main
Ray
Publish 0.1.0
71d0e92
XR16M752IM48-F
MaxLinear · UART · TQFP-48(7x7)
XR16M752IM48-F from MaxLinear, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D5 | bidirectional | Data bus line 5 (bidirectional). |
| 2 | D6 | bidirectional | Data bus line 6 (bidirectional). |
| 3 | D7 | bidirectional | Data bus line 7 (bidirectional). |
| 4 | RXB | input | UART channel B receive data or infrared receive data; must idle HIGH, and if unused tie to VCC or pull high via 100k ohm. |
| 5 | RXA | input | UART channel A receive data or infrared receive data; must idle HIGH, and if unused tie to VCC or pull high via 100k ohm. |
| 6 | TXRDYB# | output | UART channel B transmitter ready (active low), showing TX FIFO/THR status; leave unconnected if not used. |
| 7 | TXA | output | UART channel A transmit data or infrared encoder data; HIGH during reset or idle in standard mode; leave unconnected if not used. |
| 8 | TXB | output | UART channel B transmit data or infrared encoder data; HIGH during reset or idle in standard mode; leave unconnected if not used. |
| 9 | OP2B# | output | Output Port 2 channel B, set through MCR[3] (LOW when MCR[3]=1, HIGH when 0); should not be used as a general output if INTB is used. |
| 10 | CSA# | input | Chip select A (active low) to enable channel A in Intel mode. |
| 11 | CSB# | input | Chip select B (active low) to enable channel B in Intel mode. |
| 12 | NC | unconnected | No connection. |
| 13 | XTAL1 | input | Crystal or external clock input; not 5V tolerant, maximum at the pin is VCC. |
| 14 | XTAL2 | output | Crystal or buffered clock output. |
| 15 | IOW# | input | Write strobe (active low) in Intel mode; rising edge transfers the data byte on the data bus to the internal register addressed. |
| 16 | CDB# | input | UART channel B carrier-detect (active low) or general purpose input; connect to VCC or GND when not used. |
| 17 | GND | power_in | Power supply common, ground. |
| 18 | RXRDYB# | output | UART channel B receiver ready (active low), showing RX FIFO/RHR status; leave unconnected if not used. |
| 19 | IOR# | input | Read strobe (active low) in Intel mode; falling edge starts an internal read cycle that puts the addressed register byte on the data bus. |
| 20 | DSRB# | input | UART channel B data-set-ready (active low) or general purpose input; connect to VCC or GND when not used. |
| 21 | RIB# | input | UART channel B ring-indicator (active low) or general purpose input; connect to VCC or GND when not used. |
| 22 | RTSB# | output | UART channel B request-to-send (active low) or general purpose output; must be asserted before using auto RTS flow control; also auto RS485 direction control. |
| 23 | CTSB# | input | UART channel B clear-to-send (active low) or general purpose input for auto CTS flow control; connect to VCC or GND when not used. |
| 24 | NC | unconnected | Not connected on the XR16M752 (pin is 16/68# only on the XR68M752). |
| 25 | NC | unconnected | No connection. |
| 26 | A2 | input | Address line 2; with A1 and A0 selects one of the internal registers in UART channel A/B. |
| 27 | A1 | input | Address line 1; with A2 and A0 selects one of the internal registers in UART channel A/B. |
| 28 | A0 | input | Address line 0; with A2 and A1 selects one of the internal registers in UART channel A/B. |
| 29 | INTB | output | Channel B interrupt output in Intel mode, set active or three-state via MCR[3]. |
| 30 | INTA | output | Channel A interrupt output in Intel mode, set active or three-state via MCR[3]. |
| 31 | RXRDYA# | output | UART channel A receiver ready (active low), showing RX FIFO/RHR status; leave unconnected if not used. |
| 32 | OP2A# | output | Output Port 2 channel A, set through MCR[3] (LOW when MCR[3]=1, HIGH when 0); should not be used as a general output if INTA is used. |
| 33 | RTSA# | output | UART channel A request-to-send (active low) or general purpose output; must be asserted before using auto RTS flow control; also auto RS485 direction control. |
| 34 | DTRA# | output | UART channel A data-terminal-ready (active low) or general purpose output; leave unconnected if not used. |
| 35 | DTRB# | output | UART channel B data-terminal-ready (active low) or general purpose output; leave unconnected if not used. |
| 36 | RESET | input | Active high reset in Intel mode; a 40 ns minimum pulse resets internal registers and outputs of channels A and B. |
| 37 | NC | unconnected | No connection. |
| 38 | CTSA# | input | UART channel A clear-to-send (active low) or general purpose input for auto CTS flow control; connect to VCC or GND when not used. |
| 39 | DSRA# | input | UART channel A data-set-ready (active low) or general purpose input; connect to VCC or GND when not used. |
| 40 | CDA# | input | UART channel A carrier-detect (active low) or general purpose input; connect to VCC or GND when not used. |
| 41 | RIA# | input | UART channel A ring-indicator (active low) or general purpose input; connect to VCC or GND when not used. |
| 42 | VCC | power_in | 1.62V to 3.63V power supply. |
| 43 | TXRDYA# | output | UART channel A transmitter ready (active low), showing TX FIFO/THR status; leave unconnected if not used. |
| 44 | D0 | bidirectional | Data bus line 0 (bidirectional). |
| 45 | D1 | bidirectional | Data bus line 1 (bidirectional). |
| 46 | D2 | bidirectional | Data bus line 2 (bidirectional). |
| 47 | D3 | bidirectional | Data bus line 3 (bidirectional). |
| 48 | D4 | bidirectional | Data bus line 4 (bidirectional). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | TQFP-48(7x7) |
| Category | Communication Interface Chip |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage range | VCC | 1.62 | 3.63 | V | TA = -40 to +85 C | 40 | |
| Operating temperature | TA | -40 | 85 | °C | 40 | ||
| Power supply range (abs max) | VCC | 4 | V | 40 | |||
| Voltage at any pin | -0.3 | 4 | V | GND-0.3V to 4V | 40 | ||
| Storage temperature | -65 | 150 | °C | 40 | |||
| Package dissipation | 500 | mW | 40 | ||||
| Thermal resistance junction-ambient (48-TQFP) | theta-ja | 59 | °C/W | margin of error ±15% | 40 | ||
| Thermal resistance junction-case (48-TQFP) | theta-jc | 16 | °C/W | margin of error ±15% | 40 | ||
| Clock input low level | VILCK | -0.3 | 0.3 | V | 1.8V column | 40 | |
| Clock input low level | VILCK | -0.3 | 0.6 | V | 2.5V column | 40 | |
| Clock input high level | VIHCK | 1.4 | V | 1.8V column; max VCC | 40 | ||
| Clock input high level | VIHCK | 1.8 | V | 2.5V column; max VCC | 40 | ||
| Clock input high level | VIHCK | 2.4 | V | 3.3V column; max VCC | 40 | ||
| Input low voltage | VIL | -0.3 | 0.2 | V | 1.8V column | 40 | |
| Input low voltage | VIL | -0.3 | 0.5 | V | 2.5V column | 40 | |
| Input low voltage | VIL | -0.3 | 0.8 | V | 3.3V column | 40 | |
| Input high voltage | VIH | 1.4 | V | 1.8V column; max VCC | 40 | ||
| Input high voltage | VIH | 1.8 | V | 2.5V column; max VCC | 40 | ||
| Input high voltage | VIH | 2 | V | 3.3V column; max VCC | 40 | ||
| Output low voltage | VOL | 0.4 | V | 1.8V column; IOL = 4 mA (assignment uncertain) | 40 | ||
| Output high voltage | VOH | 1.4 | V | 1.8V column; IOH = -1 mA (assignment uncertain) | 40 | ||
| Output high voltage | VOH | 1.8 | V | 2.5V column; IOH = -400 uA (assignment uncertain) | 40 | ||
| Output high voltage | VOH | 2 | V | 3.3V column; IOH = -200 uA (assignment uncertain) | 40 | ||
| Input low leakage current | IIL | -10 | 10 | uA | all voltage columns | 40 | |
| Input high leakage current | IIH | -10 | 10 | uA | all voltage columns | 40 | |
| Input pin capacitance | CIN | 5 | pF | all voltage columns | 40 | ||
| Power supply current | ICC | 0.5 | mA | 1.8V column; XTAL1 = 2 MHz | 40 | ||
| Power supply current | ICC | 1 | mA | 2.5V column; XTAL1 = 2 MHz | 40 | ||
| Power supply current | ICC | 2 | mA | 3.3V column; XTAL1 = 2 MHz | 40 | ||
| Sleep current (16 mode) | ISLEEP | 3 | uA | 1.8V column; See Test 1 | 40 | ||
| Sleep current (16 mode) | ISLEEP | 10 | uA | 2.5V column; See Test 1 | 40 | ||
| Sleep current (16 mode) | ISLEEP | 15 | uA | 3.3V column; See Test 1 | 40 | ||
| Sleep current (68 mode) | ISLEEP | 50 | uA | 1.8V column; See Test 1 | 40 | ||
| Sleep current (68 mode) | ISLEEP | 75 | uA | 2.5V column; See Test 1 | 40 | ||
| Sleep current (68 mode) | ISLEEP | 100 | uA | 3.3V column; See Test 1 | 40 | ||
| UART crystal oscillator frequency | XTAL1 | 24 | MHz | 1.8V, 2.5V and 3.3V ±10% | 41 | ||
| External clock frequency | ECLK | 32 | MHz | 1.8V ± 10% | 41 | ||
| External clock frequency | ECLK | 50 | MHz | 2.5V ± 10% | 41 | ||
| External clock frequency | ECLK | 64 | MHz | 3.3V ± 10% | 41 | ||
| Reset pulse width | TRST | 40 | ns | 1.8V, 2.5V and 3.3V ±10% | 42 |
CAD (KiCad official)
- Symbol:
XR16M752IM48-F - Footprint:
Package_QFP:TQFP-48_7x7mm_P0.5mm - 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
xr16m752im48-f-etched.step/xr16m752im48-f-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xr16m752im48-f.step/xr16m752im48-f.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MaxLinear datasheet (54 pp, sha256
bf6c3fe3dd3629d3, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# XR16M752IM48-F
**MaxLinear** · UART · TQFP-48(7x7)
XR16M752IM48-F from MaxLinear, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D5 | bidirectional | Data bus line 5 (bidirectional). |
| 2 | D6 | bidirectional | Data bus line 6 (bidirectional). |
| 3 | D7 | bidirectional | Data bus line 7 (bidirectional). |
| 4 | RXB | input | UART channel B receive data or infrared receive data; must idle HIGH, and if unused tie to VCC or pull high via 100k ohm. |
| 5 | RXA | input | UART channel A receive data or infrared receive data; must idle HIGH, and if unused tie to VCC or pull high via 100k ohm. |
| 6 | TXRDYB# | output | UART channel B transmitter ready (active low), showing TX FIFO/THR status; leave unconnected if not used. |
| 7 | TXA | output | UART channel A transmit data or infrared encoder data; HIGH during reset or idle in standard mode; leave unconnected if not used. |
| 8 | TXB | output | UART channel B transmit data or infrared encoder data; HIGH during reset or idle in standard mode; leave unconnected if not used. |
| 9 | OP2B# | output | Output Port 2 channel B, set through MCR[3] (LOW when MCR[3]=1, HIGH when 0); should not be used as a general output if INTB is used. |
| 10 | CSA# | input | Chip select A (active low) to enable channel A in Intel mode. |
| 11 | CSB# | input | Chip select B (active low) to enable channel B in Intel mode. |
| 12 | NC | unconnected | No connection. |
| 13 | XTAL1 | input | Crystal or external clock input; not 5V tolerant, maximum at the pin is VCC. |
| 14 | XTAL2 | output | Crystal or buffered clock output. |
| 15 | IOW# | input | Write strobe (active low) in Intel mode; rising edge transfers the data byte on the data bus to the internal register addressed. |
| 16 | CDB# | input | UART channel B carrier-detect (active low) or general purpose input; connect to VCC or GND when not used. |
| 17 | GND | power_in | Power supply common, ground. |
| 18 | RXRDYB# | output | UART channel B receiver ready (active low), showing RX FIFO/RHR status; leave unconnected if not used. |
| 19 | IOR# | input | Read strobe (active low) in Intel mode; falling edge starts an internal read cycle that puts the addressed register byte on the data bus. |
| 20 | DSRB# | input | UART channel B data-set-ready (active low) or general purpose input; connect to VCC or GND when not used. |
| 21 | RIB# | input | UART channel B ring-indicator (active low) or general purpose input; connect to VCC or GND when not used. |
| 22 | RTSB# | output | UART channel B request-to-send (active low) or general purpose output; must be asserted before using auto RTS flow control; also auto RS485 direction control. |
| 23 | CTSB# | input | UART channel B clear-to-send (active low) or general purpose input for auto CTS flow control; connect to VCC or GND when not used. |
| 24 | NC | unconnected | Not connected on the XR16M752 (pin is 16/68# only on the XR68M752). |
| 25 | NC | unconnected | No connection. |
| 26 | A2 | input | Address line 2; with A1 and A0 selects one of the internal registers in UART channel A/B. |
| 27 | A1 | input | Address line 1; with A2 and A0 selects one of the internal registers in UART channel A/B. |
| 28 | A0 | input | Address line 0; with A2 and A1 selects one of the internal registers in UART channel A/B. |
| 29 | INTB | output | Channel B interrupt output in Intel mode, set active or three-state via MCR[3]. |
| 30 | INTA | output | Channel A interrupt output in Intel mode, set active or three-state via MCR[3]. |
| 31 | RXRDYA# | output | UART channel A receiver ready (active low), showing RX FIFO/RHR status; leave unconnected if not used. |
| 32 | OP2A# | output | Output Port 2 channel A, set through MCR[3] (LOW when MCR[3]=1, HIGH when 0); should not be used as a general output if INTA is used. |
| 33 | RTSA# | output | UART channel A request-to-send (active low) or general purpose output; must be asserted before using auto RTS flow control; also auto RS485 direction control. |
| 34 | DTRA# | output | UART channel A data-terminal-ready (active low) or general purpose output; leave unconnected if not used. |
| 35 | DTRB# | output | UART channel B data-terminal-ready (active low) or general purpose output; leave unconnected if not used. |
| 36 | RESET | input | Active high reset in Intel mode; a 40 ns minimum pulse resets internal registers and outputs of channels A and B. |
| 37 | NC | unconnected | No connection. |
| 38 | CTSA# | input | UART channel A clear-to-send (active low) or general purpose input for auto CTS flow control; connect to VCC or GND when not used. |
| 39 | DSRA# | input | UART channel A data-set-ready (active low) or general purpose input; connect to VCC or GND when not used. |
| 40 | CDA# | input | UART channel A carrier-detect (active low) or general purpose input; connect to VCC or GND when not used. |
| 41 | RIA# | input | UART channel A ring-indicator (active low) or general purpose input; connect to VCC or GND when not used. |
| 42 | VCC | power_in | 1.62V to 3.63V power supply. |
| 43 | TXRDYA# | output | UART channel A transmitter ready (active low), showing TX FIFO/THR status; leave unconnected if not used. |
| 44 | D0 | bidirectional | Data bus line 0 (bidirectional). |
| 45 | D1 | bidirectional | Data bus line 1 (bidirectional). |
| 46 | D2 | bidirectional | Data bus line 2 (bidirectional). |
| 47 | D3 | bidirectional | Data bus line 3 (bidirectional). |
| 48 | D4 | bidirectional | Data bus line 4 (bidirectional). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | TQFP-48(7x7) |
| Category | Communication Interface Chip |
| Pins | 48 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage range | VCC | 1.62 | | 3.63 | V | TA = -40 to +85 C | 40 |
| Operating temperature | TA | -40 | | 85 | °C | | 40 |
| Power supply range (abs max) | VCC | | | 4 | V | | 40 |
| Voltage at any pin | | -0.3 | | 4 | V | GND-0.3V to 4V | 40 |
| Storage temperature | | -65 | | 150 | °C | | 40 |
| Package dissipation | | | | 500 | mW | | 40 |
| Thermal resistance junction-ambient (48-TQFP) | theta-ja | | 59 | | °C/W | margin of error ±15% | 40 |
| Thermal resistance junction-case (48-TQFP) | theta-jc | | 16 | | °C/W | margin of error ±15% | 40 |
| Clock input low level | VILCK | -0.3 | | 0.3 | V | 1.8V column | 40 |
| Clock input low level | VILCK | -0.3 | | 0.6 | V | 2.5V column | 40 |
| Clock input high level | VIHCK | 1.4 | | | V | 1.8V column; max VCC | 40 |
| Clock input high level | VIHCK | 1.8 | | | V | 2.5V column; max VCC | 40 |
| Clock input high level | VIHCK | 2.4 | | | V | 3.3V column; max VCC | 40 |
| Input low voltage | VIL | -0.3 | | 0.2 | V | 1.8V column | 40 |
| Input low voltage | VIL | -0.3 | | 0.5 | V | 2.5V column | 40 |
| Input low voltage | VIL | -0.3 | | 0.8 | V | 3.3V column | 40 |
| Input high voltage | VIH | 1.4 | | | V | 1.8V column; max VCC | 40 |
| Input high voltage | VIH | 1.8 | | | V | 2.5V column; max VCC | 40 |
| Input high voltage | VIH | 2 | | | V | 3.3V column; max VCC | 40 |
| Output low voltage | VOL | | | 0.4 | V | 1.8V column; IOL = 4 mA (assignment uncertain) | 40 |
| Output high voltage | VOH | 1.4 | | | V | 1.8V column; IOH = -1 mA (assignment uncertain) | 40 |
| Output high voltage | VOH | 1.8 | | | V | 2.5V column; IOH = -400 uA (assignment uncertain) | 40 |
| Output high voltage | VOH | 2 | | | V | 3.3V column; IOH = -200 uA (assignment uncertain) | 40 |
| Input low leakage current | IIL | -10 | | 10 | uA | all voltage columns | 40 |
| Input high leakage current | IIH | -10 | | 10 | uA | all voltage columns | 40 |
| Input pin capacitance | CIN | | | 5 | pF | all voltage columns | 40 |
| Power supply current | ICC | | | 0.5 | mA | 1.8V column; XTAL1 = 2 MHz | 40 |
| Power supply current | ICC | | | 1 | mA | 2.5V column; XTAL1 = 2 MHz | 40 |
| Power supply current | ICC | | | 2 | mA | 3.3V column; XTAL1 = 2 MHz | 40 |
| Sleep current (16 mode) | ISLEEP | | | 3 | uA | 1.8V column; See Test 1 | 40 |
| Sleep current (16 mode) | ISLEEP | | | 10 | uA | 2.5V column; See Test 1 | 40 |
| Sleep current (16 mode) | ISLEEP | | | 15 | uA | 3.3V column; See Test 1 | 40 |
| Sleep current (68 mode) | ISLEEP | | | 50 | uA | 1.8V column; See Test 1 | 40 |
| Sleep current (68 mode) | ISLEEP | | | 75 | uA | 2.5V column; See Test 1 | 40 |
| Sleep current (68 mode) | ISLEEP | | | 100 | uA | 3.3V column; See Test 1 | 40 |
| UART crystal oscillator frequency | XTAL1 | | | 24 | MHz | 1.8V, 2.5V and 3.3V ±10% | 41 |
| External clock frequency | ECLK | | | 32 | MHz | 1.8V ± 10% | 41 |
| External clock frequency | ECLK | | | 50 | MHz | 2.5V ± 10% | 41 |
| External clock frequency | ECLK | | | 64 | MHz | 3.3V ± 10% | 41 |
| Reset pulse width | TRST | 40 | | | ns | 1.8V, 2.5V and 3.3V ±10% | 42 |
## CAD (KiCad official)
- Symbol: `XR16M752IM48-F`
- Footprint: `Package_QFP:TQFP-48_7x7mm_P0.5mm`
- 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files: `xr16m752im48-f-etched.step` / `xr16m752im48-f-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `xr16m752im48-f.step` / `xr16m752im48-f.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [MaxLinear datasheet](docs/xr16m752im48-f-datasheet.pdf) (54 pp, sha256 `bf6c3fe3dd3629d3`, retrieved 2026-11-12, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/xr16m752im48-f-datasheet.pdf)