main
Ray
Publish 0.1.0
93a4fa3
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291
{
"slug": "ucc2894pw",
"version": "0.1.0",
"type": "component",
"description": "Texas Instruments DC-DC Controllers, TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
"tags": [
"component",
"power supply chip",
"ucc2894pw",
"factory-2.0.0",
"extractor-text"
],
"dependencies": {},
"hero": {
"type": "image",
"path": "docs/hero.png"
},
"files": [
"page.json",
"README.md",
"ucc2894pw.kicad_sym",
"ucc2894pw.kicad_mod",
"ucc2894pw.glb",
"ucc2894pw.step",
"ucc2894pw.lbr",
"docs/hero.png",
"docs/ucc2894pw-datasheet.pdf",
"viewers/symbol.html",
"viewers/footprint.html",
"ucc2894pw-hero.glb",
"ucc2894pw-hero.overlay.json",
"ucc2894pw-etched.glb"
],
"component": {
"mpn": "UCC2894PW",
"manufacturer": "Texas Instruments",
"package": "TSSOP-16",
"pin_count": 16,
"category": "Power Supply Chip",
"subcategory": "DC-DC Controllers",
"datasheet": "https://www.ti.com/lit/ds/symlink/ucc2894.pdf",
"parts": {
"symbol": "ucc2894pw.kicad_sym",
"footprint": "ucc2894pw.kicad_mod",
"model_3d": "ucc2894pw-hero.glb",
"model_3d_plain": "ucc2894pw-etched.glb",
"model_3d_step": "ucc2894pw-etched.step",
"model_3d_step_plain": "ucc2894pw.step",
"lbr": "ucc2894pw.lbr"
},
"distributor_links": {
"lcsc": "C2867492",
"digikey": "296-15888-5-ND",
"mouser": "595-UCC2894PW"
},
"distributor_check": {
"checked_at": "2026-10-31T00:46:21Z",
"source": "Component Ocean /api/assign-pns",
"digikey": {
"pn": "296-15888-5-ND",
"status": "found",
"lifecycle": "Active"
},
"mouser": {
"pn": "595-UCC2894PW",
"status": "found"
}
},
"pins": [
{
"number": "1",
"name": "RTDEL",
"type": "input",
"description": "A resistor from this pin to GND programs the turn-on delay of the two gate drive outputs (OUT and AUX) for active-clamp resonant transitions, with the same delay for both transitions per the datasheet tDEL equation."
},
{
"number": "2",
"name": "RTON",
"type": "input",
"description": "A resistor from this pin to GND sets the charge current of the internal timing capacitor, and together with RTOFF sets the switching frequency and maximum duty cycle, with the pin held at approximately 2.5 V internally."
},
{
"number": "3",
"name": "RTOFF",
"type": "input",
"description": "A resistor from this pin to GND sets the discharge current of the internal timing capacitor, and together with RTON sets the switching period and DMAX, with the pin held at approximately 2.5 V internally."
},
{
"number": "4",
"name": "VREF",
"type": "power_in",
"description": "This 5-V reference can supply an external load of up to 5 mA and needs a ceramic bypass to GND (recommended 0.22 µF, minimum 0.022 µF, maximum about 22 µF), with VDD capacitance at least 10 times that on VREF."
},
{
"number": "5",
"name": "SYNC",
"type": "input",
"description": "This unidirectional input synchronizes the internal oscillator, requires a minimum pulse width of about 50 ns, and the synchronizing frequency must be higher than the free-running oscillator frequency."
},
{
"number": "6",
"name": "GND",
"type": "power_in",
"description": "This is the fundamental analog ground reference for the PWM control circuitry and must be connected directly to PGND (pin 11) at the device."
},
{
"number": "7",
"name": "CS",
"type": "input",
"description": "This direct input to the PWM and current-limit comparators reaches the pulse-by-pulse limit at approximately 1.27 V for the UCC2894, and it must be fed through a small RC filter rather than connected directly across the sense resistor."
},
{
"number": "8",
"name": "RSLOPE",
"type": "input",
"description": "A resistor from this pin to GND sets the amplitude of the internal slope-compensation current, which is proportional to the timing-capacitor ramp voltage across RSLOPE."
},
{
"number": "9",
"name": "FB",
"type": "input",
"description": "This input receives the control voltage from an external error amplifier or optocoupler, with a useful range of approximately 1.25 V to 4.5 V and an external pull-up resistor to VREF required."
},
{
"number": "10",
"name": "SS/SD",
"type": "input",
"description": "A capacitor from this pin to GND sets the soft-start time, charged by a current of 0.43 × IRTON to about 5 V, and is discharged by a current equal to IRTON during faults, with a discharge/shutdown threshold of 0.4 V to 0.6 V."
},
{
"number": "11",
"name": "PGND",
"type": "power_in",
"description": "This pin is the dedicated current return for the high-current OUT and AUX drivers and should be kept short and low-impedance, with a low-impedance external connection to GND (pin 6) required."
},
{
"number": "12",
"name": "AUX",
"type": "output",
"description": "This high-current gate drive output drives the auxiliary clamp switch, which for the UCC2894 is an active-high drive for an N-channel device with 2-A source and 2-A sink turn-on/turn-off current."
},
{
"number": "13",
"name": "OUT",
"type": "output",
"description": "This high-current output drives the main N-channel MOSFET with 2-A source and 2-A sink current, and a 10-kΩ resistor to PGND is recommended."
},
{
"number": "14",
"name": "VDD",
"type": "power_in",
"description": "This is the device supply, with a recommended operating range of 8.5 V to 16.0 V (12.0 V nominal), an absolute maximum of 16.5 V at IDD below 10 mA, and at least 1 µF of ceramic capacitance directly from VDD to PGND."
},
{
"number": "15",
"name": "LINEUV",
"type": "input",
"description": "This input enables and disables the converter by monitoring the bulk input against a 1.27 V threshold, with hysteresis set by an internal current source that is programmed through RDEL."
},
{
"number": "16",
"name": "LINEOV",
"type": "input",
"description": "For the UCC2894, this input provides the line overvoltage function against a 1.27 V threshold, with programmable hysteresis set by an internal current source that is programmed through RDEL."
}
],
"provenance": {
"extractor": "extract_pins 0.3",
"factory_chain": {
"factory": "2.0.0",
"extractor": "extract_pins 0.3",
"primary_model": "claude-haiku-5-5",
"primary_mode": "text",
"consensus_model": "claude-sonnet-5-5",
"consensus": "agreed",
"guards": "pin_guards 0.1: passed",
"guard_notes": [
"extractor flagged: The pin is named RTDEL in the pin assignment and terminal functions table but RDEL in the detailed p; The RDEL detailed description refers to AUX as pin 14 and OUT as pin 13, but the pin assignment and ; Pin 16 is LINEOV on the UCC2892/UCC2894 variants but VIN on the UCC2891/UCC2893. The UCC2894PW uses "
],
"pages_sent": 16,
"cost_usd": 0.0946,
"at": "2026-10-31T00:46:07"
},
"datasheet": {
"url": "https://www.ti.com/lit/ds/symlink/ucc2894.pdf",
"pages": 41,
"sha256": "0b123b68deef52c5",
"source_tier": "mfr"
},
"cad": "KiCad official (CC-BY-SA 4.0)",
"pins": {
"total": 16,
"described": 16,
"cites_pages": true,
"refuses_to_fabricate": true
}
},
"viewers": {
"symbol": "viewers/symbol.html",
"footprint": "viewers/footprint.html"
},
"models_3d": [
{
"file": "ucc2894pw.step",
"role": "plain",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
6.4,
5.0,
1.1
],
"zmin_mm": -0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",
"checked": "2026-10-31",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
},
{
"file": "ucc2894pw-etched.step",
"role": "eda",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
6.4,
5.0,
1.1
],
"zmin_mm": -0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "724845134a4d2b8bfcd05fd06e2d04a5e1ec4aa1f1bd24ae380325b89c3943c4",
"checked": "2026-10-31",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
}
],
"package_dims": {
"package_code": "PW (PW0016A, TSSOP-16)",
"source_page": 38,
"D": {
"nom_mm": 5.0,
"range_mm": [
4.9,
5.1
]
},
"E1": {
"nom_mm": 4.4,
"range_mm": [
4.3,
4.5
]
},
"E": {
"nom_mm": 6.4,
"range_mm": [
6.2,
6.6
]
},
"e": {
"nom_mm": 0.65,
"range_mm": [
null,
null
]
},
"A": {
"nom_mm": 1.2,
"range_mm": [
null,
1.2
]
},
"source": "datasheet package drawing, every number found on its page (extract_pins --task dims)",
"model_check": {
"file": "ucc2894pw.step",
"verdict": "PASS",
"reasons": [
"height and body within the datasheet's package drawing"
],
"by": "factory/package_fit.py"
}
}
}
}