component
URB1D12LD-20WR3
Public Made by Adomby adom
YLPTEC Power Modules, DIP-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownURB1D12LD-20WR3
YLPTEC · Power Modules · DIP-6
URB1D12LD-20WR3 from YLPTEC, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | +Vin | power_in | Positive input terminal for the 110VDC nominal input series, operating over 40-160VDC with 180VDC surge maximum; exceeding the maximum input voltage may cause permanent damage to the module. |
| 2 | -Vin | power_in | Negative input terminal, which is the reference for the CTRL pin voltage. |
| 3 | CTRL | input | Remote on/off control: leave floating or drive with 3.5-12VDC to enable the module, or pull to 0-1.2VDC to disable it, with input current of 2 mA typ and 7 mA max while off, referenced to -Vin. |
| 4 | Trim | passive | Output voltage trim pin adjusted with external resistors; the trim table lists the 12 V row as R1 56 kΩ, R2 14.571 kΩ, R3 84.5 kΩ and Vref 2.5 V. |
| 5 | -Vo | power_out | Negative output terminal of the single 12 VDC output, which is the output return. |
| 6 | +Vo | power_out | Positive 12 VDC output rated 1667 mA maximum, with a maximum capacitive load of 2200 µF and ripple and noise of 50 mVp-p typ and 80 mVp-p max. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | YLPTEC |
| Package | DIP-6 |
| Category | Power Management |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range (nominal 110VDC series) | 40 | 110 | 160 | VDC | Nominal input series; range value | 1 | |
| Input current, full load (12V output) | 212 | 217 | mA | 110VDC nominal input series; nominal input voltage; full load | 1 | ||
| Input current, no load (12V output) | 3 | 8 | mA | 110VDC nominal input series; nominal input voltage; no load | 1 | ||
| Input surge voltage (Isec.max) | -0.7 | 180 | VDC | 110VDC nominal input series | 2 | ||
| Start-up voltage | 40 | VDC | 110VDC nominal input series | 2 | |||
| Input undervoltage protection | 28 | 33 | VDC | 110VDC nominal input series | 2 | ||
| Input current at shutdown (Ctrl) | 2 | 7 | mA | 2 | |||
| Remote on-level (Ctrl open or TTL high) | 3.5 | 12 | VDC | Ctrl open or TTL high level (3.5-12VDC) | 2 | ||
| Remote off-level (Ctrl to GND or low) | 0 | 1.2 | VDC | Ctrl connected to GND or low level (0-1.2VDC) | 2 | ||
| Output current (12V model) | 0 | 1667 | mA | Product selection table, Max./Min. output current | 1 | ||
| Efficiency at full load | 84 | 86 | % | Full load (Min./Typ. as printed) | 1 | ||
| Maximum capacitive load | 2200 | μF | Maximum capacitive load on +Vo | 1 | |||
| Output voltage accuracy (+Vo1) | -2 | 1 | 2 | % | Output load 0%-100%; typ printed ±1.0%, max printed ±2.0% | 2 | |
| Line regulation (+Vo1) | -0.5 | 0.2 | 0.5 | % | Input voltage range; typ printed ±0.2%, max printed ±0.5% | 2 | |
| Load regulation (+Vo1) | -1 | 0.5 | 1 | % | 20%~100% rated load, balanced load; typ printed ±0.5%, max printed ±1% | 2 | |
| Ripple and noise, peak-to-peak (+Vo1) | 50 | 80 | mVp-p | Pure resistive load, 20MHz bandwidth, peak-to-peak | 2 | ||
| Dynamic response step deviation (+Vo1) | -5 | 3 | 5 | % | 25% nominal load step; typ printed ±3.0%, max printed ±5.0% | 2 | |
| Dynamic response recovery time (+Vo1) | 300 | 500 | μs | 2 | |||
| Output overvoltage protection | 110 | 160 | %Vo | Full voltage range input | 2 | ||
| Output overcurrent protection | 110 | 150 | 200 | %Io | Full voltage range input | 2 | |
| Isolation voltage | 1500 | VDC | Input-output, 1 min test, leakage current less than 1mA | 3 | |||
| Insulation resistance | 1000 | MΩ | Input-output, insulation voltage 500VDC | 3 | |||
| Isolation capacitance | 1000 | pF | Input-output, 100KHz/0.1V | 3 | |||
| Operating temperature | -40 | 85 | ℃ | Use reference temperature derating curve | 3 | ||
| Storage temperature | -40 | 125 | ℃ | 3 | |||
| Maximum case temperature in operation | -55 | 100 | ℃ | 3 | |||
| Storage humidity | 5 | 95 | %RH | Non-condensing | 3 | ||
| Pin soldering temperature | 300 | ℃ | Solder joint 1.5mm from case, 10 s | 3 | |||
| Recommended external capacitor C1 | C1 | 47 | 100 | μF | General recommendation, recommended test circuit (Fig. 1) | 4 | |
| Recommended external capacitors C2, C3 | C2, C3 | 10 | 22 | μF | General recommendation, recommended test circuit (Fig. 1) | 4 | |
| Minimum load with capacitive load | 3 | % | Required when capacitive load is applied | 4 | |||
| Nominal output voltage | 12 | V | Product selection table, nominal value | 1 | |||
| Rated output power (series) | 20 | W | Series-wide statement | 1 | |||
| Reflected ripple current | 40 | mA | Nominal input voltage | 2 | |||
| Start-up time | 10 | mS | Nominal input voltage and constant-resistance load | 2 | |||
| Start-up delay time (+Vo1) | 1 | ms | 2 | ||||
| Switching frequency | 250 | kHz | PWM mode | 3 |
CAD (Adom-generated)
- Symbol:
URB1D12LD-20WR3 - Footprint:
Adom_Gen:YLPTEC_URB1_561e39 - 3D model: DIP-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 12.0 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
urb1d12ld-20wr3-etched.step/urb1d12ld-20wr3-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);urb1d12ld-20wr3.step/urb1d12ld-20wr3.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: YLPTEC datasheet (6 pp, sha256
069e99b48ea61255, retrieved 2026-11-12, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.