main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs ucc3895dwtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers ucc3895dwtr: viewers · Ray
package.json ucc3895dwtr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json ucc3895dwtr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/ucc3895dwtr · Ray
ucc3895dwtr-etched.fit.json ucc3895dwtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
ucc3895dwtr-etched.glb ucc3895dwtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
ucc3895dwtr-etched.step ucc3895dwtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
ucc3895dwtr.glb Publish 0.1.0 · Ray
ucc3895dwtr.kicad_mod Publish 0.1.0 · Ray
ucc3895dwtr.kicad_sym Publish 0.1.0 · Ray
ucc3895dwtr.lbr Publish 0.1.0 · Ray
ucc3895dwtr.step Publish 0.1.0 · Ray

UCC3895DWTR

Texas Instruments · AC-DC Controllers And Regulators · SOIC-20-300mil

UCC3895DWTR from Texas Instruments, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EAN input Inverting input to the error amplifier; keep voltage below 3.6 V for proper operation.
2 EAOUT output Error amplifier output; internally connected to non-inverting input of PWM comparator and no-load comparator; internally clamped to soft-start voltage.
3 RAMP input Inverting input of the PWM comparator; receives CT waveform in voltage/average current-mode control or current signal with slope compensation in peak current-mode control.
4 REF power_out 5-V ±1.2% precision voltage reference output supplying up to 5 mA; bypass with 0.1-μF low-ESR low-ESL capacitor to GND; do not use more than 4.7 μF total capacitance.
5 GND power_in Analog ground for all internal circuits except output stages.
6 SYNC bidirectional Bidirectional oscillator synchronization pin; functions as clock output when used as output or overrides internal oscillator when used as input with threshold 2.05-2.4 V; can be pulled to GND with 3.9 kΩ minimum.
7 CT input Oscillator timing capacitor; oscillator charges CT via programmed current generating sawtooth waveform with peak 2.35 V; supports 100-880 pF range.
8 RT input Oscillator timing resistor for programming switching frequency; valid range 40-120 kΩ with voltage maintained at 2.9-3.1 V nominal.
9 DELAB input Delay-programming pin for dead time between OUTA and OUTB complementary outputs; external resistor sets delay per formula tDELAY = 25 ns + (25×10⁻¹² × R_DEL / V_DEL).
10 DELCD input Delay-programming pin for dead time between OUTC and OUTD complementary outputs; external resistor sets delay per formula tDELAY = 25 ns + (25×10⁻¹² × R_DEL / V_DEL).
11 ADS input Adaptive delay-set pin; sets ratio between maximum and minimum programmed output delay dead time; must be 0-2.5 V and ≤ CS voltage for proper operation.
12 CS input Current sense input for cycle-by-cycle current limiting and overcurrent protection; peak current threshold 1.9-2.1 V, overcurrent threshold 2.4-2.6 V; delay to output 75-110 ns.
13 OUTD output 100-mA complementary MOS driver output; phase-shifted relative to OUTB; optimized to drive MOSFET gate driver circuits or transformers; high-level 250-400 mV, low-level 150-250 mV at 10 mA.
14 OUTC output 100-mA complementary MOS driver output; phase-shifted relative to OUTA; optimized to drive MOSFET gate driver circuits or transformers; high-level 250-400 mV, low-level 150-250 mV at 10 mA.
15 VDD power_in Power supply input pin; operating range 10-16.5 V; bypass with minimum 1-μF low-ESR low-ESL capacitor to PGND; additional 10-μF capacitor between VDD and PGND recommended.
16 PGND power_in Output stage ground providing ground reference for high-current output drivers; must be electrically tied to GND with low-impedance connection.
17 OUTB output 100-mA complementary MOS driver output; fully complementary to OUTA operating at ≈50% duty cycle and one-half oscillator frequency; high-level 250-400 mV, low-level 150-250 mV at 10 mA.
18 OUTA output 100-mA complementary MOS driver output; drives one half-bridge circuit in external power stage; operating at ≈50% duty cycle and one-half oscillator frequency; high-level 250-400 mV, low-level 150-250 mV at 10 mA.
19 SS/DISB input Soft-start and disable pin combining two independent functions; sources current ~35 μA during soft-start mode and sinks ~350 μA during soft-stop (overcurrent) mode; threshold 0.44-0.56 V.
20 EAP input Non-inverting input to the error amplifier; keep voltage below 3.6 V for proper operation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-20-300mil
Category Power Management (PMIC)
Pins 20

CAD (KiCad official)

  • Symbol: UCC3895DWTR
  • Footprint: Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm
  • 3D model: SOIC-20-300mil (KiCad packages3D, STEP)
  • 3D model files: ucc3895dwtr-etched.step / ucc3895dwtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc3895dwtr.step / ucc3895dwtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (61 pp, sha256 839591a78c6304d9, retrieved 2026-09-22, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF