main
Ray
Publish 0.1.0
93a4fa3
UCC2894PW
Texas Instruments · DC-DC Controllers · TSSOP-16
UCC2894PW from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RTDEL | input | A resistor from this pin to GND programs the turn-on delay of the two gate drive outputs (OUT and AUX) for active-clamp resonant transitions, with the same delay for both transitions per the datasheet tDEL equation. |
| 2 | RTON | input | A resistor from this pin to GND sets the charge current of the internal timing capacitor, and together with RTOFF sets the switching frequency and maximum duty cycle, with the pin held at approximately 2.5 V internally. |
| 3 | RTOFF | input | A resistor from this pin to GND sets the discharge current of the internal timing capacitor, and together with RTON sets the switching period and DMAX, with the pin held at approximately 2.5 V internally. |
| 4 | VREF | power_in | This 5-V reference can supply an external load of up to 5 mA and needs a ceramic bypass to GND (recommended 0.22 µF, minimum 0.022 µF, maximum about 22 µF), with VDD capacitance at least 10 times that on VREF. |
| 5 | SYNC | input | This unidirectional input synchronizes the internal oscillator, requires a minimum pulse width of about 50 ns, and the synchronizing frequency must be higher than the free-running oscillator frequency. |
| 6 | GND | power_in | This is the fundamental analog ground reference for the PWM control circuitry and must be connected directly to PGND (pin 11) at the device. |
| 7 | CS | input | This direct input to the PWM and current-limit comparators reaches the pulse-by-pulse limit at approximately 1.27 V for the UCC2894, and it must be fed through a small RC filter rather than connected directly across the sense resistor. |
| 8 | RSLOPE | input | A resistor from this pin to GND sets the amplitude of the internal slope-compensation current, which is proportional to the timing-capacitor ramp voltage across RSLOPE. |
| 9 | FB | input | This input receives the control voltage from an external error amplifier or optocoupler, with a useful range of approximately 1.25 V to 4.5 V and an external pull-up resistor to VREF required. |
| 10 | SS/SD | input | A capacitor from this pin to GND sets the soft-start time, charged by a current of 0.43 × IRTON to about 5 V, and is discharged by a current equal to IRTON during faults, with a discharge/shutdown threshold of 0.4 V to 0.6 V. |
| 11 | PGND | power_in | This pin is the dedicated current return for the high-current OUT and AUX drivers and should be kept short and low-impedance, with a low-impedance external connection to GND (pin 6) required. |
| 12 | AUX | output | This high-current gate drive output drives the auxiliary clamp switch, which for the UCC2894 is an active-high drive for an N-channel device with 2-A source and 2-A sink turn-on/turn-off current. |
| 13 | OUT | output | This high-current output drives the main N-channel MOSFET with 2-A source and 2-A sink current, and a 10-kΩ resistor to PGND is recommended. |
| 14 | VDD | power_in | This is the device supply, with a recommended operating range of 8.5 V to 16.0 V (12.0 V nominal), an absolute maximum of 16.5 V at IDD below 10 mA, and at least 1 µF of ceramic capacitance directly from VDD to PGND. |
| 15 | LINEUV | input | This input enables and disables the converter by monitoring the bulk input against a 1.27 V threshold, with hysteresis set by an internal current source that is programmed through RDEL. |
| 16 | LINEOV | input | For the UCC2894, this input provides the line overvoltage function against a 1.27 V threshold, with programmable hysteresis set by an internal current source that is programmed through RDEL. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-16 |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Start-up current | ISTARTUP | 300 | 500 | µA | VDD < VUVLO | 3 | |
| Operating supply current | IDD | 2 | 3 | mA | VFB = 0 V, VCS = 0 V, Outputs not switching | 3 | |
| Start threshold voltage | 12.2 | 12.7 | 13.2 | V | 3 | ||
| Minimum operating voltage after start | 7.6 | 8 | 8.4 | V | 3 | ||
| UVLO hysteresis | 4.4 | 4.7 | 5 | V | 3 | ||
| Line UV and Line OV voltage threshold | VLINEUV | 1.243 | 1.268 | 1.293 | V | 3 | |
| Line UV and Line OV hysteresis current | ILINEHYS | 11.8 | 12.5 | 14.5 | µA | 3 | |
| Soft-start charge current | ISS | -18.5 | -10.5 | µA | RTON = 75 kΩ | 3 | |
| Soft-start discharge current | ISS | 10.5 | 18.5 | µA | RTON = 75 kΩ | 3 | |
| VSS/SD discharge/shutdown threshold voltage | VSS/SD | 0.4 | 0.5 | 0.6 | V | 3 | |
| Reference voltage | VREF | 4.85 | 5 | 5.15 | V | TJ = 25°C | 4 |
| Reference voltage | VREF | 4.75 | 5 | 5.25 | V | 0 A < IREF < 5 mA, over temperature | 4 |
| Short circuit current | ISC | -20 | -11 | -8 | mA | REF = 0 V, TJ = 25°C | 4 |
| Internal slope compensation slope | m | -10 | 10 | % | FB = High; relative to RCS/RSLOPE | 4 | |
| Oscillator frequency | fOSC | 237 | 250 | 263 | kHz | TJ = 25°C | 4 |
| Oscillator frequency total variation | fOSC | 225 | 270 | kHz | Total variation −40 °C < TJ 125°C; 8.5 V < 14.5 V | 4 | |
| SYNC threshold voltage | VSYNCH | 1.6 | 2.3 | 3 | V | 4 | |
| Maximum duty cycle | 66 | 70 | 74 | % | 4 | ||
| PWM offset | 0.43 | 0.5 | 0.61 | V | CS = 0 V | 4 | |
| Current sense level shift voltage | VLVL | 0.4 | 0.5 | 0.6 | V | 4 | |
| Maximum voltage error (clamped) | VERR(max) | 4.8 | 5 | 5.2 | V | 4 | |
| Current sense threshold voltage (UCC2892/UCC2894) | VCS | 1.23 | 1.27 | 1.31 | V | UCC2892/UCC2894 | 4 |
| Rise time | tR | 19 | 28 | ns | CLOAD = 2 nF | 5 | |
| Fall time | tF | 14 | 23 | ns | CLOAD = 2 nF | 5 | |
| Line input voltage | VIN | 18 | 110 | V | 2 | ||
| Supply voltage | VDD | 8.5 | 12 | 16 | V | 2 | |
| Operating junction temperature | TJ | -40 | 105 | °C | 2 | ||
| Reference bypass capacitance | CREF | 0.1 | 1 | µF | 2 | ||
| Line input voltage | VIN | 120 | V | 2 | |||
| Supply voltage | VDD | 16.5 | V | IDD < 10 mA | 2 | ||
| Analog inputs FB, CS, SYNC, LINEOV, LINEUV | -0.3 | 6 | V | Max (VREF + 0.3), not to exceed 6 V | 2 | ||
| Output source current (peak) | IO_SOURCE | 2.5 | A | OUT, AUX | 2 | ||
| Output sink current (peak) | IO_SINK | -2.5 | A | OUT, AUX | 2 | ||
| Operating junction temperature range | TJ | -55 | 150 | °C | 2 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 2 | ||
| ESD rating, human body model | 2000 | V | Human body model (HBM) | 2 | |||
| ESD rating, charged device model | 500 | V | Charged device model (CDM) | 2 | |||
| Lead temperature | Tsol | 300 | °C | 1,6 mm (1/16 inch) from case for 10 seconds | 2 | ||
| Thermal resistance junction-to-case (TSSOP-16 PW) | θjc | 33.6 | 35 | °C/W | 3 | ||
| Thermal resistance junction-to-ambient (TSSOP-16 PW) | θja | 108.4 | 147 | °C/W | 0 LFM | 3 |
CAD (KiCad official)
- Symbol:
UCC2894PW - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
ucc2894pw-etched.step/ucc2894pw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc2894pw.step/ucc2894pw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (41 pp, sha256
0b123b68deef52c5, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# UCC2894PW
**Texas Instruments** · DC-DC Controllers · TSSOP-16
UCC2894PW from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RTDEL | input | A resistor from this pin to GND programs the turn-on delay of the two gate drive outputs (OUT and AUX) for active-clamp resonant transitions, with the same delay for both transitions per the datasheet tDEL equation. |
| 2 | RTON | input | A resistor from this pin to GND sets the charge current of the internal timing capacitor, and together with RTOFF sets the switching frequency and maximum duty cycle, with the pin held at approximately 2.5 V internally. |
| 3 | RTOFF | input | A resistor from this pin to GND sets the discharge current of the internal timing capacitor, and together with RTON sets the switching period and DMAX, with the pin held at approximately 2.5 V internally. |
| 4 | VREF | power_in | This 5-V reference can supply an external load of up to 5 mA and needs a ceramic bypass to GND (recommended 0.22 µF, minimum 0.022 µF, maximum about 22 µF), with VDD capacitance at least 10 times that on VREF. |
| 5 | SYNC | input | This unidirectional input synchronizes the internal oscillator, requires a minimum pulse width of about 50 ns, and the synchronizing frequency must be higher than the free-running oscillator frequency. |
| 6 | GND | power_in | This is the fundamental analog ground reference for the PWM control circuitry and must be connected directly to PGND (pin 11) at the device. |
| 7 | CS | input | This direct input to the PWM and current-limit comparators reaches the pulse-by-pulse limit at approximately 1.27 V for the UCC2894, and it must be fed through a small RC filter rather than connected directly across the sense resistor. |
| 8 | RSLOPE | input | A resistor from this pin to GND sets the amplitude of the internal slope-compensation current, which is proportional to the timing-capacitor ramp voltage across RSLOPE. |
| 9 | FB | input | This input receives the control voltage from an external error amplifier or optocoupler, with a useful range of approximately 1.25 V to 4.5 V and an external pull-up resistor to VREF required. |
| 10 | SS/SD | input | A capacitor from this pin to GND sets the soft-start time, charged by a current of 0.43 × IRTON to about 5 V, and is discharged by a current equal to IRTON during faults, with a discharge/shutdown threshold of 0.4 V to 0.6 V. |
| 11 | PGND | power_in | This pin is the dedicated current return for the high-current OUT and AUX drivers and should be kept short and low-impedance, with a low-impedance external connection to GND (pin 6) required. |
| 12 | AUX | output | This high-current gate drive output drives the auxiliary clamp switch, which for the UCC2894 is an active-high drive for an N-channel device with 2-A source and 2-A sink turn-on/turn-off current. |
| 13 | OUT | output | This high-current output drives the main N-channel MOSFET with 2-A source and 2-A sink current, and a 10-kΩ resistor to PGND is recommended. |
| 14 | VDD | power_in | This is the device supply, with a recommended operating range of 8.5 V to 16.0 V (12.0 V nominal), an absolute maximum of 16.5 V at IDD below 10 mA, and at least 1 µF of ceramic capacitance directly from VDD to PGND. |
| 15 | LINEUV | input | This input enables and disables the converter by monitoring the bulk input against a 1.27 V threshold, with hysteresis set by an internal current source that is programmed through RDEL. |
| 16 | LINEOV | input | For the UCC2894, this input provides the line overvoltage function against a 1.27 V threshold, with programmable hysteresis set by an internal current source that is programmed through RDEL. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-16 |
| Category | Power Supply Chip |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Start-up current | ISTARTUP | 300 | | 500 | µA | VDD < VUVLO | 3 |
| Operating supply current | IDD | 2 | | 3 | mA | VFB = 0 V, VCS = 0 V, Outputs not switching | 3 |
| Start threshold voltage | | 12.2 | 12.7 | 13.2 | V | | 3 |
| Minimum operating voltage after start | | 7.6 | 8 | 8.4 | V | | 3 |
| UVLO hysteresis | | 4.4 | 4.7 | 5 | V | | 3 |
| Line UV and Line OV voltage threshold | VLINEUV | 1.243 | 1.268 | 1.293 | V | | 3 |
| Line UV and Line OV hysteresis current | ILINEHYS | 11.8 | 12.5 | 14.5 | µA | | 3 |
| Soft-start charge current | ISS | -18.5 | | -10.5 | µA | RTON = 75 kΩ | 3 |
| Soft-start discharge current | ISS | 10.5 | | 18.5 | µA | RTON = 75 kΩ | 3 |
| VSS/SD discharge/shutdown threshold voltage | VSS/SD | 0.4 | 0.5 | 0.6 | V | | 3 |
| Reference voltage | VREF | 4.85 | 5 | 5.15 | V | TJ = 25°C | 4 |
| Reference voltage | VREF | 4.75 | 5 | 5.25 | V | 0 A < IREF < 5 mA, over temperature | 4 |
| Short circuit current | ISC | -20 | -11 | -8 | mA | REF = 0 V, TJ = 25°C | 4 |
| Internal slope compensation slope | m | -10 | | 10 | % | FB = High; relative to RCS/RSLOPE | 4 |
| Oscillator frequency | fOSC | 237 | 250 | 263 | kHz | TJ = 25°C | 4 |
| Oscillator frequency total variation | fOSC | 225 | | 270 | kHz | Total variation −40 °C < TJ 125°C; 8.5 V < 14.5 V | 4 |
| SYNC threshold voltage | VSYNCH | 1.6 | 2.3 | 3 | V | | 4 |
| Maximum duty cycle | | 66 | 70 | 74 | % | | 4 |
| PWM offset | | 0.43 | 0.5 | 0.61 | V | CS = 0 V | 4 |
| Current sense level shift voltage | VLVL | 0.4 | 0.5 | 0.6 | V | | 4 |
| Maximum voltage error (clamped) | VERR(max) | 4.8 | 5 | 5.2 | V | | 4 |
| Current sense threshold voltage (UCC2892/UCC2894) | VCS | 1.23 | 1.27 | 1.31 | V | UCC2892/UCC2894 | 4 |
| Rise time | tR | 19 | | 28 | ns | CLOAD = 2 nF | 5 |
| Fall time | tF | 14 | | 23 | ns | CLOAD = 2 nF | 5 |
| Line input voltage | VIN | 18 | | 110 | V | | 2 |
| Supply voltage | VDD | 8.5 | 12 | 16 | V | | 2 |
| Operating junction temperature | TJ | -40 | | 105 | °C | | 2 |
| Reference bypass capacitance | CREF | 0.1 | | 1 | µF | | 2 |
| Line input voltage | VIN | | | 120 | V | | 2 |
| Supply voltage | VDD | | | 16.5 | V | IDD < 10 mA | 2 |
| Analog inputs FB, CS, SYNC, LINEOV, LINEUV | | -0.3 | | 6 | V | Max (VREF + 0.3), not to exceed 6 V | 2 |
| Output source current (peak) | IO_SOURCE | | | 2.5 | A | OUT, AUX | 2 |
| Output sink current (peak) | IO_SINK | -2.5 | | | A | OUT, AUX | 2 |
| Operating junction temperature range | TJ | -55 | | 150 | °C | | 2 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 2 |
| ESD rating, human body model | | | | 2000 | V | Human body model (HBM) | 2 |
| ESD rating, charged device model | | | | 500 | V | Charged device model (CDM) | 2 |
| Lead temperature | Tsol | | | 300 | °C | 1,6 mm (1/16 inch) from case for 10 seconds | 2 |
| Thermal resistance junction-to-case (TSSOP-16 PW) | θjc | 33.6 | | 35 | °C/W | | 3 |
| Thermal resistance junction-to-ambient (TSSOP-16 PW) | θja | 108.4 | | 147 | °C/W | 0 LFM | 3 |
## CAD (KiCad official)
- Symbol: `UCC2894PW`
- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`
- 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files: `ucc2894pw-etched.step` / `ucc2894pw-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2894pw.step` / `ucc2894pw.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc2894.pdf) (41 pp, sha256 `0b123b68deef52c5`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ucc2894pw-datasheet.pdf)