Generated by kicad-footprint-generator · KiCad file format 20260206
X9251UV24IZ-2.7
RENESAS · Digital Potentiometers · TSSOP-24
X9251UV24IZ-2.7 from RENESAS, in a TSSOP-24. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SO | tri_state | Serial data output for the SPI bus; data is shifted out on the falling edge of SCK during a read, and SO is high impedance when CS is HIGH. |
| 2 | A0 | input | Device address input that sets the least significant bit of the SPI slave address and must be tied to a logic level (tWPASU and tWPAH are 0 ns). |
| 3 | RW3 | passive | Wiper terminal of DCP3, equivalent to the wiper terminal of a mechanical potentiometer. |
| 4 | RH3 | passive | High terminal of DCP3, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 5 | RL3 | passive | Low terminal of DCP3, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 6 | NC | unconnected | No connect; must be left floating because the pin is used for Renesas manufacturing and testing. |
| 7 | VCC | power_in | System supply voltage, 2.7 V to 5.5 V for the -2.7 variant, and VCC must always be at least as positive as VH, VL and VW. |
| 8 | RL0 | passive | Low terminal of DCP0, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 9 | RH0 | passive | High terminal of DCP0, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 10 | RW0 | passive | Wiper terminal of DCP0, equivalent to the wiper terminal of a mechanical potentiometer. |
| 11 | CS | input | Active-low SPI chip select; when HIGH the device is deselected and in standby, and a HIGH-to-LOW transition is required after power-up before any operation. |
| 12 | WP | input | Active-low hardware write protect; when LOW it prevents nonvolatile writes to the Data Registers. |
| 13 | SI | input | Serial data input for the SPI bus; opcodes, byte addresses and data are latched on the rising edge of SCK. |
| 14 | A1 | input | Device address input that sets the second least significant bit of the SPI slave address and must be tied to a logic level (tWPASU and tWPAH are 0 ns). |
| 15 | RL1 | passive | Low terminal of DCP1, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 16 | RH1 | passive | High terminal of DCP1, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 17 | RW1 | passive | Wiper terminal of DCP1, equivalent to the wiper terminal of a mechanical potentiometer. |
| 18 | VSS | power_in | System ground for the device. |
| 19 | NC | unconnected | No connect; must be left floating because the pin is used for Renesas manufacturing and testing. |
| 20 | RW2 | passive | Wiper terminal of DCP2, equivalent to the wiper terminal of a mechanical potentiometer. |
| 21 | RH2 | passive | High terminal of DCP2, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 22 | RL2 | passive | Low terminal of DCP2, equivalent to a fixed terminal of a mechanical potentiometer, with voltage limited to VSS to VCC. |
| 23 | SCK | input | Serial clock input for the SPI bus that clocks data into and out of the device. |
| 24 | HOLD | input | Pauses the SPI serial communication when driven LOW while SCK is LOW, and must be held HIGH when the pause feature is not used. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TSSOP-24 |
| Category | Data Converters |
| Pins | 24 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| End to End Resistance (U version) | RTOTAL | 50 | kΩ | U version | 12 | ||
| End to End Resistance Tolerance | -20 | 20 | % | 12 | |||
| Temperature Coefficient of RTOTAL | RTOTAL | -300 | 300 | ppm/°C | Note 14 | 12 | |
| Ratiometric Temperature Coefficient | -20 | 20 | ppm/°C | Note 14 | 12 | ||
| Wiper Resistance | RW | 300 | Ω | IW = at VCC = 3V | 12 | ||
| Wiper Resistance | RW | 220 | Ω | IW = at VCC = 5V | 12 | ||
| Absolute Linearity | -1 | 1 | MI | Rw(n)(actual) - Rw(n)(expected) (Note 13) | 12 | ||
| Relative Linearity | -0.6 | 0.6 | MI | Rw(n + 1) - [Rw(n) + MI] (Note 13) | 12 | ||
| Power Rating (each pot) | 50 | mW | 12 | ||||
| Wiper Current | -3 | 3 | mA | 12 | |||
| Wiper Current (10s) | IW | -6 | 6 | mA | 10s | 12 | |
| Voltage on SCK, CS, SI, SO, WP, HOLD, VCC | -1 | 7 | V | with respect to VSS | 12 | ||
| ΔV = /(VH - VL)/ | 5.5 | V | 12 | ||||
| Lead Temperature | 300 | °C | Soldering, 10s | 12 | |||
| Temperature Under Bias | -65 | 135 | °C | 12 | |||
| Storage Temperature | -65 | 150 | °C | 12 | |||
| Supply Voltage (VCC) Limits | VCC | 2.7 | 5.5 | V | X9251-2.7 supply voltage limits | 12 | |
| Industrial Temperature Range | -40 | 85 | °C | 12 | |||
| VCC Supply Current (Active) | ICC1 | 400 | µA | fSCK = 2.5MHz, SO = Open, VCC = 6V; Other Inputs = VSS | 12 | ||
| VCC Supply Current (Nonvolatile Write) | ICC2 | 1 | 5 | mA | fSCK = 2.5MHz, SO = Open, VCC = 6V; Other Inputs = VSS | 12 | |
| VCC Current (Standby) | ISB | 3 | µA | SCK = SI = VSS, Addr. = VSS, CS = VCC = 6V | 12 | ||
| Input Leakage Current | ILI | 10 | µA | VIN = VSS to VCC | 12 | ||
| Output Leakage Current | ILO | 10 | µA | VOUT = VSS to VCC | 12 | ||
| Output LOW Voltage | VOL | 0.4 | V | IOL = 3mA | 12 | ||
| Minimum Endurance | 100000 | Data changes per bit per register | 13 | ||||
| Data Retention | 100 | years | 13 | ||||
| VCC Power-up Rate | tr | 0.2 | V/ms | VCC (Note 14) | 13 | ||
| Power-up to Initiation of Read Operation | tPUR | 1 | ms | Note 15 | 13 | ||
| Power-up to Initiation of Write Operation | tPUW | 50 | ms | Note 15 | 13 | ||
| SPI clock frequency | fSCK | 2 | MHz | 14 | |||
| SPI Clock Cycle Time | tCYC | 500 | ns | 14 | |||
| SPI Clock High Time | tWH | 200 | ns | 14 | |||
| SPI Clock Low Time | tWL | 200 | ns | 14 | |||
| Lead Time | tLEAD | 250 | ns | 14 | |||
| Lag Time | tLAG | 250 | ns | 14 | |||
| SI, SCK, HOLD and CS Input Setup Time | tSU | 50 | ns | 14 | |||
| SI, SCK, HOLD and CS Input Hold Time | tH | 50 | ns | 14 | |||
| SI, SCK, HOLD and CS Input Rise Time | tRI | 2 | µs | 14 | |||
| SI, SCK, HOLD and CS Input Fall Time | tFI | 2 | µs | 14 | |||
| SO Output Disable Time | tDIS | 0 | 250 | ns | 14 | ||
| SO Output Valid Time | tV | 200 | ns | 14 | |||
| SO Output Hold Time | tHO | 0 | ns | 14 | |||
| SO Output Rise Time | tRO | 100 | ns | Note 14 | 14 | ||
| SO Output Fall Time | tFO | 100 | ns | Note 14 | 14 | ||
| HOLD Time | tHOLD | 400 | ns | 14 | |||
| HOLD Setup Time | tHSU | 100 | ns | 14 | |||
| HOLD Hold Time | tHH | 100 | ns | 14 | |||
| HOLD Low to Output in High Z | tHZ | 100 | ns | 14 | |||
| HOLD High to Output in Low Z | tLZ | 100 | ns | 14 | |||
| CS Deselect Time | tCS | 2 | µs | 14 | |||
| WP, A0 Setup Time | tWPASU | 0 | ns | 14 | |||
| WP, A0 Hold Time | tWPAH | 0 | ns | 14 | |||
| High-voltage write cycle time (store instructions) | tWR | 5 | 10 | ms | 14 | ||
| Wiper response time after the third (last) power supply is stable | tWRPO | 5 | 10 | µs | Note 14 | 14 | |
| Wiper response time after instruction issued (all load instructions) | tWRL | 5 | 10 | µs | Note 14 | 14 |
CAD (KiCad official)
- Symbol:
X9251UV24IZ-2.7 - Footprint:
Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm - 3D model: TSSOP-24 (KiCad packages3D, STEP)
- 3D model files:
x9251uv24iz-2-7-etched.step/x9251uv24iz-2-7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);x9251uv24iz-2-7.step/x9251uv24iz-2-7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (21 pp, sha256
5b6172127b453766, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).