Generated by kicad-footprint-generator · KiCad file format 20260206
W25Q256JVEIQ
Winbond · NOR FLASH · WSON-8-EP(6x8)
W25Q256JVEIQ from Winbond, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | /CS | input | Chip Select input that enables and disables device operation; the device is deselected with /CS high, and it accepts instructions only after /CS transitions from high to low following power-up. |
| 2 | DO (IO1) | bidirectional | Data Output (IO1) used for standard and dual SPI, driven on the falling edge of CLK and at high impedance when the device is deselected. |
| 3 | /WP (IO2) | bidirectional | Write Protect input, active low, used with the Status Register protect bits to prevent Status Register writes, and it becomes IO2 for Quad SPI when QE=1. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | DI (IO0) | bidirectional | Data Input (IO0) used for standard and dual SPI, which latches instructions, addresses and data on the rising edge of CLK. |
| 6 | CLK | input | Serial Clock input that provides the timing for serial input and output operations, with clock frequencies up to 133MHz supported. |
| 7 | /HOLD or /RESET (IO3) | bidirectional | Hold input (active low) that pauses the device while selected, or Reset input, and it becomes IO3 for Quad SPI when QE=1, which disables the HOLD function. |
| 8 | VCC | power_in | Power supply input, specified for a single 2.7V to 3.6V supply. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Winbond |
| Package | WSON-8-EP(6x8) |
| Category | Memory |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | -0.6 | 4.6 | V | 79 | ||
| Voltage Applied to Any Pin | VIO | -0.6 | V | Relative to Ground; max is VCC+0.4 | 79 | ||
| Transient Voltage on any Pin | VIOT | -2 | V | <20nS Transient, Relative to Ground; max is VCC+2.0 | 79 | ||
| Storage Temperature | TSTG | -65 | 150 | °C | 79 | ||
| Electrostatic Discharge Voltage | VESD | -2000 | 2000 | V | Human Body Model | 79 | |
| Supply Voltage | VCC | 3 | 3.6 | V | FR = 133MHz, fR = 50MHz | 79 | |
| Supply Voltage | VCC | 2.7 | 3 | V | FR = 104MHz, fR = 50MHz | 79 | |
| Ambient Temperature, Operating | TA | -40 | 85 | °C | Industrial | 79 | |
| VCC (min) to /CS Low | tVSL | 20 | µs | 80 | |||
| Time Delay Before Write Instruction | tPUW | 5 | ms | 80 | |||
| Write Inhibit Threshold Voltage | VWI | 1 | 2 | V | 80 | ||
| Input Capacitance | CIN | 6 | pF | VIN = 0V | 81 | ||
| Output Capacitance | Cout | 8 | pF | VOUT = 0V | 81 | ||
| Input Leakage | ILI | -2 | 2 | µA | 81 | ||
| I/O Leakage | ILO | -2 | 2 | µA | 81 | ||
| Standby Current | ICC1 | 10 | 60 | µA | /CS = VCC, VIN = GND or VCC | 81 | |
| Power-down Current | ICC2 | 1 | 20 | µA | /CS = VCC, VIN = GND or VCC | 81 | |
| Current Read Data / Dual /Quad 50MHz | ICC3 | 15 | mA | C = 0.1 VCC / 0.9 VCC, DO = Open | 81 | ||
| Current Read Data / Dual Output Read/Quad Output Read 104MHz | ICC3 | 20 | mA | C = 0.1 VCC / 0.9 VCC, DO = Open | 81 | ||
| Current Write Status Register | ICC4 | 20 | 25 | mA | /CS = VCC | 81 | |
| Current Page Program | ICC5 | 20 | 25 | mA | /CS = VCC | 81 | |
| Current Sector/Block Erase | ICC6 | 20 | 25 | mA | /CS = VCC | 81 | |
| Current Chip Erase | ICC7 | 20 | 25 | mA | /CS = VCC | 81 | |
| Input Low Voltage | VIL | -0.5 | V | max is VCC x 0.3 | 81 | ||
| Output Low Voltage | VOL | 0.2 | V | IOL = 100 µA | 81 | ||
| Load Capacitance | CL | 30 | pF | 82 | |||
| Input Rise and Fall Times | TR, TF | 5 | ns | 82 | |||
| Clock frequency except for Read Data (03h) & DTR instructions (3.0V-3.6V) | FR | 133 | MHz | 3.0V-3.6V | 83 | ||
| Clock frequency except for Read Data (03h) & DTR instructions (2.7V-3.0V) | FR | 104 | MHz | 2.7V-3.0V | 83 | ||
| Clock frequency for Read Data instruction (03h) | fR | 50 | MHz | 83 | |||
| /CS Active Setup Time relative to CLK | tSLCH | 5 | ns | 83 | |||
| /CS Not Active Hold Time relative to CLK | tCHSL | 5 | ns | 83 | |||
| Data In Setup Time | tDVCH | 2 | ns | 83 | |||
| Data In Hold Time | tCHDX | 3 | ns | 83 | |||
| /CS Active Hold Time relative to CLK | tCHSH | 3 | ns | 83 | |||
| /CS Not Active Setup Time relative to CLK | tSHCH | 3 | ns | 83 | |||
| /CS Deselect Time (During Read) | tSHSL1 | 10 | ns | 83 | |||
| /CS Deselect Time (During Erase or Program or Write) | tSHSL2 | 50 | ns | 83 | |||
| Output Disable Time | tSHQZ | 7 | ns | 83 | |||
| Clock Low to Output Valid | tCLQV1 | 6 | ns | 83 | |||
| Output Hold Time | tCLQX | 1.5 | ns | 83 | |||
| Write Protect Setup Time Before /CS Low | tWHSL | 20 | ns | 84 | |||
| Write Protect Hold Time After /CS High | tSHWL | 100 | ns | 84 | |||
| /CS High to Power-down Mode | tDP | 3 | µs | 84 | |||
| /CS High to Standby Mode without ID Read | tRES1 | 3 | µs | 84 | |||
| /CS High to Standby Mode with ID Read | tRES2 | 1.8 | µs | 84 | |||
| /CS High to next Instruction after Suspend | tSUS | 20 | µs | 84 | |||
| /CS High to next Instruction after Reset | tRST | 30 | µs | 84 | |||
| /RESET pin Low period to reset the device | tRESET | 1 | µs | Recommended minimum (see note 4) | 84 | ||
| Write Status Register Time | tW | 10 | 15 | ms | 84 | ||
| Page Program Time | tPP | 0.7 | 3 | ms | 84 | ||
| Sector Erase Time (4KB) | tSE | 50 | 400 | ms | 84 | ||
| Block Erase Time (32KB) | tBE1 | 120 | 1600 | ms | 84 | ||
| Block Erase Time (64KB) | tBE2 | 150 | 2000 | ms | 84 | ||
| Chip Erase Time | tCE | 80 | 400 | s | 84 |
CAD (KiCad official)
- Symbol:
W25Q256JVEIQ - Footprint:
Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm - 3D model: WSON-8-EP(6x8), generated on the KiCad land (body 8 x 6 mm, terminals on the pads, 0.75 mm tall, family nominal (no datasheet A read)). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
w25q256jveiq-etched.step/w25q256jveiq-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);w25q256jveiq.step/w25q256jveiq.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Winbond datasheet (92 pp, sha256
0f18a76476aee735, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).