Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

UCC28C45DGKR

Texas Instruments · AC-DC Controllers And Regulators · VSSOP-8

UCC28C45DGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 COMP output Error amplifier output for compensation, internally current limited so zero duty cycle is commanded by forcing COMP to GND, with an absolute maximum error amplifier output sink current of 10 mA.
2 FB input Inverting input of the error amplifier used for voltage-feedback loop stability, with the noninverting input internally trimmed to 2.5 V ±1%.
3 CS input Primary-side current sense input to the PWM comparator, where the maximum input signal is 1 V typical (0.9 V minimum, 1.1 V maximum) and the absolute maximum analog input range is -0.3 V to 6.3 V.
4 RT/CT bidirectional Oscillator set point, with timing resistor RRT connected to VREF and timing capacitor CCT connected to GND; the absolute maximum analog input voltage is -0.3 V to 6.3 V.
5 GND power_in Ground return for the output driver stage and the logic-level controller section; all device voltages are referenced to this pin.
6 OUT output Totem-pole gate drive output for directly driving a MOSFET, sourcing and sinking up to ±1 A peak, with an absolute maximum output driver voltage of 20 V, and held low when VDD is below the turn-on threshold.
7 VDD power_in Analog controller bias input with an absolute maximum of 20 V and a recommended input voltage of 18 V, requiring a ceramic bypass of at least 0.1 µF to GND located close to the pin.
8 VREF power_out 5 V reference output that must be bypassed to GND with a ceramic capacitor of at least 0.1 µF placed as close to the pin as possible, with a short-circuit source current of 30 to 55 mA and a recommended output current of up to 20 mA.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-8
Category Power Management (PMIC)
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VDD VDD 20 V 5
Input current IVDD IVDD 30 mA 5
Output drive current (peak) -1 1 A 5
Output energy (capacitive load), EOUT EOUT 5 µJ 5
Analog input voltage COMP, CS, FB, RT/CT -0.3 6.3 V 5
Output driver voltage OUT -0.3 20 V 5
Reference voltage VREF VREF 7 V 5
Error amplifier output sink current COMP 10 mA 5
Lead temperature (soldering, 10 s) TLEAD 300 °C soldering, 10 s 5
Operating junction temperature TJ -55 150 °C 5
Storage temperature Tstg -65 150 °C 5
Input voltage VVDD 18 V 6
Output driver voltage VOUT 18 V 6
Maximum continuous voltage from external circuitry VREF 5.5 V 6
Average output driver current (source and sink) IOUT 200 mA 6
Reference output current (source) IOUT(VREF) 20 mA 6
Operating junction temperature, UCC28C4x TJ -40 125 °C UCC28C4x 6
VREF voltage, initial accuracy VVREF 4.9 5 5.1 V TJ = 25°C, IOUT = 1mA 7
Line regulation 0.2 20 mV VVDD = 12V to 18V 7
Load regulation 3 25 mV 1mA to 20mA 7
Temperature stability 0.2 0.4 mV/°C See (2) 7
Total output variation 4.82 5.18 V See (2) 7
Long term stability 5 25 mV 1000 hours, TJ = 125°C, see (2) 7
Output short circuit (source current) IVREF 30 45 55 mA 7
Oscillator initial accuracy fOSC 50.5 53 55 kHz TJ = 25°C, see (3) 7
Oscillator voltage stability 0.2 1 % 12V ≤ VVDD ≤18V 7
Oscillator temperature stability 1 2.5 % TJ(MIN) to TJ(MAX), see (2) 7
Oscillator discharge current 7.7 8.4 9 mA TJ = 25°C, VRT/CT = 2V, see (4) 7
Oscillator discharge current 7.2 8.4 9.5 mA VRT/CT = 2V, see (4) 7
VFB feedback input voltage, initial accuracy VFB 2.475 2.5 2.525 V VCOMP = 2.5V, TJ = 25°C 7
Feedback input voltage, total variation VFB 2.45 2.5 2.55 V VCOMP = 2.5V 7
Input bias current (source current) IFB 0.1 2 µA VFB = 5V 7
Open-loop voltage gain AVOL 65 90 dB 2V ≤ VOUT ≤ 4V 7
Unity gain bandwidth 1 1.5 MHz See (2) 7
Output sink current 2 14 mA VFB = 2.7V, VCOMP = 1.1V 7
Output source current 0.5 1 mA VFB = 2.3V, VCOMP = 5V 7
Low-level COMP voltage VOL 0.1 1.1 V VFB = 2.7V, RCOMP = 15kΩ COMP to VREF 7
Gain ACS 2.85 3 3.15 V/V See (5) (6) 8
Maximum input signal VCS 0.9 1 1.1 V VFB < 2.4V 8
Input bias current (source current) ICS 0.1 2 µA 8
CS to output delay tD 35 70 ns 8
RDS(on) pulldown VOUT(low) 5.5 15 Ω ISINK = 200mA 8
RDS(on) pullup VOUT(high) 10 25 Ω ISOURCE = 200mA 8
Rise time tRISE 25 50 ns TJ = 25°C, COUT = 1nF 8
Fall time tFALL 20 40 ns TJ = 25°C, COUT = 1nF 8
Start threshold (UCCx8C43, UCCx8C45) VDDON 7.8 8.4 9 V UCCx8C43, UCCx8C45 8
Minimum operating voltage (UCCx8C43, UCCx8C45) VDDOFF 7 7.6 8.2 V UCCx8C43, UCCx8C45 8
Maximum duty cycle (UCCx8C45) DMAX 47 48 % UCCx8C44, UCCx8C45, UCCx8C41, VFB < 2.4 V 8
Start-up current ISTART-UP 50 100 µA VVDD = VDDON, 0.5V 8
Operating supply current IVDD 2.3 3 mA VFB = VCS = 0V 8
Junction-to-ambient thermal resistance (DGK) RθJA 176.4 °C/W DGK (VSSOP) 8-pin column 7
Junction-to-case (top) thermal resistance (DGK) RθJC(top) 67.3 °C/W DGK (VSSOP) 8-pin column 7
Junction-to-board thermal resistance (DGK) RθJB 98.1 °C/W DGK (VSSOP) 8-pin column 7
Junction-to-top characterization parameter (DGK) ψJT 11.1 °C/W DGK (VSSOP) 8-pin column 7
Junction-to-board characterization parameter (DGK) ψJB 91.5 °C/W DGK (VSSOP) 8-pin column 7

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin The inductor rising slope (Sn) at the CS pin is calculated with Equation 34. Sn = 33

CAD (KiCad official)

  • Symbol: UCC28C45DGKR
  • Footprint: Package_SO:VSSOP-8_3x3mm_P0.65mm
  • 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ucc28c45dgkr-etched.step / ucc28c45dgkr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc28c45dgkr.step / ucc28c45dgkr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (60 pp, sha256 737b5e05fe02b31b, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF