main
Ray
Publish 0.1.0
112fcb9
VIPER28HN
STMicroelectronics · AC-DC Controllers & Regulators · DIP-7
VIPER28HN from STMicroelectronics, in a DIP-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Device ground and the source of the power section. |
| 2 | VDD | power_in | Supply voltage of the control section (operating range 8.5 V to 23.5 V after turn-on), which also provides the charging current of the external capacitor during startup. |
| 3 | CONT | input | Control pin that reduces the current limit setpoint (IDlim) via an external resistor to ground and monitors output voltage for overvoltage protection (VOVP threshold 3 V typ). |
| 4 | FB | input | Control input for duty cycle control with internal bias current source; a voltage below VFBbm (0.6 V typ) activates burst mode and a level near VFBlin (3.5 V typ) indicates approaching the cycle-by-cycle overcurrent setpoint. |
| 5 | EPT | passive | Connection for an external capacitor setting the extra power timer; must be connected to GND if the function is not used. |
| 7 | DRAIN | passive | High-voltage drain pin (800 V max) that also supplies the switched startup bias current and is connected to the metal frame for heat dissipation. |
| 8 | DRAIN | passive | High-voltage drain pin (800 V max) that also supplies the switched startup bias current and is connected to the metal frame for heat dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | DIP-7 |
| Category | Power Supply Chip |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Drain-to-source (ground) voltage | VDRAIN | 800 | V | 7 | |||
| Pulse drain current | IDRAIN | 3 | A | limited by TJ = 150 °C | 7 | ||
| Control input pin voltage | VCONT | -0.3 | 6 | V | 7 | ||
| Feedback voltage | VFB | -0.3 | 5.5 | V | 7 | ||
| EPT input pin voltage | VEPT | -0.3 | 5 | V | 7 | ||
| Supply voltage (self limited) | VDD | -0.3 | V | IDD = 25 mA | 7 | ||
| Input current | IDD | 25 | mA | 7 | |||
| Power dissipation (DIP-7) | PTOT | 1 | W | TA < 40 °C (DIP-7) | 7 | ||
| Operating junction temperature range | TJ | -40 | 150 | °C | 7 | ||
| Storage temperature | TSTG | -55 | 150 | °C | 7 | ||
| Human body model ESD | HBM(ESD) | 2 | kV | Human body model | 7 | ||
| Charge device mode ESD | ESD(CDM) | 1.5 | kV | Charge device mode | 7 | ||
| Thermal resistance junction pin (DIP7) | RthJP | 35 | °C/W | dissipated power = 1 W | 7 | ||
| Thermal resistance junction ambient (DIP7) | RthJA | 110 | °C/W | dissipated power = 1 W | 7 | ||
| Avalanche current | IAS | 1 | A | Repetitive or non repetitive (pulse width limited by TJmax) | 7 | ||
| Single pulse avalanche energy | EAS | 3 | mJ | ID = IAS, VDS=100 V, starting TJ = 25°C | 7 | ||
| Breakdown voltage | VBVDSS | 800 | V | IDRAIN = 1 mA, VFB = GND, TJ = 25 °C | 8 | ||
| OFF-state drain current | IOFF | 60 | µA | VDRAIN = max rating,VFB = GND, TJ = 25°C | 8 | ||
| Drain-source on-state resistance | RDS(on) | 7 | Ω | IDRAIN = 0.4 A, VFB = 3 V, VEPT = GND, TJ = 25 °C | 8 | ||
| Drain-source on-state resistance | RDS(on) | 14 | Ω | IDRAIN = 0.4 A, VFB = 3 V, VEPT = GND, TJ = 125 °C | 8 | ||
| Drain-source start voltage | VDRAIN_START | 60 | 80 | 100 | V | 8 | |
| Startup charging current | IDDch1 | -2 | -3 | -4 | mA | VDRAIN = 120 V, VEPT = GND, VFB = GND, VDD = 4 V | 8 |
| Restart charging current (after fault) | IDDch2 | -0.4 | -0.6 | -0.8 | mA | VDRAIN = 120 V, VEPT = GND, VFB = GND, VDD = 5 V | 8 |
| VDD operating voltage range | VDD | 8.5 | 23.5 | V | After turn-on | 8 | |
| VDD clamp voltage | VDDclamp | 23.5 | V | IDD = 20 mA | 8 | ||
| VDD startup threshold | VDDon | 13 | 14 | 15 | V | VDRAIN = 120 V, VEPT = GND, VFB = GND | 8 |
| VDD undervoltage shutdown threshold | VDDoff | 7.5 | 8 | 8.5 | V | 8 | |
| VDD restart voltage threshold | VDD(RESTART) | 4 | 4.5 | 5 | V | VDRAIN = 120 V, VEPT = GND, VFB = GND | 8 |
| Operating supply current, not switching | IDD0 | 0.9 | mA | VFB = GND, FOSC = 0 kHz, VEPT = GND, VDD = 10 V | 8 | ||
| Operating supply current, switching (115 kHz) | IDD1 | 3.5 | mA | VDRAIN = 120 V,FOSC = 115 kHz | 8 | ||
| Operating supply current, with protection tripping | IDD_FAULT | 400 | uA | VDD = 10 V | 8 | ||
| Operating supply current with VDD < VDD_OFF | IDD_OFF | 270 | uA | VDD = 7 V | 8 | ||
| Overload shutdown threshold | VFBolp | 4.5 | 4.8 | 5.2 | V | 9 | |
| Overload detection threshold | VFBlin | 3.2 | 3.5 | 3.7 | V | 9 | |
| Burst mode threshold | VFBbm | 0.54 | 0.6 | 0.66 | V | Voltage falling | 9 |
| Feedback sourced current | IFB1 | -150 | -200 | -280 | uA | VFB = 0.3 V | 9 |
| Low-level clamp voltage (CONT) | VCONT_l | 0.4 | 0.5 | 0.6 | V | ICONT = -100 µA | 9 |
| High-level clamp voltage (CONT) | VCONT_h | 5 | 5.5 | 6 | V | ICONT = 1 mA | 9 |
| Max drain current limitation | IDlim | 0.75 | 0.8 | 0.85 | A | VFB = 4 V, ICONT = -10 µA, TJ = 25 °C | 9 |
| Soft-start time | tSS | 7.6 | 8.5 | 9.4 | ms | 9 | |
| Minimum turn-on time | TON_MIN | 220 | 370 | 480 | ns | 9 | |
| Oscillator frequency (H type) | FOSC | 103 | 115 | 127 | kHz | VFB = 1 V | 9 |
| Modulation depth (H type) | FD | -8 | 8 | kHz | VIPER28H | 9 | |
| Modulation frequency | FM | 200 | 250 | 300 | Hz | 9 | |
| Maximum duty cycle | DMAX | 70 | 80 | % | 9 | ||
| Second overcurrent threshold | IDMAX | 1.2 | A | 9 | |||
| Overvoltage protection threshold | VOVP | 2.7 | 3 | 3.3 | V | 9 | |
| EPT shutdown threshold | VEPT(STOP) | 3.6 | 4 | 4.4 | V | ICONT < -10 µA | 10 |
| EPT restart threshold | VEPT(RESTART) | 0.4 | 0.6 | 0.8 | V | 10 | |
| EPT sink/source current | IEPT | 4 | 5 | 6 | µA | 10 | |
| Thermal shutdown temperature | TSD | 150 | 160 | °C | 10 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | Note: The copper area for heat dissipation has to be designed under the DRAIN pins. | 6 |
CAD (KiCad official)
- Symbol:
VIPER28HN - Footprint:
Package_DIP:DIP-8-N6_W7.62mm - 3D model: DIP-7 (KiCad packages3D, STEP)
- 3D model files:
viper28hn-etched.step/viper28hn-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);viper28hn.step/viper28hn.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (31 pp, sha256
77f7390609cc2adb, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# VIPER28HN
**STMicroelectronics** · AC-DC Controllers & Regulators · DIP-7
VIPER28HN from STMicroelectronics, in a DIP-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Device ground and the source of the power section. |
| 2 | VDD | power_in | Supply voltage of the control section (operating range 8.5 V to 23.5 V after turn-on), which also provides the charging current of the external capacitor during startup. |
| 3 | CONT | input | Control pin that reduces the current limit setpoint (IDlim) via an external resistor to ground and monitors output voltage for overvoltage protection (VOVP threshold 3 V typ). |
| 4 | FB | input | Control input for duty cycle control with internal bias current source; a voltage below VFBbm (0.6 V typ) activates burst mode and a level near VFBlin (3.5 V typ) indicates approaching the cycle-by-cycle overcurrent setpoint. |
| 5 | EPT | passive | Connection for an external capacitor setting the extra power timer; must be connected to GND if the function is not used. |
| 7 | DRAIN | passive | High-voltage drain pin (800 V max) that also supplies the switched startup bias current and is connected to the metal frame for heat dissipation. |
| 8 | DRAIN | passive | High-voltage drain pin (800 V max) that also supplies the switched startup bias current and is connected to the metal frame for heat dissipation. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | DIP-7 |
| Category | Power Supply Chip |
| Pins | 7 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Drain-to-source (ground) voltage | VDRAIN | | | 800 | V | | 7 |
| Pulse drain current | IDRAIN | | | 3 | A | limited by TJ = 150 °C | 7 |
| Control input pin voltage | VCONT | -0.3 | | 6 | V | | 7 |
| Feedback voltage | VFB | -0.3 | | 5.5 | V | | 7 |
| EPT input pin voltage | VEPT | -0.3 | | 5 | V | | 7 |
| Supply voltage (self limited) | VDD | -0.3 | | | V | IDD = 25 mA | 7 |
| Input current | IDD | | | 25 | mA | | 7 |
| Power dissipation (DIP-7) | PTOT | | | 1 | W | TA < 40 °C (DIP-7) | 7 |
| Operating junction temperature range | TJ | -40 | | 150 | °C | | 7 |
| Storage temperature | TSTG | -55 | | 150 | °C | | 7 |
| Human body model ESD | HBM(ESD) | | | 2 | kV | Human body model | 7 |
| Charge device mode ESD | ESD(CDM) | | | 1.5 | kV | Charge device mode | 7 |
| Thermal resistance junction pin (DIP7) | RthJP | | | 35 | °C/W | dissipated power = 1 W | 7 |
| Thermal resistance junction ambient (DIP7) | RthJA | | | 110 | °C/W | dissipated power = 1 W | 7 |
| Avalanche current | IAS | | | 1 | A | Repetitive or non repetitive (pulse width limited by TJmax) | 7 |
| Single pulse avalanche energy | EAS | | | 3 | mJ | ID = IAS, VDS=100 V, starting TJ = 25°C | 7 |
| Breakdown voltage | VBVDSS | 800 | | | V | IDRAIN = 1 mA, VFB = GND, TJ = 25 °C | 8 |
| OFF-state drain current | IOFF | | | 60 | µA | VDRAIN = max rating,VFB = GND, TJ = 25°C | 8 |
| Drain-source on-state resistance | RDS(on) | | | 7 | Ω | IDRAIN = 0.4 A, VFB = 3 V, VEPT = GND, TJ = 25 °C | 8 |
| Drain-source on-state resistance | RDS(on) | | | 14 | Ω | IDRAIN = 0.4 A, VFB = 3 V, VEPT = GND, TJ = 125 °C | 8 |
| Drain-source start voltage | VDRAIN_START | 60 | 80 | 100 | V | | 8 |
| Startup charging current | IDDch1 | -2 | -3 | -4 | mA | VDRAIN = 120 V, VEPT = GND, VFB = GND, VDD = 4 V | 8 |
| Restart charging current (after fault) | IDDch2 | -0.4 | -0.6 | -0.8 | mA | VDRAIN = 120 V, VEPT = GND, VFB = GND, VDD = 5 V | 8 |
| VDD operating voltage range | VDD | 8.5 | | 23.5 | V | After turn-on | 8 |
| VDD clamp voltage | VDDclamp | | | 23.5 | V | IDD = 20 mA | 8 |
| VDD startup threshold | VDDon | 13 | 14 | 15 | V | VDRAIN = 120 V, VEPT = GND, VFB = GND | 8 |
| VDD undervoltage shutdown threshold | VDDoff | 7.5 | 8 | 8.5 | V | | 8 |
| VDD restart voltage threshold | VDD(RESTART) | 4 | 4.5 | 5 | V | VDRAIN = 120 V, VEPT = GND, VFB = GND | 8 |
| Operating supply current, not switching | IDD0 | | | 0.9 | mA | VFB = GND, FOSC = 0 kHz, VEPT = GND, VDD = 10 V | 8 |
| Operating supply current, switching (115 kHz) | IDD1 | | | 3.5 | mA | VDRAIN = 120 V,FOSC = 115 kHz | 8 |
| Operating supply current, with protection tripping | IDD_FAULT | | | 400 | uA | VDD = 10 V | 8 |
| Operating supply current with VDD < VDD_OFF | IDD_OFF | | | 270 | uA | VDD = 7 V | 8 |
| Overload shutdown threshold | VFBolp | 4.5 | 4.8 | 5.2 | V | | 9 |
| Overload detection threshold | VFBlin | 3.2 | 3.5 | 3.7 | V | | 9 |
| Burst mode threshold | VFBbm | 0.54 | 0.6 | 0.66 | V | Voltage falling | 9 |
| Feedback sourced current | IFB1 | -150 | -200 | -280 | uA | VFB = 0.3 V | 9 |
| Low-level clamp voltage (CONT) | VCONT_l | 0.4 | 0.5 | 0.6 | V | ICONT = -100 µA | 9 |
| High-level clamp voltage (CONT) | VCONT_h | 5 | 5.5 | 6 | V | ICONT = 1 mA | 9 |
| Max drain current limitation | IDlim | 0.75 | 0.8 | 0.85 | A | VFB = 4 V, ICONT = -10 µA, TJ = 25 °C | 9 |
| Soft-start time | tSS | 7.6 | 8.5 | 9.4 | ms | | 9 |
| Minimum turn-on time | TON_MIN | 220 | 370 | 480 | ns | | 9 |
| Oscillator frequency (H type) | FOSC | 103 | 115 | 127 | kHz | VFB = 1 V | 9 |
| Modulation depth (H type) | FD | -8 | | 8 | kHz | VIPER28H | 9 |
| Modulation frequency | FM | 200 | 250 | 300 | Hz | | 9 |
| Maximum duty cycle | DMAX | 70 | | 80 | % | | 9 |
| Second overcurrent threshold | IDMAX | | | 1.2 | A | | 9 |
| Overvoltage protection threshold | VOVP | 2.7 | 3 | 3.3 | V | | 9 |
| EPT shutdown threshold | VEPT(STOP) | 3.6 | 4 | 4.4 | V | ICONT < -10 µA | 10 |
| EPT restart threshold | VEPT(RESTART) | 0.4 | 0.6 | 0.8 | V | | 10 |
| EPT sink/source current | IEPT | 4 | 5 | 6 | µA | | 10 |
| Thermal shutdown temperature | TSD | 150 | | 160 | °C | | 10 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | Note: The copper area for heat dissipation has to be designed under the DRAIN pins. | 6 |
## CAD (KiCad official)
- Symbol: `VIPER28HN`
- Footprint: `Package_DIP:DIP-8-N6_W7.62mm`
- 3D model: DIP-7 (KiCad packages3D, STEP)
- 3D model files: `viper28hn-etched.step` / `viper28hn-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `viper28hn.step` / `viper28hn.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/viper28hn.pdf) (31 pp, sha256 `77f7390609cc2adb`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/viper28hn-datasheet.pdf)