main
Ray
Publish 0.1.0
b9f1a8e
UCC28C45DGKR
Texas Instruments · AC-DC Controllers And Regulators · VSSOP-8
UCC28C45DGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | output | Error amplifier output for compensation, internally current limited so zero duty cycle is commanded by forcing COMP to GND, with an absolute maximum error amplifier output sink current of 10 mA. |
| 2 | FB | input | Inverting input of the error amplifier used for voltage-feedback loop stability, with the noninverting input internally trimmed to 2.5 V ±1%. |
| 3 | CS | input | Primary-side current sense input to the PWM comparator, where the maximum input signal is 1 V typical (0.9 V minimum, 1.1 V maximum) and the absolute maximum analog input range is -0.3 V to 6.3 V. |
| 4 | RT/CT | bidirectional | Oscillator set point, with timing resistor RRT connected to VREF and timing capacitor CCT connected to GND; the absolute maximum analog input voltage is -0.3 V to 6.3 V. |
| 5 | GND | power_in | Ground return for the output driver stage and the logic-level controller section; all device voltages are referenced to this pin. |
| 6 | OUT | output | Totem-pole gate drive output for directly driving a MOSFET, sourcing and sinking up to ±1 A peak, with an absolute maximum output driver voltage of 20 V, and held low when VDD is below the turn-on threshold. |
| 7 | VDD | power_in | Analog controller bias input with an absolute maximum of 20 V and a recommended input voltage of 18 V, requiring a ceramic bypass of at least 0.1 µF to GND located close to the pin. |
| 8 | VREF | power_out | 5 V reference output that must be bypassed to GND with a ceramic capacitor of at least 0.1 µF placed as close to the pin as possible, with a short-circuit source current of 30 to 55 mA and a recommended output current of up to 20 mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VDD | VDD | 20 | V | 5 | |||
| Input current IVDD | IVDD | 30 | mA | 5 | |||
| Output drive current (peak) | -1 | 1 | A | 5 | |||
| Output energy (capacitive load), EOUT | EOUT | 5 | µJ | 5 | |||
| Analog input voltage COMP, CS, FB, RT/CT | -0.3 | 6.3 | V | 5 | |||
| Output driver voltage OUT | -0.3 | 20 | V | 5 | |||
| Reference voltage VREF | VREF | 7 | V | 5 | |||
| Error amplifier output sink current COMP | 10 | mA | 5 | ||||
| Lead temperature (soldering, 10 s) | TLEAD | 300 | °C | soldering, 10 s | 5 | ||
| Operating junction temperature | TJ | -55 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input voltage | VVDD | 18 | V | 6 | |||
| Output driver voltage | VOUT | 18 | V | 6 | |||
| Maximum continuous voltage from external circuitry | VREF | 5.5 | V | 6 | |||
| Average output driver current (source and sink) | IOUT | 200 | mA | 6 | |||
| Reference output current (source) | IOUT(VREF) | 20 | mA | 6 | |||
| Operating junction temperature, UCC28C4x | TJ | -40 | 125 | °C | UCC28C4x | 6 | |
| VREF voltage, initial accuracy | VVREF | 4.9 | 5 | 5.1 | V | TJ = 25°C, IOUT = 1mA | 7 |
| Line regulation | 0.2 | 20 | mV | VVDD = 12V to 18V | 7 | ||
| Load regulation | 3 | 25 | mV | 1mA to 20mA | 7 | ||
| Temperature stability | 0.2 | 0.4 | mV/°C | See (2) | 7 | ||
| Total output variation | 4.82 | 5.18 | V | See (2) | 7 | ||
| Long term stability | 5 | 25 | mV | 1000 hours, TJ = 125°C, see (2) | 7 | ||
| Output short circuit (source current) | IVREF | 30 | 45 | 55 | mA | 7 | |
| Oscillator initial accuracy | fOSC | 50.5 | 53 | 55 | kHz | TJ = 25°C, see (3) | 7 |
| Oscillator voltage stability | 0.2 | 1 | % | 12V ≤ VVDD ≤18V | 7 | ||
| Oscillator temperature stability | 1 | 2.5 | % | TJ(MIN) to TJ(MAX), see (2) | 7 | ||
| Oscillator discharge current | 7.7 | 8.4 | 9 | mA | TJ = 25°C, VRT/CT = 2V, see (4) | 7 | |
| Oscillator discharge current | 7.2 | 8.4 | 9.5 | mA | VRT/CT = 2V, see (4) | 7 | |
| VFB feedback input voltage, initial accuracy | VFB | 2.475 | 2.5 | 2.525 | V | VCOMP = 2.5V, TJ = 25°C | 7 |
| Feedback input voltage, total variation | VFB | 2.45 | 2.5 | 2.55 | V | VCOMP = 2.5V | 7 |
| Input bias current (source current) | IFB | 0.1 | 2 | µA | VFB = 5V | 7 | |
| Open-loop voltage gain | AVOL | 65 | 90 | dB | 2V ≤ VOUT ≤ 4V | 7 | |
| Unity gain bandwidth | 1 | 1.5 | MHz | See (2) | 7 | ||
| Output sink current | 2 | 14 | mA | VFB = 2.7V, VCOMP = 1.1V | 7 | ||
| Output source current | 0.5 | 1 | mA | VFB = 2.3V, VCOMP = 5V | 7 | ||
| Low-level COMP voltage | VOL | 0.1 | 1.1 | V | VFB = 2.7V, RCOMP = 15kΩ COMP to VREF | 7 | |
| Gain | ACS | 2.85 | 3 | 3.15 | V/V | See (5) (6) | 8 |
| Maximum input signal | VCS | 0.9 | 1 | 1.1 | V | VFB < 2.4V | 8 |
| Input bias current (source current) | ICS | 0.1 | 2 | µA | 8 | ||
| CS to output delay | tD | 35 | 70 | ns | 8 | ||
| RDS(on) pulldown | VOUT(low) | 5.5 | 15 | Ω | ISINK = 200mA | 8 | |
| RDS(on) pullup | VOUT(high) | 10 | 25 | Ω | ISOURCE = 200mA | 8 | |
| Rise time | tRISE | 25 | 50 | ns | TJ = 25°C, COUT = 1nF | 8 | |
| Fall time | tFALL | 20 | 40 | ns | TJ = 25°C, COUT = 1nF | 8 | |
| Start threshold (UCCx8C43, UCCx8C45) | VDDON | 7.8 | 8.4 | 9 | V | UCCx8C43, UCCx8C45 | 8 |
| Minimum operating voltage (UCCx8C43, UCCx8C45) | VDDOFF | 7 | 7.6 | 8.2 | V | UCCx8C43, UCCx8C45 | 8 |
| Maximum duty cycle (UCCx8C45) | DMAX | 47 | 48 | % | UCCx8C44, UCCx8C45, UCCx8C41, VFB < 2.4 V | 8 | |
| Start-up current | ISTART-UP | 50 | 100 | µA | VVDD = VDDON, 0.5V | 8 | |
| Operating supply current | IVDD | 2.3 | 3 | mA | VFB = VCS = 0V | 8 | |
| Junction-to-ambient thermal resistance (DGK) | RθJA | 176.4 | °C/W | DGK (VSSOP) 8-pin column | 7 | ||
| Junction-to-case (top) thermal resistance (DGK) | RθJC(top) | 67.3 | °C/W | DGK (VSSOP) 8-pin column | 7 | ||
| Junction-to-board thermal resistance (DGK) | RθJB | 98.1 | °C/W | DGK (VSSOP) 8-pin column | 7 | ||
| Junction-to-top characterization parameter (DGK) | ψJT | 11.1 | °C/W | DGK (VSSOP) 8-pin column | 7 | ||
| Junction-to-board characterization parameter (DGK) | ψJB | 91.5 | °C/W | DGK (VSSOP) 8-pin column | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | The inductor rising slope (Sn) at the CS pin is calculated with Equation 34. Sn = | 33 |
CAD (KiCad official)
- Symbol:
UCC28C45DGKR - Footprint:
Package_SO:VSSOP-8_3x3mm_P0.65mm - 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ucc28c45dgkr-etched.step/ucc28c45dgkr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc28c45dgkr.step/ucc28c45dgkr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (60 pp, sha256
737b5e05fe02b31b, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# UCC28C45DGKR
**Texas Instruments** · AC-DC Controllers And Regulators · VSSOP-8
UCC28C45DGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | output | Error amplifier output for compensation, internally current limited so zero duty cycle is commanded by forcing COMP to GND, with an absolute maximum error amplifier output sink current of 10 mA. |
| 2 | FB | input | Inverting input of the error amplifier used for voltage-feedback loop stability, with the noninverting input internally trimmed to 2.5 V ±1%. |
| 3 | CS | input | Primary-side current sense input to the PWM comparator, where the maximum input signal is 1 V typical (0.9 V minimum, 1.1 V maximum) and the absolute maximum analog input range is -0.3 V to 6.3 V. |
| 4 | RT/CT | bidirectional | Oscillator set point, with timing resistor RRT connected to VREF and timing capacitor CCT connected to GND; the absolute maximum analog input voltage is -0.3 V to 6.3 V. |
| 5 | GND | power_in | Ground return for the output driver stage and the logic-level controller section; all device voltages are referenced to this pin. |
| 6 | OUT | output | Totem-pole gate drive output for directly driving a MOSFET, sourcing and sinking up to ±1 A peak, with an absolute maximum output driver voltage of 20 V, and held low when VDD is below the turn-on threshold. |
| 7 | VDD | power_in | Analog controller bias input with an absolute maximum of 20 V and a recommended input voltage of 18 V, requiring a ceramic bypass of at least 0.1 µF to GND located close to the pin. |
| 8 | VREF | power_out | 5 V reference output that must be bypassed to GND with a ceramic capacitor of at least 0.1 µF placed as close to the pin as possible, with a short-circuit source current of 30 to 55 mA and a recommended output current of up to 20 mA. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VDD | VDD | | | 20 | V | | 5 |
| Input current IVDD | IVDD | | | 30 | mA | | 5 |
| Output drive current (peak) | | -1 | | 1 | A | | 5 |
| Output energy (capacitive load), EOUT | EOUT | | | 5 | µJ | | 5 |
| Analog input voltage COMP, CS, FB, RT/CT | | -0.3 | | 6.3 | V | | 5 |
| Output driver voltage OUT | | -0.3 | | 20 | V | | 5 |
| Reference voltage VREF | VREF | | | 7 | V | | 5 |
| Error amplifier output sink current COMP | | | | 10 | mA | | 5 |
| Lead temperature (soldering, 10 s) | TLEAD | | | 300 | °C | soldering, 10 s | 5 |
| Operating junction temperature | TJ | -55 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 5 |
| Input voltage | VVDD | | | 18 | V | | 6 |
| Output driver voltage | VOUT | | | 18 | V | | 6 |
| Maximum continuous voltage from external circuitry | VREF | | | 5.5 | V | | 6 |
| Average output driver current (source and sink) | IOUT | | | 200 | mA | | 6 |
| Reference output current (source) | IOUT(VREF) | | | 20 | mA | | 6 |
| Operating junction temperature, UCC28C4x | TJ | -40 | | 125 | °C | UCC28C4x | 6 |
| VREF voltage, initial accuracy | VVREF | 4.9 | 5 | 5.1 | V | TJ = 25°C, IOUT = 1mA | 7 |
| Line regulation | | | 0.2 | 20 | mV | VVDD = 12V to 18V | 7 |
| Load regulation | | | 3 | 25 | mV | 1mA to 20mA | 7 |
| Temperature stability | | | 0.2 | 0.4 | mV/°C | See (2) | 7 |
| Total output variation | | 4.82 | | 5.18 | V | See (2) | 7 |
| Long term stability | | | 5 | 25 | mV | 1000 hours, TJ = 125°C, see (2) | 7 |
| Output short circuit (source current) | IVREF | 30 | 45 | 55 | mA | | 7 |
| Oscillator initial accuracy | fOSC | 50.5 | 53 | 55 | kHz | TJ = 25°C, see (3) | 7 |
| Oscillator voltage stability | | | 0.2 | 1 | % | 12V ≤ VVDD ≤18V | 7 |
| Oscillator temperature stability | | | 1 | 2.5 | % | TJ(MIN) to TJ(MAX), see (2) | 7 |
| Oscillator discharge current | | 7.7 | 8.4 | 9 | mA | TJ = 25°C, VRT/CT = 2V, see (4) | 7 |
| Oscillator discharge current | | 7.2 | 8.4 | 9.5 | mA | VRT/CT = 2V, see (4) | 7 |
| VFB feedback input voltage, initial accuracy | VFB | 2.475 | 2.5 | 2.525 | V | VCOMP = 2.5V, TJ = 25°C | 7 |
| Feedback input voltage, total variation | VFB | 2.45 | 2.5 | 2.55 | V | VCOMP = 2.5V | 7 |
| Input bias current (source current) | IFB | | 0.1 | 2 | µA | VFB = 5V | 7 |
| Open-loop voltage gain | AVOL | 65 | 90 | | dB | 2V ≤ VOUT ≤ 4V | 7 |
| Unity gain bandwidth | | 1 | 1.5 | | MHz | See (2) | 7 |
| Output sink current | | 2 | 14 | | mA | VFB = 2.7V, VCOMP = 1.1V | 7 |
| Output source current | | 0.5 | 1 | | mA | VFB = 2.3V, VCOMP = 5V | 7 |
| Low-level COMP voltage | VOL | | 0.1 | 1.1 | V | VFB = 2.7V, RCOMP = 15kΩ COMP to VREF | 7 |
| Gain | ACS | 2.85 | 3 | 3.15 | V/V | See (5) (6) | 8 |
| Maximum input signal | VCS | 0.9 | 1 | 1.1 | V | VFB < 2.4V | 8 |
| Input bias current (source current) | ICS | | 0.1 | 2 | µA | | 8 |
| CS to output delay | tD | | 35 | 70 | ns | | 8 |
| RDS(on) pulldown | VOUT(low) | | 5.5 | 15 | Ω | ISINK = 200mA | 8 |
| RDS(on) pullup | VOUT(high) | | 10 | 25 | Ω | ISOURCE = 200mA | 8 |
| Rise time | tRISE | | 25 | 50 | ns | TJ = 25°C, COUT = 1nF | 8 |
| Fall time | tFALL | | 20 | 40 | ns | TJ = 25°C, COUT = 1nF | 8 |
| Start threshold (UCCx8C43, UCCx8C45) | VDDON | 7.8 | 8.4 | 9 | V | UCCx8C43, UCCx8C45 | 8 |
| Minimum operating voltage (UCCx8C43, UCCx8C45) | VDDOFF | 7 | 7.6 | 8.2 | V | UCCx8C43, UCCx8C45 | 8 |
| Maximum duty cycle (UCCx8C45) | DMAX | 47 | | 48 | % | UCCx8C44, UCCx8C45, UCCx8C41, VFB < 2.4 V | 8 |
| Start-up current | ISTART-UP | | 50 | 100 | µA | VVDD = VDDON, 0.5V | 8 |
| Operating supply current | IVDD | | 2.3 | 3 | mA | VFB = VCS = 0V | 8 |
| Junction-to-ambient thermal resistance (DGK) | RθJA | | 176.4 | | °C/W | DGK (VSSOP) 8-pin column | 7 |
| Junction-to-case (top) thermal resistance (DGK) | RθJC(top) | | 67.3 | | °C/W | DGK (VSSOP) 8-pin column | 7 |
| Junction-to-board thermal resistance (DGK) | RθJB | | 98.1 | | °C/W | DGK (VSSOP) 8-pin column | 7 |
| Junction-to-top characterization parameter (DGK) | ψJT | | 11.1 | | °C/W | DGK (VSSOP) 8-pin column | 7 |
| Junction-to-board characterization parameter (DGK) | ψJB | | 91.5 | | °C/W | DGK (VSSOP) 8-pin column | 7 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | The inductor rising slope (Sn) at the CS pin is calculated with Equation 34. Sn = | 33 |
## CAD (KiCad official)
- Symbol: `UCC28C45DGKR`
- Footprint: `Package_SO:VSSOP-8_3x3mm_P0.65mm`
- 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `ucc28c45dgkr-etched.step` / `ucc28c45dgkr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc28c45dgkr.step` / `ucc28c45dgkr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc28c45.pdf) (60 pp, sha256 `737b5e05fe02b31b`, retrieved 2026-11-11, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ucc28c45dgkr-datasheet.pdf)