Generated by kicad-footprint-generator · KiCad file format 20260206
UCC28C53DGKR
Texas Instruments · IC · VSSOP-8
UCC28C53DGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | output | Error amplifier output for compensation, internally current limited so that forcing COMP to GND commands zero duty cycle. |
| 2 | FB | input | Inverting input of the error amplifier, with the noninverting input internally trimmed to 2.5 V ±1%. |
| 3 | CS | input | Primary-side current sense input to the PWM comparator, connected to the current sensing resistor, which terminates OUT conduction when the sensed signal reaches the error amplifier-derived level. |
| 4 | RT/CT | bidirectional | Oscillator set point: timing resistor RRT connects to VREF and timing capacitor CCT connects to GND to set the switching frequency, which equals fOSC for the UCC28C53 (OUT can operate near 100% duty cycle). |
| 5 | GND | power_in | Ground return pin for the output driver stage and the logic-level controller section; all voltages are referenced to this pin. |
| 6 | OUT | output | Totem-pole gate drive output for directly driving a MOSFET, sourcing and sinking up to 1 A peak and actively held low when VDD is below the turn-on threshold. |
| 7 | VDD | power_in | Analog controller bias supply input with an absolute maximum of 30 V, requiring a 0.1 µF bypass capacitor connected directly to GND with minimal trace length. |
| 8 | VREF | power_out | 5-V reference output that must be bypassed to GND with a ceramic capacitor of at least 0.1 µF placed as close to the pin as possible, and no external voltage above the specified VREF may be applied to it. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VDD | VDD | 30 | V | 5 | |||
| Input current IVDD | IVDD | 30 | mA | 5 | |||
| Output drive current (peak) | -1 | 1 | A | 5 | |||
| Output energy (capacitive load) | EOUT | 5 | µJ | 5 | |||
| Analog input voltage (COMP, CS, FB, RT/CT) | -0.3 | 6.3 | V | 5 | |||
| Output driver voltage (OUT) | -0.3 | 30 | V | 5 | |||
| Reference voltage | VREF | 7 | V | 5 | |||
| Error amplifier output sink current (COMP) | 10 | mA | 5 | ||||
| Lead temperature (soldering) | TLEAD | 300 | °C | 10 s | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input voltage VDD (recommended) | VVDD | 28 | V | 6 | |||
| Output driver voltage (recommended) | VOUT | 28 | V | 6 | |||
| Average output driver current | IOUT | 200 | mA | 6 | |||
| Reference output current | IOUT(VREF) | -20 | mA | 6 | |||
| Operating junction temperature (UCC28C5x) | TJ | -40 | 125 | °C | UCC28C5x | 6 | |
| Junction-to-ambient thermal resistance (DGK VSSOP) | RθJA | 176.4 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance (DGK VSSOP) | RθJC(top) | 67.3 | °C/W | 6 | |||
| Junction-to-board thermal resistance (DGK VSSOP) | RθJB | 98.1 | °C/W | 6 | |||
| VREF voltage, initial accuracy | VVREF | 4.95 | 5 | 5.05 | V | TJ = 25°C, IOUT = 1 mA | 7 |
| VREF line regulation | 0.2 | 20 | mV | 12 V ≤ VVDD ≤ 25 V | 7 | ||
| VREF load regulation | 3 | 25 | mV | 1 mA to 20 mA | 7 | ||
| VREF temperature stability | 0.2 | 0.4 | mV/°C | 7 | |||
| VREF total output variation | 4.85 | 5.15 | V | 7 | |||
| VREF long term stability | 5 | 25 | mV | 1000 hours, TJ = 125°C | 7 | ||
| Output short circuit (source current) | IVREF | 30 | 45 | 55 | mA | 7 | |
| Initial oscillator frequency accuracy | fOSC | 50.5 | 53 | 55 | kHz | TJ = 25°C | 7 |
| Oscillator voltage stability | 0.2 | 1 | % | 12 V ≤ VVDD ≤ 25 V | 7 | ||
| Oscillator temperature stability | 1 | 2.5 | % | TJ(MIN) to TJ(MAX) | 7 | ||
| Oscillator discharge current | 7.7 | 8.4 | 9 | mA | TJ = 25°C, VRT/CT = 2 V | 7 | |
| Oscillator discharge current (over temperature) | 7.2 | 8.4 | 9.5 | mA | VRT/CT = 2 V | 7 | |
| Feedback input voltage, initial accuracy | VFB | 2.475 | 2.5 | 2.525 | V | VCOMP = 2.5 V, TJ = 25°C | 7 |
| Feedback input voltage, total variation | VFB | 2.45 | 2.5 | 2.55 | V | VCOMP = 2.5 V | 7 |
| Error amplifier input bias current (source) | IFB | 0.1 | 2 | µA | VFB = 5 V | 7 | |
| Error amplifier open-loop voltage gain | AVOL | 65 | 90 | dB | 2 V ≤ VOUT ≤ 4 V | 7 | |
| Error amplifier unity gain bandwidth | 1 | 1.5 | MHz | 7 | |||
| Error amplifier output sink current | 2 | 14 | mA | VFB = 2.7 V, VCOMP = 1.1 V | 7 | ||
| Error amplifier output source current | 0.5 | 1 | mA | VFB = 2.3 V, VCOMP = 5 V | 7 | ||
| Low-level COMP voltage | VOL | 0.1 | 1.1 | V | VFB = 2.7 V, RCOMP = 15 kΩ COMP to VREF | 7 | |
| Current sense gain | ACS | 2.85 | 3 | 3.15 | V/V | 7 | |
| Current sense maximum input signal | VCS | 0.9 | 1 | 1.1 | V | VFB < 2.4 V | 7 |
| Current sense input bias current (source) | ICS | 0.1 | 2 | µA | 7 | ||
| CS to output delay | tD | 35 | 70 | ns | 7 | ||
| RDS(on) pulldown (VOUT low) | VOUT(low) | 5.5 | 15 | Ω | ISINK = 200 mA | 7 | |
| RDS(on) pullup (VOUT high) | VOUT(high) | 10 | 25 | Ω | ISOURCE = 200 mA | 7 | |
| Output rise time | tRISE | 25 | 50 | ns | TJ = 25°C, COUT = 1 nF | 7 | |
| Output fall time | tFALL | 20 | 40 | ns | TJ = 25°C, COUT = 1 nF | 7 | |
| Start threshold (UCCx8C53) | VDDON | 7.8 | 8.4 | 9 | V | 8 | |
| Minimum operating voltage (UCCx8C53) | VDDOFF | 7 | 7.6 | 8.2 | V | 8 | |
| UVLO hysteresis VDDON - VDDOFF (UCCx8C53) | VDDHyst | 0.8 | 0.9 | V | 8 | ||
| Maximum duty cycle (UCCx8C52, UCCx8C53, UCCx8C50) | DMAX | 94 | 96 | % | VFB < 2.4 V | 8 | |
| Start-up current | ISTART-UP | 50 | 75 | µA | VVDD = VDDON, 0.5 V | 8 | |
| Operating supply current | IVDD | 1.3 | 2 | mA | VFB = VCS = 0 V | 8 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | The inductor rising slope (Sn) at the CS pin is calculated with Equation 34. Sn = | 34 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
UCC28C53DGKR - Footprint:
Package_SO:VSSOP-8_3x3mm_P0.65mm - 3D model: VSSOP-8, generated on the KiCad land (body 3 x 3 mm, terminals on the pads, 1.1 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ucc28c53dgkr-etched.step/ucc28c53dgkr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc28c53dgkr.step/ucc28c53dgkr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (58 pp, sha256
d9b2cab289f0aa82, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).