component
XD7660
Public Made by Adomby adom
XINLUDA Charge Pumps, DIP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | 25d ago |
| viewers | 25d ago |
| package.json | 25d ago |
| page.json | 25d ago |
| README.md | 25d ago |
| xd7660-etched.glb | 25d ago |
| xd7660-etched.step | 25d ago |
| xd7660-hero.glb | 25d ago |
| xd7660-hero.overlay.json | 25d ago |
| xd7660.glb | 25d ago |
| xd7660.kicad_mod | 25d ago |
| xd7660.kicad_sym | 25d ago |
| xd7660.lbr | 25d ago |
| xd7660.step | 25d ago |
XD7660
XINLUDA · Charge Pumps · DIP-8
XD7660 from XINLUDA, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOST | input | Connecting this pin to V+ raises the oscillator frequency by about 3.5 times, which lowers output impedance and ripple; leaving it open gives the nominal oscillator frequency. |
| 2 | CAP+ | passive | The positive terminal of pump capacitor C1 must be connected to this pin, which is the common charge pump driver node. |
| 3 | GND | power_in | Ground reference; the output (pin 5) must not go more positive than GND, or the device will latch up. |
| 4 | CAP- | passive | Negative side of the pump; the output (pin 5) must not go more positive than this pin, otherwise an external Schottky diode from VOUT to CAP- is needed to prevent latch-up. |
| 5 | VOUT | power_out | Negative converter output, VOUT = -n*VIN; with V+ at or below 5.5V a short to V+ is continuous-rated, while above 5.5V it may only be shorted transiently. |
| 6 | LV | input | Tie to GND for supplies below 3.5V to bypass the internal regulator; leave floating for supplies from 3.5V to 10V to prevent latch-up, and do not connect to GND above 3.5V. |
| 7 | OSC | input | Oscillator terminal: an external capacitor lowers the nominal 10kHz frequency, or an external clock may overdrive it through a 1kΩ series resistor. |
| 8 | V+ | power_in | Positive supply input with a 2V to 10V operating range and a 10.5V absolute maximum; a 2.2µF capacitor to ground may be required for sources with high impedance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | DIP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply current (V+=5V, no load, Pin 1 open) | I+ | 40 | 80 | µA | RL =∞( No load, Pin1 Open), +25°C | 3 | |
| Supply current over temperature (V+=5V) | I+ | 180 | µA | RL =∞( No load, Open), -40°C < TA < +85°C | 3 | ||
| Supply voltage range - high | V+H | 3 | 10 | V | RL = 10k, LV Open, TMIN < TA < TMAX | 3 | |
| Supply voltage range - low | V+L | 2 | 3.5 | V | RL = 10k, LV to GND, TMIN < TA < TMAX | 3 | |
| Output source resistance | ROUT | 55 | 100 | Ω | IOUT = 20mA | 3 | |
| Output source resistance over temperature | ROUT | 150 | Ω | IOUT = 20mA, -40°C < TA < +85°C | 3 | ||
| Output source resistance at low supply | ROUT | 300 | Ω | IOUT = 3mA, V+ = 2V, LV = GND, -40°C < TA < +85°C | 3 | ||
| Power efficiency | PEFF | 96 | 98 | % | RL = 5kΩ | 3 | |
| Power efficiency over temperature | PEFF | 95 | 97 | % | TMIN < TA < TMAX, RL = 5kΩ | 3 | |
| Voltage conversion efficiency | VOUTEFF | 97 | 99 | % | RL =∞( No load, Open), +25°C | 3 | |
| Supply current (V+=3V, no load, Pin 1 open) | I+ | 16 | 50 | µA | V+ = 3V, LV = GND; RL = ∞(No load, Pin 1 Open) | 4 | |
| Supply current over temperature (V+=3V) | I+ | 125 | µA | V+ = 3V, LV = GND; -40°C < TA < +85°C | 4 | ||
| Output source resistance (V+=3V) | ROUT | 97 | 150 | Ω | V+ = 3V, IOUT = 10mA | 4 | |
| Output source resistance over temperature (V+=3V) | ROUT | 200 | Ω | V+ = 3V, -40°C < TA < +85°C | 4 | ||
| Supply voltage (LV input) absolute range | Lv | -0.3 | V | V+ < 5.5V; maximum printed as V+ + 0.3 (not a numeric limit) | 3 | ||
| Supply voltage (V+ pin) | VCC | 10.5 | V | Supply voltage range (V+ pin) | 3 | ||
| Current into Lv | ILV | 25 | μA | V+ > 3.5V | 3 | ||
| Storage temperature range | T | -65 | 150 | ℃ | Storage temperature range | 3 | |
| Thermal resistance junction-to-ambient (DIP-8) | θJA | 115 | °C/W | XD7660 (DIP-8); Note 2: component mounted on evaluation PC board in free air | 3 | ||
| Operating ambient temperature range | Tamb | -40 | 85 | ℃ | Operating | 3 |
CAD (KiCad official)
- Symbol:
XD7660 - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: DIP-8 (KiCad packages3D, STEP)
- 3D model files:
xd7660-etched.step/xd7660-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xd7660.step/xd7660.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (17 pp, sha256
8bc16e7a37ab8cfc, retrieved 2026-10-16, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).