main
History Download
Ray Publish 0.1.0 a7cf282

UCC28C53DGKR

Texas Instruments · IC · VSSOP-8

UCC28C53DGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 COMP output Error amplifier output for compensation, internally current limited so that forcing COMP to GND commands zero duty cycle.
2 FB input Inverting input of the error amplifier, with the noninverting input internally trimmed to 2.5 V ±1%.
3 CS input Primary-side current sense input to the PWM comparator, connected to the current sensing resistor, which terminates OUT conduction when the sensed signal reaches the error amplifier-derived level.
4 RT/CT bidirectional Oscillator set point: timing resistor RRT connects to VREF and timing capacitor CCT connects to GND to set the switching frequency, which equals fOSC for the UCC28C53 (OUT can operate near 100% duty cycle).
5 GND power_in Ground return pin for the output driver stage and the logic-level controller section; all voltages are referenced to this pin.
6 OUT output Totem-pole gate drive output for directly driving a MOSFET, sourcing and sinking up to 1 A peak and actively held low when VDD is below the turn-on threshold.
7 VDD power_in Analog controller bias supply input with an absolute maximum of 30 V, requiring a 0.1 µF bypass capacitor connected directly to GND with minimal trace length.
8 VREF power_out 5-V reference output that must be bypassed to GND with a ceramic capacitor of at least 0.1 µF placed as close to the pin as possible, and no external voltage above the specified VREF may be applied to it.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-8
Category
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VDD VDD 30 V 5
Input current IVDD IVDD 30 mA 5
Output drive current (peak) -1 1 A 5
Output energy (capacitive load) EOUT 5 µJ 5
Analog input voltage (COMP, CS, FB, RT/CT) -0.3 6.3 V 5
Output driver voltage (OUT) -0.3 30 V 5
Reference voltage VREF 7 V 5
Error amplifier output sink current (COMP) 10 mA 5
Lead temperature (soldering) TLEAD 300 °C 10 s 5
Operating junction temperature TJ -40 150 °C 5
Storage temperature Tstg -65 150 °C 5
Input voltage VDD (recommended) VVDD 28 V 6
Output driver voltage (recommended) VOUT 28 V 6
Average output driver current IOUT 200 mA 6
Reference output current IOUT(VREF) -20 mA 6
Operating junction temperature (UCC28C5x) TJ -40 125 °C UCC28C5x 6
Junction-to-ambient thermal resistance (DGK VSSOP) RθJA 176.4 °C/W 6
Junction-to-case (top) thermal resistance (DGK VSSOP) RθJC(top) 67.3 °C/W 6
Junction-to-board thermal resistance (DGK VSSOP) RθJB 98.1 °C/W 6
VREF voltage, initial accuracy VVREF 4.95 5 5.05 V TJ = 25°C, IOUT = 1 mA 7
VREF line regulation 0.2 20 mV 12 V ≤ VVDD ≤ 25 V 7
VREF load regulation 3 25 mV 1 mA to 20 mA 7
VREF temperature stability 0.2 0.4 mV/°C 7
VREF total output variation 4.85 5.15 V 7
VREF long term stability 5 25 mV 1000 hours, TJ = 125°C 7
Output short circuit (source current) IVREF 30 45 55 mA 7
Initial oscillator frequency accuracy fOSC 50.5 53 55 kHz TJ = 25°C 7
Oscillator voltage stability 0.2 1 % 12 V ≤ VVDD ≤ 25 V 7
Oscillator temperature stability 1 2.5 % TJ(MIN) to TJ(MAX) 7
Oscillator discharge current 7.7 8.4 9 mA TJ = 25°C, VRT/CT = 2 V 7
Oscillator discharge current (over temperature) 7.2 8.4 9.5 mA VRT/CT = 2 V 7
Feedback input voltage, initial accuracy VFB 2.475 2.5 2.525 V VCOMP = 2.5 V, TJ = 25°C 7
Feedback input voltage, total variation VFB 2.45 2.5 2.55 V VCOMP = 2.5 V 7
Error amplifier input bias current (source) IFB 0.1 2 µA VFB = 5 V 7
Error amplifier open-loop voltage gain AVOL 65 90 dB 2 V ≤ VOUT ≤ 4 V 7
Error amplifier unity gain bandwidth 1 1.5 MHz 7
Error amplifier output sink current 2 14 mA VFB = 2.7 V, VCOMP = 1.1 V 7
Error amplifier output source current 0.5 1 mA VFB = 2.3 V, VCOMP = 5 V 7
Low-level COMP voltage VOL 0.1 1.1 V VFB = 2.7 V, RCOMP = 15 kΩ COMP to VREF 7
Current sense gain ACS 2.85 3 3.15 V/V 7
Current sense maximum input signal VCS 0.9 1 1.1 V VFB < 2.4 V 7
Current sense input bias current (source) ICS 0.1 2 µA 7
CS to output delay tD 35 70 ns 7
RDS(on) pulldown (VOUT low) VOUT(low) 5.5 15 Ω ISINK = 200 mA 7
RDS(on) pullup (VOUT high) VOUT(high) 10 25 Ω ISOURCE = 200 mA 7
Output rise time tRISE 25 50 ns TJ = 25°C, COUT = 1 nF 7
Output fall time tFALL 20 40 ns TJ = 25°C, COUT = 1 nF 7
Start threshold (UCCx8C53) VDDON 7.8 8.4 9 V 8
Minimum operating voltage (UCCx8C53) VDDOFF 7 7.6 8.2 V 8
UVLO hysteresis VDDON - VDDOFF (UCCx8C53) VDDHyst 0.8 0.9 V 8
Maximum duty cycle (UCCx8C52, UCCx8C53, UCCx8C50) DMAX 94 96 % VFB < 2.4 V 8
Start-up current ISTART-UP 50 75 µA VVDD = VDDON, 0.5 V 8
Operating supply current IVDD 1.3 2 mA VFB = VCS = 0 V 8

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin The inductor rising slope (Sn) at the CS pin is calculated with Equation 34. Sn = 34

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: UCC28C53DGKR
  • Footprint: Package_SO:VSSOP-8_3x3mm_P0.65mm
  • 3D model: VSSOP-8, generated on the KiCad land (body 3 x 3 mm, terminals on the pads, 1.1 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ucc28c53dgkr-etched.step / ucc28c53dgkr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc28c53dgkr.step / ucc28c53dgkr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (58 pp, sha256 d9b2cab289f0aa82, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF