← Commit history

Initial commit: component/ucc2897apwr

Ray ·dfdc13f5df ·
2 files changed +271
README.mdadded+56
@@ -0,0 +1,56 @@+# UCC2897APWR++**Texas Instruments** · AC-DC Controllers And Regulators · TSSOP-20++UCC2897APWR from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIN | power_in | Connect to input-power rail (maximum 120 V) to provide high-voltage JFET start-up current until bootstrap bias becomes available. |+| 2 | N/C | unconnected | No internal connection; leave floating. |+| 3 | RDEL | input | Program turn-on delay for gate-drive outputs via resistor to GND; delay time follows equation tDEL = 11.1×10⁻¹² × RDEL + 15×10⁻⁹ seconds. |+| 4 | RON | input | Program internal timing-capacitor charge current via resistor to GND; determines on-time and switching frequency along with ROFF. |+| 5 | ROFF | input | Program internal timing-capacitor discharge current via resistor to GND; determines off-time and maximum duty cycle along with RON. |+| 6 | VREF | power_out | 5-V regulated reference voltage output (up to 5 mA); bypass to GND with 0.1-µF capacitor for stability and noise filtering. |+| 7 | SYNC | bidirectional | Bidirectional synchronization input/output; accepts external clock synchronization signal or outputs internal oscillator timing reference when standalone. |+| 8 | GND | power_in | Analog ground reference for control circuitry; connect directly to PGND via single short trace to minimize control noise coupling. |+| 9 | CS | input | Peak current-sense input for current-mode control and cycle-by-cycle current limiting at 0.5-V threshold; requires RC filter between current-sense resistor and pin. |+| 10 | RSLOPE | input | Program slope-compensation current amplitude via resistor to GND; compensation slope is proportional to internal timing-capacitor waveform during OUT high periods. |+| 11 | FB | input | Error signal feedback from external optocoupler or error amplifier with control range 2.5 V (minimum duty) to 4.5 V (maximum duty). |+| 12 | SS/SD | input | Soft-start and shutdown capacitor pin; charged from 2.5 V to 4.5 V by internal current source during soft-start and discharged to 0.5 V for shutdown. |+| 13 | PGND | power_in | Power ground current return for high-current drivers OUT and AUX; must connect to GND pin with single short trace. |+| 14 | AUX | output | Gate driver output for auxiliary P-channel clamp MOSFET (active-low logic) with 2-A source and 2-A sink current capability. |+| 15 | OUT | output | Gate driver output for main N-channel MOSFET (active-high logic) with 2-A source and 2-A sink current capability; connect 10-kΩ resistor to PGND. |+| 16 | PVDD | power_in | Supply for output drivers; bypass to PGND with 10-µF capacitor at device. |+| 17 | VDD | power_in | Primary power supply (8.5 V to 16 V) for gate drivers and 5-V bias regulator; bypass to PGND with 1-µF capacitor at device. |+| 18 | LINEUV | input | Line undervoltage monitor input (1.27-V threshold, programmable hysteresis) for bulk voltage monitoring via external resistor divider. |+| 19 | LINEOV | input | Line overvoltage monitor input (1.27-V threshold, programmable hysteresis) that disables outputs immediately upon threshold crossing. |+| 20 | N/C | unconnected | No internal connection; leave floating. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-20 |+| Category | Power Management (PMIC) |+| Pins | 20 |++## CAD (KiCad official)++- Symbol: `UCC2897APWR`+- Footprint: `Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm`+- 3D model: TSSOP-20 (KiCad packages3D, STEP)+- 3D model files: `ucc2897apwr-etched.step` / `ucc2897apwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2897apwr.step` / `ucc2897apwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc2897a.pdf) (50 pp, sha256 `fb294981fe94b45c`, retrieved 2026-09-23, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc2897apwr-datasheet.pdf)
page.jsonadded+215
@@ -0,0 +1,215 @@+{+  "slug": "ucc2897apwr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments AC-DC Controllers And Regulators, TSSOP-20. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "ucc2897apwr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ucc2897apwr.kicad_sym",+    "ucc2897apwr.kicad_mod",+    "ucc2897apwr.glb",+    "ucc2897apwr.step",+    "ucc2897apwr.lbr",+    "docs/hero.png",+    "docs/ucc2897apwr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "UCC2897APWR",+    "manufacturer": "Texas Instruments",+    "package": "TSSOP-20",+    "pin_count": 20,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://www.ti.com/lit/ds/symlink/ucc2897a.pdf",+    "parts": {+      "symbol": "ucc2897apwr.kicad_sym",+      "footprint": "ucc2897apwr.kicad_mod",+      "model_3d": "ucc2897apwr-etched.glb",+      "model_3d_plain": "ucc2897apwr.glb",+      "model_3d_step": "ucc2897apwr-etched.step",+      "model_3d_step_plain": "ucc2897apwr.step",+      "lbr": "ucc2897apwr.lbr"+    },+    "distributor_links": {+      "lcsc": "C54444"+    },+    "pins": [+      {+        "number": "1",+        "name": "VIN",+        "type": "power_in",+        "description": "Connect to input-power rail (maximum 120 V) to provide high-voltage JFET start-up current until bootstrap bias becomes available."+      },+      {+        "number": "2",+        "name": "N/C",+        "type": "unconnected",+        "description": "No internal connection; leave floating."+      },+      {+        "number": "3",+        "name": "RDEL",+        "type": "input",+        "description": "Program turn-on delay for gate-drive outputs via resistor to GND; delay time follows equation tDEL = 11.1×10⁻¹² × RDEL + 15×10⁻⁹ seconds."+      },+      {+        "number": "4",+        "name": "RON",+        "type": "input",+        "description": "Program internal timing-capacitor charge current via resistor to GND; determines on-time and switching frequency along with ROFF."+      },+      {+        "number": "5",+        "name": "ROFF",+        "type": "input",+        "description": "Program internal timing-capacitor discharge current via resistor to GND; determines off-time and maximum duty cycle along with RON."+      },+      {+        "number": "6",+        "name": "VREF",+        "type": "power_out",+        "description": "5-V regulated reference voltage output (up to 5 mA); bypass to GND with 0.1-µF capacitor for stability and noise filtering."+      },+      {+        "number": "7",+        "name": "SYNC",+        "type": "bidirectional",+        "description": "Bidirectional synchronization input/output; accepts external clock synchronization signal or outputs internal oscillator timing reference when standalone."+      },+      {+        "number": "8",+        "name": "GND",+        "type": "power_in",+        "description": "Analog ground reference for control circuitry; connect directly to PGND via single short trace to minimize control noise coupling."+      },+      {+        "number": "9",+        "name": "CS",+        "type": "input",+        "description": "Peak current-sense input for current-mode control and cycle-by-cycle current limiting at 0.5-V threshold; requires RC filter between current-sense resistor and pin."+      },+      {+        "number": "10",+        "name": "RSLOPE",+        "type": "input",+        "description": "Program slope-compensation current amplitude via resistor to GND; compensation slope is proportional to internal timing-capacitor waveform during OUT high periods."+      },+      {+        "number": "11",+        "name": "FB",+        "type": "input",+        "description": "Error signal feedback from external optocoupler or error amplifier with control range 2.5 V (minimum duty) to 4.5 V (maximum duty)."+      },+      {+        "number": "12",+        "name": "SS/SD",+        "type": "input",+        "description": "Soft-start and shutdown capacitor pin; charged from 2.5 V to 4.5 V by internal current source during soft-start and discharged to 0.5 V for shutdown."+      },+      {+        "number": "13",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground current return for high-current drivers OUT and AUX; must connect to GND pin with single short trace."+      },+      {+        "number": "14",+        "name": "AUX",+        "type": "output",+        "description": "Gate driver output for auxiliary P-channel clamp MOSFET (active-low logic) with 2-A source and 2-A sink current capability."+      },+      {+        "number": "15",+        "name": "OUT",+        "type": "output",+        "description": "Gate driver output for main N-channel MOSFET (active-high logic) with 2-A source and 2-A sink current capability; connect 10-kΩ resistor to PGND."+      },+      {+        "number": "16",+        "name": "PVDD",+        "type": "power_in",+        "description": "Supply for output drivers; bypass to PGND with 10-µF capacitor at device."+      },+      {+        "number": "17",+        "name": "VDD",+        "type": "power_in",+        "description": "Primary power supply (8.5 V to 16 V) for gate drivers and 5-V bias regulator; bypass to PGND with 1-µF capacitor at device."+      },+      {+        "number": "18",+        "name": "LINEUV",+        "type": "input",+        "description": "Line undervoltage monitor input (1.27-V threshold, programmable hysteresis) for bulk voltage monitoring via external resistor divider."+      },+      {+        "number": "19",+        "name": "LINEOV",+        "type": "input",+        "description": "Line overvoltage monitor input (1.27-V threshold, programmable hysteresis) that disables outputs immediately upon threshold crossing."+      },+      {+        "number": "20",+        "name": "N/C",+        "type": "unconnected",+        "description": "No internal connection; leave floating."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Pin 3 nomenclature: Datasheet shows 'RTDEL' in the Pin Functions table (page 4) but all other refere"+        ],+        "pages_sent": 50,+        "cost_usd": 0.4964,+        "at": "2026-09-23T07:05:17"+      },+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/ucc2897a.pdf",+        "pages": 50,+        "sha256": "fb294981fe94b45c",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 20,+        "described": 20,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file