main
Ray Publish 0.1.0 106fc1f

USB2514B-AEZG-TR

Microchip Tech · USB ICs · TQFN-36-EP(6x6)

USB2514B-AEZG-TR from Microchip Tech, in a TQFN-36-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 USBDM_DN1 / PRT_DIS_M1 bidirectional Hi-speed USB data minus for downstream port 1, which doubles as the port 1 disable strap sampled at RESET_N negation; a 10 k pull-up to 3.3 V disables the port.
2 USBDP_DN1 / PRT_DIS_P1 bidirectional Hi-speed USB data plus for downstream port 1, which doubles as the port 1 disable strap; a 10 k pull-up to 3.3 V disables the port.
3 USBDM_DN2 / PRT_DIS_M2 bidirectional Hi-speed USB data minus for downstream port 2, which doubles as the port 2 disable strap sampled at RESET_N negation.
4 USBDP_DN2 / PRT_DIS_P2 bidirectional Hi-speed USB data plus for downstream port 2, which doubles as the port 2 disable strap; a 10 k pull-up to 3.3 V disables the port.
5 VDDA33 power_in 3.3 V analog power supply pin.
6 USBDM_DN3 / PRT_DIS_M3 bidirectional Hi-speed USB data minus for downstream port 3, which doubles as the port 3 disable strap sampled at RESET_N negation.
7 USBDP_DN3 / PRT_DIS_P3 bidirectional Hi-speed USB data plus for downstream port 3, which doubles as the port 3 disable strap; a 10 k pull-up to 3.3 V disables the port.
8 USBDM_DN4 / PRT_DIS_M4 bidirectional Hi-speed USB data minus for downstream port 4, which doubles as the port 4 disable strap sampled at RESET_N negation.
9 USBDP_DN4 / PRT_DIS_P4 bidirectional Hi-speed USB data plus for downstream port 4, which doubles as the port 4 disable strap; a 10 k pull-up to 3.3 V disables the port.
10 VDDA33 power_in 3.3 V analog power supply pin.
11 TEST passive Test pin with internal pull-down that must be treated as a no connect or tied to ground, with no trace or signal routed to it.
12 PRTPWR1/BC_EN1 output USB port 1 power enable output that supplies VBUS to the downstream device; BC_EN1 is sampled at RESET_N negation to enable battery charging on port 1 when pulled high.
13 OCS_N1 input Active-low over-current sense input for port 1 from an external current monitor, with an internal pull-up.
14 CRFILT passive Core regulator filter capacitor pin, which can take up to a 0.1 µF low-ESR capacitor to VSS or be left unconnected.
15 VDD33 power_in 3.3 V digital power supply pin.
16 PRTPWR2/BC_EN2 output USB port 2 power enable output that supplies VBUS to the downstream device; BC_EN2 is sampled at RESET_N negation to enable battery charging on port 2 when pulled high.
17 OCS_N2 input Active-low over-current sense input for port 2 from an external current monitor, with an internal pull-up.
18 PRTPWR3/BC_EN3 output USB port 3 power enable output that supplies VBUS to the downstream device; BC_EN3 is sampled at RESET_N negation to enable battery charging on port 3 when pulled high.
19 OCS_N3 input Active-low over-current sense input for port 3 from an external current monitor, with an internal pull-up.
20 PRTPWR4 / BC_EN4 output USB port 4 power enable output that supplies VBUS to the downstream device; BC_EN4 is sampled at RESET_N negation to enable battery charging on port 4 when pulled high.
21 OCS_N4 input Active-low over-current sense input for port 4 from an external current monitor, with an internal pull-up.
22 SDA / SMBDATA / NON_REM1 bidirectional Serial data for the I2C EEPROM or SMBus interface, which doubles as the NON_REM1 strap sampled at RESET_N negation to set non-removable ports.
23 VDD33 power_in 3.3 V digital power supply pin.
24 SCL / SMBCLK / CFG_SEL0 bidirectional Serial clock for the I2C EEPROM or SMBus interface, which doubles as the CFG_SEL0 configuration select latched on the rising edge of RESET_N.
25 CFG_SEL1 / HS_IND bidirectional Configuration select 1 latched on the rising edge of RESET_N, which doubles as the hi-speed upstream port indicator asserted when the hub connects at high speed.
26 RESET_N input Active-low system reset input; the minimum active low pulse is 1 µs.
27 VBUS_DET input Detects the state of upstream VBUS power to control the internal D+ pull-up; for a detachable hub it connects to VBUS through a 2:1 divider using two 100 k resistors.
28 SUSP_IND/LOCAL_PWR/NON_REM0 bidirectional Active/suspend status indicator, which doubles as the local power detect input (low means no local power source) and the NON_REM0 strap sampled at RESET_N negation.
29 VDDA33 power_in 3.3 V analog power supply pin.
30 USBDM_UP bidirectional Upstream USB data minus signal, connected to the upstream host, port, or upstream hub.
31 USBDP_UP bidirectional Upstream USB data plus signal, connected to the upstream host, port, or upstream hub.
32 XTALOUT output 24 MHz crystal output with 1.2 V p-p swing and weak (<1 mA) drive; leave unconnected when an external clock drives XTALIN/CLKIN.
33 XTALIN/CLKIN input 24 MHz crystal input, or external 24 MHz clock input when no crystal is used.
34 PLLFILT passive PLL regulator filter capacitor pin, which can take up to a 0.1 µF low-ESR capacitor to VSS or be left unconnected.
35 RBIAS passive USB transceiver bias pin; a 12.0 kΩ (±1%) resistor is connected from this pin to ground.
36 VDDA33 power_in 3.3 V analog power supply pin.
37 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TQFN-36-EP(6x6)
Category Communication Interface Chip/UART/485/232
Pins 37

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
3.3 V supply voltage VDD33, VDDA33 3 3.6 V Applies to all parts 39
3.3 V supply voltage VDD33, VDDA33 4.6 V Applies to all packages 39
Storage Temperature TSTOR -55 150 °C 39
Voltage on any I/O pin -0.5 5.5 V 39
Voltage on XTALIN -0.5 4 V 39
Voltage on XTALOUT -0.5 2.5 V Note 6-1 39
Extended Commercial Operating Temperature TAE 0 85 °C Ambient temperature in still air 39
Voltage on any I/O pin -0.3 5.5 V If any 3.3 V supply voltage drops below 3.0 V, then the MAX becomes (3.3 V supply voltage) + 0.5 39
Voltage on XTALIN -0.3 V MAX printed as VDD33 39
3.3 V supply rise time tRT33 0 400 µs See Figure 6-1 and Note 6-2 39
Low Input Level (I, IS type) VILI 0.8 V TTL Levels 40
High Input Level (I, IS type) VIHI 2 V 40
Input Leakage (I, IS type) IIL -10 10 µA VIN = 0 to VDD33 40
Hysteresis (IS only) VHYSI 250 350 mV IS only 40
Low Input Level (IPU) VILI 0.8 V TTL Levels 40
High Input Level (IPU) VIHI 2 V 40
Low Input Leakage (IPU) IILL 35 90 µA VIN = 0 40
High Input Leakage (IPU) IIHL -10 10 µA VIN = VDD33 40
Low Input Level (IPD) VILI 0.8 V TTL Levels 40
High Input Level (IPD) VIHI 2 V 40
Low Input Leakage (IPD) IILL 10 -10 µA VIN = 0 40
High Input Leakage (IPD) IIHL -35 -90 µA VIN = VDD33 40
Low Input Level (ICLK) VILCK 0.3 V 40
High Input Level (ICLK) VIHCK 0.9 V 40
Input Leakage (ICLK) IIL -10 10 µA VIN = 0 to VDD33 40
Output Leakage (O12, I/O12, I/OSD12) IOL -10 10 µA Note 6-3, current pins in high impedance 41
Low Output Level (O12, I/O12, I/OSD12) VOL 0.4 V IOL = 12 mA @ VDD33 = 3.3 V 41
High Output Level (O12, I/O12, I/OSD12) VOH 2.4 V IOH = -12 mA @ VDD33 = 3.3 V 41
Hysteresis (SD pad only) IHYSC 250 350 mV VIN = VDD33 (Note 6-1) 41
Supply Current Unconfigured: Hi-Speed Host (USB2514B) ICCINTHS 50 mA Unconfigured, hi-speed host 41
Supply Current Configured: Hi-Speed Host, 1 port base (USB2514B) IHCH1 80 mA Base current of one downstream port; each additional port adds 25 mA 41
Supply Current Configured: Full-Speed Host (USB2514B) IFCC1 60 mA Base current of one downstream port; each additional port adds 8 mA 42
Supply Current Suspend (USB2514B) ICSBY 1200 µA All supplies combined 42
Supply Current Reset (USB2514B) ICRST 1400 µA All supplies combined 42
Clock Input Capacitance CXTAL 6 pF All pins except USB pins and the pins under the test tied to AC ground 42
Input Capacitance CIN 6 pF Note 6-5, TA = 25°C; fc = 1 MHz; VDD33 = 3.3 V 42
Output Capacitance COUT 6 pF Note 6-5, TA = 25°C; fc = 1 MHz; VDD33 = 3.3 V 42
Crystal frequency tolerance -350 24 350 ppm Crystal: parallel resonant, fundamental mode, 24 MHz; typ holds nominal 24 MHz 44
External clock frequency tolerance -350 24 350 ppm External clock, 24 MHz 45
External clock duty cycle tolerance -10 50 10 % External clock duty cycle 50% ±10% 45
RESET_N asserted t1 1 s Minimum assertion of RESET_N after supplies within operating range 36
CFG_SEL[1:0] setup time t2 16.7 ns 36
CFG_SEL[1:0] hold time t3 16.7 1400 ns 36
Hub outputs driven to inactive logic states t4 1.5 2 s 36
Slave device timeout (master detect) TTIMEOUT, MIN 25 ms Any single clock low interval exceeding this aborts transfer 34
Slave device timeout (slave reset) TTIMEOUT, MAX 35 ms Slave must be able to receive new START no later than this 34

CAD (KiCad official)

  • Symbol: USB2514B-AEZG-TR
  • Footprint: Package_DFN_QFN:QFN-36-1EP_6x6mm_P0.5mm_EP3.7x3.7mm
  • 3D model: TQFN-36-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: usb2514b-aezg-tr-etched.step / usb2514b-aezg-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); usb2514b-aezg-tr.step / usb2514b-aezg-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (57 pp, sha256 3fca1a17701a3fd5, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF