main
Download ZIP Propose a change
Generated by adom_assets · KiCad file format 20240108
Name Last commit message Last updated
docs urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
viewers urb1d12ld-20wr3: viewers rendered from the public page · Ray
package.json Publish 0.1.3 · Ray
page.json Publish 0.1.3 · Ray
README.md urb1d12ld-20wr3: CAD wording names the Adom_Gen land, not KiCad official · Ray
urb1d12ld-20wr3-etched.glb urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
urb1d12ld-20wr3-etched.step urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
urb1d12ld-20wr3-hero.glb urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
urb1d12ld-20wr3-hero.overlay.json urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
urb1d12ld-20wr3.glb urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
urb1d12ld-20wr3.kicad_mod urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
urb1d12ld-20wr3.kicad_sym Publish 0.1.0 · Ray
urb1d12ld-20wr3.lbr urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
urb1d12ld-20wr3.step urb1d12ld-20wr3: footprint re-picked to YLPTEC_URB1_561e39 from the maker drawing · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 6 pins · Ray

URB1D12LD-20WR3

YLPTEC · Power Modules · DIP-6

URB1D12LD-20WR3 from YLPTEC, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 +Vin power_in Positive input terminal for the 110VDC nominal input series, operating over 40-160VDC with 180VDC surge maximum; exceeding the maximum input voltage may cause permanent damage to the module.
2 -Vin power_in Negative input terminal, which is the reference for the CTRL pin voltage.
3 CTRL input Remote on/off control: leave floating or drive with 3.5-12VDC to enable the module, or pull to 0-1.2VDC to disable it, with input current of 2 mA typ and 7 mA max while off, referenced to -Vin.
4 Trim passive Output voltage trim pin adjusted with external resistors; the trim table lists the 12 V row as R1 56 kΩ, R2 14.571 kΩ, R3 84.5 kΩ and Vref 2.5 V.
5 -Vo power_out Negative output terminal of the single 12 VDC output, which is the output return.
6 +Vo power_out Positive 12 VDC output rated 1667 mA maximum, with a maximum capacitive load of 2200 µF and ripple and noise of 50 mVp-p typ and 80 mVp-p max.

Key specifications

Parameter Value
Manufacturer YLPTEC
Package DIP-6
Category Power Management
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range (nominal 110VDC series) 40 110 160 VDC Nominal input series; range value 1
Input current, full load (12V output) 212 217 mA 110VDC nominal input series; nominal input voltage; full load 1
Input current, no load (12V output) 3 8 mA 110VDC nominal input series; nominal input voltage; no load 1
Input surge voltage (Isec.max) -0.7 180 VDC 110VDC nominal input series 2
Start-up voltage 40 VDC 110VDC nominal input series 2
Input undervoltage protection 28 33 VDC 110VDC nominal input series 2
Input current at shutdown (Ctrl) 2 7 mA 2
Remote on-level (Ctrl open or TTL high) 3.5 12 VDC Ctrl open or TTL high level (3.5-12VDC) 2
Remote off-level (Ctrl to GND or low) 0 1.2 VDC Ctrl connected to GND or low level (0-1.2VDC) 2
Output current (12V model) 0 1667 mA Product selection table, Max./Min. output current 1
Efficiency at full load 84 86 % Full load (Min./Typ. as printed) 1
Maximum capacitive load 2200 μF Maximum capacitive load on +Vo 1
Output voltage accuracy (+Vo1) -2 1 2 % Output load 0%-100%; typ printed ±1.0%, max printed ±2.0% 2
Line regulation (+Vo1) -0.5 0.2 0.5 % Input voltage range; typ printed ±0.2%, max printed ±0.5% 2
Load regulation (+Vo1) -1 0.5 1 % 20%~100% rated load, balanced load; typ printed ±0.5%, max printed ±1% 2
Ripple and noise, peak-to-peak (+Vo1) 50 80 mVp-p Pure resistive load, 20MHz bandwidth, peak-to-peak 2
Dynamic response step deviation (+Vo1) -5 3 5 % 25% nominal load step; typ printed ±3.0%, max printed ±5.0% 2
Dynamic response recovery time (+Vo1) 300 500 μs 2
Output overvoltage protection 110 160 %Vo Full voltage range input 2
Output overcurrent protection 110 150 200 %Io Full voltage range input 2
Isolation voltage 1500 VDC Input-output, 1 min test, leakage current less than 1mA 3
Insulation resistance 1000 MΩ Input-output, insulation voltage 500VDC 3
Isolation capacitance 1000 pF Input-output, 100KHz/0.1V 3
Operating temperature -40 85 ℃ Use reference temperature derating curve 3
Storage temperature -40 125 ℃ 3
Maximum case temperature in operation -55 100 ℃ 3
Storage humidity 5 95 %RH Non-condensing 3
Pin soldering temperature 300 ℃ Solder joint 1.5mm from case, 10 s 3
Recommended external capacitor C1 C1 47 100 μF General recommendation, recommended test circuit (Fig. 1) 4
Recommended external capacitors C2, C3 C2, C3 10 22 μF General recommendation, recommended test circuit (Fig. 1) 4
Minimum load with capacitive load 3 % Required when capacitive load is applied 4
Nominal output voltage 12 V Product selection table, nominal value 1
Rated output power (series) 20 W Series-wide statement 1
Reflected ripple current 40 mA Nominal input voltage 2
Start-up time 10 mS Nominal input voltage and constant-resistance load 2
Start-up delay time (+Vo1) 1 ms 2
Switching frequency 250 kHz PWM mode 3

CAD (Adom-generated)

  • Symbol: URB1D12LD-20WR3
  • Footprint: Adom_Gen:YLPTEC_URB1_561e39
  • 3D model: DIP-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 12.0 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: urb1d12ld-20wr3-etched.step / urb1d12ld-20wr3-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); urb1d12ld-20wr3.step / urb1d12ld-20wr3.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: YLPTEC datasheet (6 pp, sha256 069e99b48ea61255, retrieved 2026-11-12, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.

Datasheet PDF