main
Ray
Publish 0.1.0
d67a871
XT26Q18DWSIGA
XTX · NAND FLASH · WSON-8-EP(6x8)
XT26Q18DWSIGA from XTX, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input; when high the device is deselected and the SIO outputs are high impedance, and after power-up CS# must go high to low before a new instruction is accepted. |
| 2 | SO (SIO1) | bidirectional | Serial Data Output in standard SPI, shifted out on the falling edge of CLK; it becomes the bidirectional SIO1 data line during Dual and Quad commands. |
| 3 | WP# (SIO2) | bidirectional | Write Protect input that, when driven low while BRWD is set, prevents the block lock bits from being altered; it becomes the SIO2 data line in Quad mode, and the pin is internally pulled up to VCC. |
| 4 | VSS | power_in | Ground reference for the device. |
| 5 | SI (SIO0) | bidirectional | Serial Data Input in standard SPI, latched on the rising edge of CLK; it becomes the bidirectional SIO0 data line during Dual and Quad commands. |
| 6 | SCLK | input | Serial clock input that provides the synchronization reference for the SPI interface, with inputs latched on the rising edge and data output changing after the falling edge; SPI modes 0 (0,0) and 3 (1,1) are supported. |
| 7 | SIO3 | bidirectional | Data line SIO3 used by Quad SPI command sets; for Standard and Dual SPI command sets it must be kept at a high level. |
| 8 | VCC | power_in | Power supply input; the device operates from a single supply of 1.7V to 1.95V. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XTX |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature | -40 | 85 | °C | 46 | |||
| Storage Temperature | -65 | 150 | °C | 46 | |||
| VCC | VCC | -0.3 | 2.25 | V | 46 | ||
| Voltage on I/O Pin with Respect to Ground | -0.3 | V | 46 | ||||
| Electrostatic Discharge Voltage, Human Body Model | -4000 | 4000 | V | JS-001-2017 (R=1500 ohms, C=100pF) | 46 | ||
| Electrostatic Discharge Voltage, Charge Device Model | 1000 | V | JS-002-2018 | 46 | |||
| Latch-Up Input Voltage with respect to GND on all power pins | 1.5 | V | VCC = VCCmax, one pin at a time (JEDEC JESD78) | 46 | |||
| Latch-Up Input Current on all non-power pins | -200 | 200 | mA | VCC = VCCmax, one pin at a time (JEDEC JESD78) | 46 | ||
| Input Capacitance | CIN | 6 | pF | VIN = 0V | 46 | ||
| Output Capacitance | COUT | 8 | pF | VOUT = 0V | 46 | ||
| Operating Temperature (recommended range) | TA | -40 | 85 | °C | 48 | ||
| Supply Voltage | VCC | 1.7 | 1.95 | V | 48 | ||
| VCC (min) to CS# Low | tVSL | 3 | ms | 47 | |||
| Write Inhibit Voltage | VWI | 1.6 | V | 47 | |||
| Input Leakage Current | ILI | -2 | 2 | µA | 48 | ||
| Output Leakage Current | ILO | -2 | 2 | µA | 48 | ||
| Standby Current | ICC1 | 15 | 120 | µA | CS# = VCC, VIN = VSS or VCC | 48 | |
| Read Current | ICC2 | 20 | 40 | mA | CLK=0.1VCC/0.9VCC, FCLK=108MHz | 48 | |
| Program Current | 18 | 40 | mA | 48 | |||
| Erase Current | 18 | 40 | mA | 48 | |||
| Input Low Voltage | VIL | -0.3 | V | 48 | |||
| Output Low Voltage | VOL | 0.4 | V | IOL = 1.6mA | 48 | ||
| Serial Clock Frequency | fC | 108 | MHz | for all command | 50 | ||
| Serial Clock High Time | tCH | 3.75 | ns | 50 | |||
| Serial Clock Low Time | tCL | 3.75 | ns | 50 | |||
| Serial Clock Rise Time (Slew Rate) | tCLCH | 0.1 | V/ns | 50 | |||
| Serial Clock Fall Time (Slew Rate) | tCHCL | 0.1 | V/ns | 50 | |||
| CS# Active Setup Time | tSLCH | 10 | ns | 50 | |||
| CS# Active Hold Time | tCHSH | 2.5 | ns | 50 | |||
| CS# Not Active Setup Time | tSHCH | 2.5 | ns | 50 | |||
| CS# Not Active Hold Time | tCHSL | 2.5 | ns | 50 | |||
| CS# High Time | tSHSL/tCS | 100 | ns | 50 | |||
| Output Disable Time | tSHQZ | 15 | ns | 50 | |||
| Output Hold Time | tCLQX | 2 | ns | CL=30pF | 50 | ||
| Clock Low to Output Valid | tCLQV | 8 | ns | CL=30pF | 50 | ||
| Clock Low to Output Valid | tCLQV | 7 | ns | CL=15pF | 50 | ||
| Data In Setup Time | tDVCH | 4 | ns | 50 | |||
| Data In Hold Time | tCHDX | 1.75 | ns | 50 | |||
| WP# Setup Time before CS# Low | tWHSL | 20 | ns | 50 | |||
| WP# Hold Time after CS# High | tSHWL | 100 | ns | 50 | |||
| CS# High to Next Command After Reset (FFh) from Idle/Program/Read | tRST | 50 | µs | from Idle/Program/Read | 51 | ||
| CS# High to Next Command After Reset (FFh) from Erase | tRST | 550 | µs | from Erase | 51 | ||
| Page Read From Array (with ECC) | tRD | 210 | 270 | µs | High speed Mode Disable | 51 | |
| Page Read From Array (without ECC) | tRD | 210 | 240 | µs | High speed Mode Disable | 51 | |
| Page Program | tPROG | 400 | 750 | µs | 51 | ||
| Block Erase | tERS | 3.5 | 10 | ms | 51 |
CAD (KiCad official)
- Symbol:
XT26Q18DWSIGA - Footprint:
Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm - 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
xt26q18dwsiga-etched.step/xt26q18dwsiga-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xt26q18dwsiga.step/xt26q18dwsiga.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XTX datasheet (56 pp, sha256
1df41f8bbd9ef28a, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# XT26Q18DWSIGA
**XTX** · NAND FLASH · WSON-8-EP(6x8)
XT26Q18DWSIGA from XTX, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input; when high the device is deselected and the SIO outputs are high impedance, and after power-up CS# must go high to low before a new instruction is accepted. |
| 2 | SO (SIO1) | bidirectional | Serial Data Output in standard SPI, shifted out on the falling edge of CLK; it becomes the bidirectional SIO1 data line during Dual and Quad commands. |
| 3 | WP# (SIO2) | bidirectional | Write Protect input that, when driven low while BRWD is set, prevents the block lock bits from being altered; it becomes the SIO2 data line in Quad mode, and the pin is internally pulled up to VCC. |
| 4 | VSS | power_in | Ground reference for the device. |
| 5 | SI (SIO0) | bidirectional | Serial Data Input in standard SPI, latched on the rising edge of CLK; it becomes the bidirectional SIO0 data line during Dual and Quad commands. |
| 6 | SCLK | input | Serial clock input that provides the synchronization reference for the SPI interface, with inputs latched on the rising edge and data output changing after the falling edge; SPI modes 0 (0,0) and 3 (1,1) are supported. |
| 7 | SIO3 | bidirectional | Data line SIO3 used by Quad SPI command sets; for Standard and Dual SPI command sets it must be kept at a high level. |
| 8 | VCC | power_in | Power supply input; the device operates from a single supply of 1.7V to 1.95V. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XTX |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature | | -40 | | 85 | °C | | 46 |
| Storage Temperature | | -65 | | 150 | °C | | 46 |
| VCC | VCC | -0.3 | | 2.25 | V | | 46 |
| Voltage on I/O Pin with Respect to Ground | | -0.3 | | | V | | 46 |
| Electrostatic Discharge Voltage, Human Body Model | | -4000 | | 4000 | V | JS-001-2017 (R=1500 ohms, C=100pF) | 46 |
| Electrostatic Discharge Voltage, Charge Device Model | | 1000 | | | V | JS-002-2018 | 46 |
| Latch-Up Input Voltage with respect to GND on all power pins | | 1.5 | | | V | VCC = VCCmax, one pin at a time (JEDEC JESD78) | 46 |
| Latch-Up Input Current on all non-power pins | | -200 | | 200 | mA | VCC = VCCmax, one pin at a time (JEDEC JESD78) | 46 |
| Input Capacitance | CIN | | | 6 | pF | VIN = 0V | 46 |
| Output Capacitance | COUT | | | 8 | pF | VOUT = 0V | 46 |
| Operating Temperature (recommended range) | TA | -40 | | 85 | °C | | 48 |
| Supply Voltage | VCC | 1.7 | | 1.95 | V | | 48 |
| VCC (min) to CS# Low | tVSL | 3 | | | ms | | 47 |
| Write Inhibit Voltage | VWI | 1.6 | | | V | | 47 |
| Input Leakage Current | ILI | -2 | | 2 | µA | | 48 |
| Output Leakage Current | ILO | -2 | | 2 | µA | | 48 |
| Standby Current | ICC1 | | 15 | 120 | µA | CS# = VCC, VIN = VSS or VCC | 48 |
| Read Current | ICC2 | | 20 | 40 | mA | CLK=0.1VCC/0.9VCC, FCLK=108MHz | 48 |
| Program Current | | | 18 | 40 | mA | | 48 |
| Erase Current | | | 18 | 40 | mA | | 48 |
| Input Low Voltage | VIL | -0.3 | | | V | | 48 |
| Output Low Voltage | VOL | | | 0.4 | V | IOL = 1.6mA | 48 |
| Serial Clock Frequency | fC | | | 108 | MHz | for all command | 50 |
| Serial Clock High Time | tCH | 3.75 | | | ns | | 50 |
| Serial Clock Low Time | tCL | 3.75 | | | ns | | 50 |
| Serial Clock Rise Time (Slew Rate) | tCLCH | | | 0.1 | V/ns | | 50 |
| Serial Clock Fall Time (Slew Rate) | tCHCL | | | 0.1 | V/ns | | 50 |
| CS# Active Setup Time | tSLCH | 10 | | | ns | | 50 |
| CS# Active Hold Time | tCHSH | 2.5 | | | ns | | 50 |
| CS# Not Active Setup Time | tSHCH | 2.5 | | | ns | | 50 |
| CS# Not Active Hold Time | tCHSL | 2.5 | | | ns | | 50 |
| CS# High Time | tSHSL/tCS | 100 | | | ns | | 50 |
| Output Disable Time | tSHQZ | | | 15 | ns | | 50 |
| Output Hold Time | tCLQX | 2 | | | ns | CL=30pF | 50 |
| Clock Low to Output Valid | tCLQV | | | 8 | ns | CL=30pF | 50 |
| Clock Low to Output Valid | tCLQV | | | 7 | ns | CL=15pF | 50 |
| Data In Setup Time | tDVCH | 4 | | | ns | | 50 |
| Data In Hold Time | tCHDX | 1.75 | | | ns | | 50 |
| WP# Setup Time before CS# Low | tWHSL | 20 | | | ns | | 50 |
| WP# Hold Time after CS# High | tSHWL | 100 | | | ns | | 50 |
| CS# High to Next Command After Reset (FFh) from Idle/Program/Read | tRST | | | 50 | µs | from Idle/Program/Read | 51 |
| CS# High to Next Command After Reset (FFh) from Erase | tRST | | | 550 | µs | from Erase | 51 |
| Page Read From Array (with ECC) | tRD | | 210 | 270 | µs | High speed Mode Disable | 51 |
| Page Read From Array (without ECC) | tRD | | 210 | 240 | µs | High speed Mode Disable | 51 |
| Page Program | tPROG | | 400 | 750 | µs | | 51 |
| Block Erase | tERS | | 3.5 | 10 | ms | | 51 |
## CAD (KiCad official)
- Symbol: `XT26Q18DWSIGA`
- Footprint: `Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm`
- 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files: `xt26q18dwsiga-etched.step` / `xt26q18dwsiga-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `xt26q18dwsiga.step` / `xt26q18dwsiga.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [XTX datasheet](docs/xt26q18dwsiga-datasheet.pdf) (56 pp, sha256 `1df41f8bbd9ef28a`, retrieved 2026-10-28, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/xt26q18dwsiga-datasheet.pdf)