d.lbr Publish 0.1.0 · Ray
xw01d.step Publish 0.1.0 · Ray

XW01D

Sam&wing · Touch Sensors · SO-8

XW01D from Sam&wing, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VSS power_in Negative power supply pin, serving as the ground reference for the device.
2 VREG output Internal reference source output, which the datasheet specifies is decoupled with a 4.7 nF capacitor.
3 SEN bidirectional Sensitivity capacitor pin, where a 15 pF to 100 pF capacitor sets sensitivity and a smaller value gives higher sensitivity.
4 CR bidirectional Detection reference value setting pin, used with the reference capacitor shown in the application circuit.
5 CX bidirectional Sensing antenna pin, connected in series with a 3 kΩ resistor per the datasheet.
6 OUT output Key output pin with high-impedance and low-level states, intended for use with an external pull-up resistor to VCC (open-drain, low-level sink current rated 10 mA at VCC=5 V).
7 FUN input Function setting pin: leaving it floating selects lower-sensitivity operation for slow changes such as water level detection, while tying it to VCC selects higher-sensitivity self-calibrating operation such as toilet-lid body detection.
8 VCC power_in Positive supply voltage input, with an operating range of 2.5 V to 6.5 V and absolute maximum of -0.3 V to +6.5 V.

Key specifications

Parameter Value
Manufacturer Sam&wing
Package SO-8
Category Sensors
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
工作电压 Vcc 2.5 6.5 V 3
电源电压 (额定值) -0.3 6.5 V 3
工作温度 (额定值) -40 85 ºC 3
存储温度 (额定值) -50 150 ºC 3
管脚最大电流 (额定值) -20 20 mA 3
管脚电压 (额定值) -0.3 V upper limit printed as (Vcc+0.3) 3
电流消耗 Idd 810 uA VCC=5.0V 3
电流消耗 Idd 460 uA VCC=3.0V 3
电流消耗 (SLEEP) Idd 70 uA VCC=5.0V, &SLEEP 3
电流消耗 (SLEEP) Idd 38 uA VCC=3.0V, &SLEEP 3
上电稳定时间 Tini 120 ms 3
输出阻抗 (开漏输出) Zo 50 Ohm 低电平 (output low) 3
输出灌电流 Isk 10 mA VCC=5V 3
最小检测电容 delta_CX 0.2 pF CSEN=15pf 3
采样周期 Tsi 2.7 ms 正常工作状态 (normal operating state) 3
ESD HBM 8000 V H.B.M POS/NEG, reference VCC 3
ESD MM 500 V M.M POS/NEG, reference VCC 3

CAD (KiCad official)

  • Symbol: XW01D
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SO-8 (KiCad packages3D, STEP)
  • 3D model files: xw01d-etched.step / xw01d-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); xw01d.step / xw01d.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Sam&wing datasheet (4 pp, sha256 91bcfad8f80d1073, retrieved 2026-11-12, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF