Generated by kicad-footprint-generator · KiCad file format 20260206
USB2514B-AEZG-TR
Microchip Tech · USB ICs · TQFN-36-EP(6x6)
USB2514B-AEZG-TR from Microchip Tech, in a TQFN-36-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | USBDM_DN1 / PRT_DIS_M1 | bidirectional | Hi-speed USB data minus for downstream port 1, which doubles as the port 1 disable strap sampled at RESET_N negation; a 10 k pull-up to 3.3 V disables the port. |
| 2 | USBDP_DN1 / PRT_DIS_P1 | bidirectional | Hi-speed USB data plus for downstream port 1, which doubles as the port 1 disable strap; a 10 k pull-up to 3.3 V disables the port. |
| 3 | USBDM_DN2 / PRT_DIS_M2 | bidirectional | Hi-speed USB data minus for downstream port 2, which doubles as the port 2 disable strap sampled at RESET_N negation. |
| 4 | USBDP_DN2 / PRT_DIS_P2 | bidirectional | Hi-speed USB data plus for downstream port 2, which doubles as the port 2 disable strap; a 10 k pull-up to 3.3 V disables the port. |
| 5 | VDDA33 | power_in | 3.3 V analog power supply pin. |
| 6 | USBDM_DN3 / PRT_DIS_M3 | bidirectional | Hi-speed USB data minus for downstream port 3, which doubles as the port 3 disable strap sampled at RESET_N negation. |
| 7 | USBDP_DN3 / PRT_DIS_P3 | bidirectional | Hi-speed USB data plus for downstream port 3, which doubles as the port 3 disable strap; a 10 k pull-up to 3.3 V disables the port. |
| 8 | USBDM_DN4 / PRT_DIS_M4 | bidirectional | Hi-speed USB data minus for downstream port 4, which doubles as the port 4 disable strap sampled at RESET_N negation. |
| 9 | USBDP_DN4 / PRT_DIS_P4 | bidirectional | Hi-speed USB data plus for downstream port 4, which doubles as the port 4 disable strap; a 10 k pull-up to 3.3 V disables the port. |
| 10 | VDDA33 | power_in | 3.3 V analog power supply pin. |
| 11 | TEST | passive | Test pin with internal pull-down that must be treated as a no connect or tied to ground, with no trace or signal routed to it. |
| 12 | PRTPWR1/BC_EN1 | output | USB port 1 power enable output that supplies VBUS to the downstream device; BC_EN1 is sampled at RESET_N negation to enable battery charging on port 1 when pulled high. |
| 13 | OCS_N1 | input | Active-low over-current sense input for port 1 from an external current monitor, with an internal pull-up. |
| 14 | CRFILT | passive | Core regulator filter capacitor pin, which can take up to a 0.1 µF low-ESR capacitor to VSS or be left unconnected. |
| 15 | VDD33 | power_in | 3.3 V digital power supply pin. |
| 16 | PRTPWR2/BC_EN2 | output | USB port 2 power enable output that supplies VBUS to the downstream device; BC_EN2 is sampled at RESET_N negation to enable battery charging on port 2 when pulled high. |
| 17 | OCS_N2 | input | Active-low over-current sense input for port 2 from an external current monitor, with an internal pull-up. |
| 18 | PRTPWR3/BC_EN3 | output | USB port 3 power enable output that supplies VBUS to the downstream device; BC_EN3 is sampled at RESET_N negation to enable battery charging on port 3 when pulled high. |
| 19 | OCS_N3 | input | Active-low over-current sense input for port 3 from an external current monitor, with an internal pull-up. |
| 20 | PRTPWR4 / BC_EN4 | output | USB port 4 power enable output that supplies VBUS to the downstream device; BC_EN4 is sampled at RESET_N negation to enable battery charging on port 4 when pulled high. |
| 21 | OCS_N4 | input | Active-low over-current sense input for port 4 from an external current monitor, with an internal pull-up. |
| 22 | SDA / SMBDATA / NON_REM1 | bidirectional | Serial data for the I2C EEPROM or SMBus interface, which doubles as the NON_REM1 strap sampled at RESET_N negation to set non-removable ports. |
| 23 | VDD33 | power_in | 3.3 V digital power supply pin. |
| 24 | SCL / SMBCLK / CFG_SEL0 | bidirectional | Serial clock for the I2C EEPROM or SMBus interface, which doubles as the CFG_SEL0 configuration select latched on the rising edge of RESET_N. |
| 25 | CFG_SEL1 / HS_IND | bidirectional | Configuration select 1 latched on the rising edge of RESET_N, which doubles as the hi-speed upstream port indicator asserted when the hub connects at high speed. |
| 26 | RESET_N | input | Active-low system reset input; the minimum active low pulse is 1 µs. |
| 27 | VBUS_DET | input | Detects the state of upstream VBUS power to control the internal D+ pull-up; for a detachable hub it connects to VBUS through a 2:1 divider using two 100 k resistors. |
| 28 | SUSP_IND/LOCAL_PWR/NON_REM0 | bidirectional | Active/suspend status indicator, which doubles as the local power detect input (low means no local power source) and the NON_REM0 strap sampled at RESET_N negation. |
| 29 | VDDA33 | power_in | 3.3 V analog power supply pin. |
| 30 | USBDM_UP | bidirectional | Upstream USB data minus signal, connected to the upstream host, port, or upstream hub. |
| 31 | USBDP_UP | bidirectional | Upstream USB data plus signal, connected to the upstream host, port, or upstream hub. |
| 32 | XTALOUT | output | 24 MHz crystal output with 1.2 V p-p swing and weak (<1 mA) drive; leave unconnected when an external clock drives XTALIN/CLKIN. |
| 33 | XTALIN/CLKIN | input | 24 MHz crystal input, or external 24 MHz clock input when no crystal is used. |
| 34 | PLLFILT | passive | PLL regulator filter capacitor pin, which can take up to a 0.1 µF low-ESR capacitor to VSS or be left unconnected. |
| 35 | RBIAS | passive | USB transceiver bias pin; a 12.0 kΩ (±1%) resistor is connected from this pin to ground. |
| 36 | VDDA33 | power_in | 3.3 V analog power supply pin. |
| 37 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFN-36-EP(6x6) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 37 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 3.3 V supply voltage | VDD33, VDDA33 | 3 | 3.6 | V | Applies to all parts | 39 | |
| 3.3 V supply voltage | VDD33, VDDA33 | 4.6 | V | Applies to all packages | 39 | ||
| Storage Temperature | TSTOR | -55 | 150 | °C | 39 | ||
| Voltage on any I/O pin | -0.5 | 5.5 | V | 39 | |||
| Voltage on XTALIN | -0.5 | 4 | V | 39 | |||
| Voltage on XTALOUT | -0.5 | 2.5 | V | Note 6-1 | 39 | ||
| Extended Commercial Operating Temperature | TAE | 0 | 85 | °C | Ambient temperature in still air | 39 | |
| Voltage on any I/O pin | -0.3 | 5.5 | V | If any 3.3 V supply voltage drops below 3.0 V, then the MAX becomes (3.3 V supply voltage) + 0.5 | 39 | ||
| Voltage on XTALIN | -0.3 | V | MAX printed as VDD33 | 39 | |||
| 3.3 V supply rise time | tRT33 | 0 | 400 | µs | See Figure 6-1 and Note 6-2 | 39 | |
| Low Input Level (I, IS type) | VILI | 0.8 | V | TTL Levels | 40 | ||
| High Input Level (I, IS type) | VIHI | 2 | V | 40 | |||
| Input Leakage (I, IS type) | IIL | -10 | 10 | µA | VIN = 0 to VDD33 | 40 | |
| Hysteresis (IS only) | VHYSI | 250 | 350 | mV | IS only | 40 | |
| Low Input Level (IPU) | VILI | 0.8 | V | TTL Levels | 40 | ||
| High Input Level (IPU) | VIHI | 2 | V | 40 | |||
| Low Input Leakage (IPU) | IILL | 35 | 90 | µA | VIN = 0 | 40 | |
| High Input Leakage (IPU) | IIHL | -10 | 10 | µA | VIN = VDD33 | 40 | |
| Low Input Level (IPD) | VILI | 0.8 | V | TTL Levels | 40 | ||
| High Input Level (IPD) | VIHI | 2 | V | 40 | |||
| Low Input Leakage (IPD) | IILL | 10 | -10 | µA | VIN = 0 | 40 | |
| High Input Leakage (IPD) | IIHL | -35 | -90 | µA | VIN = VDD33 | 40 | |
| Low Input Level (ICLK) | VILCK | 0.3 | V | 40 | |||
| High Input Level (ICLK) | VIHCK | 0.9 | V | 40 | |||
| Input Leakage (ICLK) | IIL | -10 | 10 | µA | VIN = 0 to VDD33 | 40 | |
| Output Leakage (O12, I/O12, I/OSD12) | IOL | -10 | 10 | µA | Note 6-3, current pins in high impedance | 41 | |
| Low Output Level (O12, I/O12, I/OSD12) | VOL | 0.4 | V | IOL = 12 mA @ VDD33 = 3.3 V | 41 | ||
| High Output Level (O12, I/O12, I/OSD12) | VOH | 2.4 | V | IOH = -12 mA @ VDD33 = 3.3 V | 41 | ||
| Hysteresis (SD pad only) | IHYSC | 250 | 350 | mV | VIN = VDD33 (Note 6-1) | 41 | |
| Supply Current Unconfigured: Hi-Speed Host (USB2514B) | ICCINTHS | 50 | mA | Unconfigured, hi-speed host | 41 | ||
| Supply Current Configured: Hi-Speed Host, 1 port base (USB2514B) | IHCH1 | 80 | mA | Base current of one downstream port; each additional port adds 25 mA | 41 | ||
| Supply Current Configured: Full-Speed Host (USB2514B) | IFCC1 | 60 | mA | Base current of one downstream port; each additional port adds 8 mA | 42 | ||
| Supply Current Suspend (USB2514B) | ICSBY | 1200 | µA | All supplies combined | 42 | ||
| Supply Current Reset (USB2514B) | ICRST | 1400 | µA | All supplies combined | 42 | ||
| Clock Input Capacitance | CXTAL | 6 | pF | All pins except USB pins and the pins under the test tied to AC ground | 42 | ||
| Input Capacitance | CIN | 6 | pF | Note 6-5, TA = 25°C; fc = 1 MHz; VDD33 = 3.3 V | 42 | ||
| Output Capacitance | COUT | 6 | pF | Note 6-5, TA = 25°C; fc = 1 MHz; VDD33 = 3.3 V | 42 | ||
| Crystal frequency tolerance | -350 | 24 | 350 | ppm | Crystal: parallel resonant, fundamental mode, 24 MHz; typ holds nominal 24 MHz | 44 | |
| External clock frequency tolerance | -350 | 24 | 350 | ppm | External clock, 24 MHz | 45 | |
| External clock duty cycle tolerance | -10 | 50 | 10 | % | External clock duty cycle 50% ±10% | 45 | |
| RESET_N asserted | t1 | 1 | s | Minimum assertion of RESET_N after supplies within operating range | 36 | ||
| CFG_SEL[1:0] setup time | t2 | 16.7 | ns | 36 | |||
| CFG_SEL[1:0] hold time | t3 | 16.7 | 1400 | ns | 36 | ||
| Hub outputs driven to inactive logic states | t4 | 1.5 | 2 | s | 36 | ||
| Slave device timeout (master detect) | TTIMEOUT, MIN | 25 | ms | Any single clock low interval exceeding this aborts transfer | 34 | ||
| Slave device timeout (slave reset) | TTIMEOUT, MAX | 35 | ms | Slave must be able to receive new START no later than this | 34 |
CAD (KiCad official)
- Symbol:
USB2514B-AEZG-TR - Footprint:
Package_DFN_QFN:QFN-36-1EP_6x6mm_P0.5mm_EP3.7x3.7mm - 3D model: TQFN-36-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
usb2514b-aezg-tr-etched.step/usb2514b-aezg-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);usb2514b-aezg-tr.step/usb2514b-aezg-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (57 pp, sha256
3fca1a17701a3fd5, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).