Generated by kicad-footprint-generator · KiCad file format 20260206
XL75176AP
XINLUDA · RS-485 / RS-422 ICs · DIP-8
XL75176AP from XINLUDA, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | R | output | Logic data output from the RS-485 receiver; it is high for VID ≥ 0.2 V, low for VID ≤ -0.2 V, and high impedance when the receiver is disabled (RE high). |
| 2 | RE | input | Receive enable, active low; driving RE high puts receiver output R into the high-impedance state. |
| 3 | DE | input | Driver enable, active high; when DE is low the driver differential outputs A and B are high impedance, and VIH/VIL limits for DE are 2 V / 0.8 V. |
| 4 | D | input | Logic data input to the RS-485 driver; with DE high, a high level on D drives A high and B low, and a low level drives A low and B high. |
| 5 | GND | power_in | Device ground pin; all voltages except the differential bus voltage are referenced to the network ground terminal. |
| 6 | A | bidirectional | Non-inverting RS-422/RS-485 differential bus terminal; recommended voltage range at any bus terminal is -7 V to 12 V and absolute maximum is -10 V to 15 V. |
| 7 | B | bidirectional | Inverting RS-422/RS-485 differential bus terminal; recommended voltage range at any bus terminal is -7 V to 12 V and absolute maximum is -10 V to 15 V. |
| 8 | VCC | power_in | Power input to be connected to a 5-V supply; recommended supply range is 4.75 V to 5.25 V with absolute maximum of 7 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | DIP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply Voltage | VCC | 7 | V | 4 | |||
| Voltage range at any bus terminal | -10 | 15 | V | 4 | |||
| Enable input voltage | VI | 5.5 | V | 4 | |||
| Operating free-air temperature range | TA | -40 | 85 | °C | 4 | ||
| Storage temperature range | Tstg | 65 | 150 | °C | 4 | ||
| VCC Supply Voltage | VCC | 4.75 | 5 | 5.25 | V | 4 | |
| Voltage at any bus terminal (separately or common mode) | VI or VIC | -7 | 12 | V | separately or common mode | 4 | |
| High-level input voltage | VIH | 2 | V | D, DE, and RE | 4 | ||
| Low-level input voltage | VIL | 0.8 | V | D, DE, and RE | 4 | ||
| Differential input voltage | VID | -12 | 12 | V | Differential bus voltage measured at A with respect to B | 4 | |
| High-level output current | IOH | -60 | mA | Driver | 4 | ||
| High-level output current | IOH | -400 | µA | Receiver | 4 | ||
| Low-level output current | IOL | 60 | mA | Driver | 4 | ||
| Low-level output current | IOL | 8 | mA | Receiver | 4 | ||
| Operating free-air temperature | TA | 0 | 70 | °C | 4 | ||
| High-level output voltage | VOH | 3.7 | V | VIH = 2 V, VIL = 0.8 V, IOH = -33 mA | 5 | ||
| Low-level output voltage | VOL | 1.1 | V | VIH = 2 V, VIL = 0.8 V, IOH = 33 mA | 5 | ||
| Input clamp voltage | VIK | -1.5 | V | II = -18 mA | 5 | ||
| Differential output voltage | /VOD2/ | 2 | 2.7 | V | RL = 100 Ω, see Figure 8 | 5 | |
| Differential output voltage | /VOD2/ | 1.5 | 2.4 | V | RL = 54 Ω, see Figure 8 | 5 | |
| Change in magnitude of differential output voltage | Δ/VOD/ | -0.2 | 0.2 | V | Input changed from high level to low level | 5 | |
| Common-mode output voltage | VOC | 3 | V | RL = 54 Ω or 100 Ω, see Figure 8 | 5 | ||
| Change in magnitude of common-mode output voltage | Δ/VOC/ | -0.2 | 0.2 | V | Input changed from high level to low level | 5 | |
| Output current, output disabled | IO | 1 | mA | Output disabled, VO = 12 V | 5 | ||
| Output current, output disabled | IO | -0.8 | mA | Output disabled, VO = -7 V | 5 | ||
| High-level input current | IIH | 20 | µA | VI = 2.4 V | 5 | ||
| Low-level input current | IIL | -400 | µA | VI = 0.4 V | 5 | ||
| Short-circuit output current | IOS | -250 | mA | VO = -7 V | 5 | ||
| Short-circuit output current | IOS | 250 | mA | VO = VCC | 5 | ||
| Short-circuit output current | IOS | 500 | mA | VO = 12 V | 5 | ||
| Supply current (total package) | ICC | 35 | 50 | mA | No load, outputs enabled | 5 | |
| Supply current (total package) | ICC | 26 | 40 | mA | No load, outputs disabled | 5 | |
| Positive-going input threshold voltage | VIT+ | 0.2 | V | VO = 2.7 V, IO = -0.4 mA | 5 | ||
| Negative-going input threshold voltage | VIT- | -0.2 | V | VO = 0.5 V, IO = 8 mA | 5 | ||
| Input hysteresis voltage (VIT+, VIT-) | Vhys | 50 | mV | 5 | |||
| Enable clamp voltage | VIK | -1.5 | V | II = -18 mA | 5 | ||
| High-level output voltage | VOH | 2.7 | V | VID = 200 mV, IOH = -400 µA, See Figure 9 | 5 | ||
| Low-level output voltage | VOL | 0.45 | V | VID = 200 mV, IOH = 8 mA, See Figure 9 | 5 | ||
| High-impedance-state output current | IOZ | -20 | 20 | µA | VO = 0.4 V to 2.4 V | 5 | |
| Line input current | II | 1 | mA | Other input = 0 V, VI = 12 V | 5 | ||
| Line input current | II | -0.8 | mA | Other input = 0 V, VI = -7 V | 5 | ||
| High-level enable input current | IIH | 20 | µA | VIH = 2.7 V | 5 | ||
| Low-level enable input current | IIL | -100 | µA | VIL = 0.4 V | 5 | ||
| Input resistance | ri | 12 | kΩ | 5 | |||
| Short-circuit output current | IOS | -15 | -85 | mA | 5 | ||
| Differential-output delay time | td(OD) | 40 | 60 | ns | VCC = 5 V, TA = 25°C; RL = 60 Ω, See Figure 10 | 6 | |
| Differential-output transition time | tt(OD) | 65 | 95 | ns | VCC = 5 V, TA = 25°C; RL = 60 Ω, See Figure 10 | 6 | |
| Output enable time to high level | tPZH | 55 | 90 | ns | VCC = 5 V, TA = 25°C; RL = 110 Ω, See Figure 11 | 6 | |
| Output enable time to low level | tPZL | 30 | 50 | ns | VCC = 5 V, TA = 25°C; RL = 110 Ω, See Figure 12 | 6 | |
| Output disable time from high level | tPHZ | 85 | 130 | ns | VCC = 5 V, TA = 25°C; RL = 110 Ω, See Figure 11 | 6 | |
| Output disable time from low level | tPLZ | 20 | 40 | ns | VCC = 5 V, TA = 25°C; RL = 110 Ω, See Figure 12 | 6 | |
| Propagation delay time, low-to-high-level output | tPLH | 21 | 35 | ns | VCC = 5 V, CL = 15 pF, TA = 25°C; VID = -1.5 V to 1.5 V, See Figure 13 | 6 | |
| Propagation delay time, high-to-low-level output | tPHL | 23 | 35 | ns | VCC = 5 V, CL = 15 pF, TA = 25°C; VID = -1.5 V to 1.5 V, See Figure 13 | 6 | |
| Output enable time to high level | tPZH | 10 | 30 | ns | VCC = 5 V, CL = 15 pF, TA = 25°C; See Figure 14 | 6 | |
| Output enable time to low level | tPZL | 12 | 30 | ns | VCC = 5 V, CL = 15 pF, TA = 25°C; See Figure 14 | 6 | |
| Output disable time from high level | tPHZ | 20 | 35 | ns | VCC = 5 V, CL = 15 pF, TA = 25°C; See Figure 14 | 6 | |
| Output disable time from low level | tPLZ | 17 | 25 | ns | VCC = 5 V, CL = 15 pF, TA = 25°C; See Figure 14 | 6 | |
| Junction-to-ambient thermal resistance (P package, DIP-8) | RθJA | 113 | °C/W | P package (8 pins) | 4 |
CAD (KiCad official)
- Symbol:
XL75176AP - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: DIP-8 (KiCad packages3D, STEP)
- 3D model files:
xl75176ap-etched.step/xl75176ap-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xl75176ap.step/xl75176ap.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (16 pp, sha256
db47aae6c7daf71b, retrieved 2026-10-16, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).