main
Ray
Publish 0.1.0
1d95b3e
UCC28704DBVR-1
Texas Instruments · AC-DC Controllers & Regulators · SOT-23-6
UCC28704DBVR-1 from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NTC/SU | bidirectional | Multi-function pin for an external NTC thermistor (0.95 V shutdown threshold with 105-µA source, pulling low shuts down PWM) and depletion-mode FET high-voltage start-up control; max 100-pF filter capacitance, leave floating if unused. |
| 2 | VDD | power_in | Bias supply input, operating range 8.5 V to 35 V (abs max 38 V), UVLO start/stop 21 V/7.7 V, with a minimum 0.047-µF bypass capacitor. |
| 3 | DRV | output | Gate-drive output for the external high-voltage MOSFET, clamped internally to 10.5 V with a 30-mA typical turn-on current source. |
| 4 | CS | input | Current-sense input connected through series resistor RLC to the ground-referenced sense resistor, with internal threshold of 0.188 V to 0.75 V and up to 30 pF filter capacitance allowed. |
| 5 | GND | power_in | Ground reference for the controller and low-side return for the gate drive output; return decoupling capacitors close to this pin. |
| 6 | VS | power_in | Voltage and timing feedback input from the auxiliary-winding resistor divider, also sets AC-mains run/stop thresholds and line compensation; no filter capacitor allowed. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-6 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply current, run | IRUN | 1.65 | 2.3 | 2.65 | mA | IDRV = 0, run state | 5 |
| Supply current, wait | IWAIT | 40 | 70 | 100 | µA | IDRV = 0, VVDD = 20 V, wait state | 5 |
| Supply current, start | ISTART | 1.5 | 2.5 | µA | IDRV = 0, VVDD = 17 V, start state | 5 | |
| Supply current, fault | IFAULT | 1.7 | 2.2 | 2.8 | mA | IDRV = 0, fault state | 5 |
| VDD turn-on threshold | VVDD(on) | 17.5 | 21 | 23 | V | VVDD low to high | 5 |
| VDD turn-off threshold | VVDD(off) | 7.3 | 7.7 | 8.15 | V | VVDD high to low | 5 |
| Regulating level | VVSR | 4.02 | 4.06 | 4.1 | V | Measured at no-load condition, TJ = 25°C | 5 |
| Negative clamp level | VVSNC | 190 | 250 | 325 | mV | IVS = -300 µA | 5 |
| Input bias current | IVSB | -0.25 | 0 | 0.25 | µA | VVS = 4 V | 5 |
| Max CS threshold voltage | VCST(max) | 720 | 750 | 784 | mV | VVS = 3.70 V | 5 |
| Min CS threshold voltage | VCST(min) | 170 | 187.5 | 210 | mV | VVS = 4.35 V | 5 |
| AM control ratio | KAM | 3.55 | 4 | 4.4 | V/V | VCST(max) / VCST(min) | 5 |
| Constant-current regulating level | VCCR | 345 | 356 | 369 | mV | 5 | |
| Line compensating current ratio | KLC | 23 | 25 | 29 | A/A | IVSLS = -300 µA | 5 |
| Leading-edge blanking time | TCSLEB | 170 | 255 | 340 | ns | DRV output duration, VCS = 1 V | 5 |
| DRV source current | IDRS | 25 | 32 | 38 | mA | VDRV = 5 V, VVDD = 9 V | 6 |
| DRV low-side drive resistance | RDRVLS | 6.5 | 12 | Ω | IDRV = 10 mA | 6 | |
| DRV clamp voltage | VDRCL | 9.5 | 10.6 | 13 | V | VVDD = 35 V | 6 |
| DRV pull-down in start state | RDRVSS | 165 | 205 | 250 | kΩ | 6 | |
| Maximum switching frequency | fSW(max) | 78 | 85 | 94 | kHz | VVS = 3.7 V | 6 |
| Minimum switching frequency | fSW(min) | 0.88 | 1.03 | 1.18 | kHz | VVS = 4.6 V | 6 |
| Zero-crossing timeout delay | tZTO | 1.7 | 2.39 | 3 | µs | 6 | |
| Blanking delay time before CCUV shutdown | tCCUV_BLANK | 90 | 120 | 150 | ms | VVS step from 3.5 V to 2.4 V to DRV stop switching | 6 |
| Over-voltage threshold ratio to VVSR | KOVP | 1.13 | 1.15 | 1.18 | V/V | VOVP/VVSR | 6 |
| CCUV threshold | VCCUV | 2.41 | 2.48 | 2.55 | V | VO = 3.0 V TJ = 25℃, auto restart after fault | 6 |
| Over-current threshold | VOCP | 1.35 | 1.51 | 1.6 | V | At CS input | 6 |
| VS line-sense run current | IVSL(run) | 190 | 220 | 265 | µA | Current out of VS pin, increasing | 6 |
| VS line-sense stop current | IVSL(stop) | 70 | 80 | 100 | µA | Current out of VS pin, decreasing | 6 |
| VS line-sense ratio | KVSL | 2.55 | 2.8 | 2.95 | A/A | IVSL(run) / IVSL(stop) | 6 |
| Thermal shut-down temperature | TJ(stop) | 150 | °C | Internal junction temperature | 6 | ||
| Maximum cable compensation at VS | VCVS(max) | 180 | 220 | 260 | mV | Change in VS regulating level at full-load | 6 |
| NTC shut-down threshold | VNTCTH | 0.9 | 0.95 | 1 | V | VDD UVLO cycle when below this threshold | 6 |
| NTC pull-up current, out of pin | INTC | 90 | 100 | 120 | µA | VNTC = 1.1 V | 6 |
| Bias supply voltage | VVDD | 38 | V | 4 | |||
| VS voltage range | VS | -0.75 | 7 | V | 4 | ||
| CS, NTC voltage range | -0.5 | 5 | V | 4 | |||
| DRV continuous sink current | IDRV | 50 | mA | 4 | |||
| VS peak current | IVS | 1.2 | mA | 1% duty-cycle, when detecting line voltage | 4 | ||
| Operating junction temperature range | TJ | -55 | 150 | °C | 4 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 4 | ||
| Lead temperature | TLEAD | 260 | °C | 0.6 mm from case for 10 seconds | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model, ANSI/ESDA/JEDEC JS-001 | 4 | |
| ESD CDM | V(ESD) | -500 | 500 | V | Charged-device model | 4 | |
| Bias supply operating voltage | VDD | 8.5 | 35 | V | 4 | ||
| VDD bypass capacitor | CDD | 0.047 | µF | 4 | |||
| VS pin sourcing current when detecting line voltage | IVS | 1 | mA | 4 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Junction-to-ambient thermal resistance | θJA | 150 | °C/W | DBV 6 pins | 5 | ||
| Junction-to-case (top) thermal resistance | θJCtop | 55 | °C/W | DBV 6 pins | 5 | ||
| Junction-to-board thermal resistance | θJB | 60 | °C/W | DBV 6 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 3 | °C/W | DBV 6 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 55 | °C/W | DBV 6 pins | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • To improve thermal performance increase the copper area connected to GND pins. | 34 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
UCC28704DBVR-1 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ucc28704dbvr-1-etched.step/ucc28704dbvr-1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc28704dbvr-1.step/ucc28704dbvr-1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (45 pp, sha256
7e0e3c3bf4210268, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# UCC28704DBVR-1
**Texas Instruments** · AC-DC Controllers & Regulators · SOT-23-6
UCC28704DBVR-1 from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NTC/SU | bidirectional | Multi-function pin for an external NTC thermistor (0.95 V shutdown threshold with 105-µA source, pulling low shuts down PWM) and depletion-mode FET high-voltage start-up control; max 100-pF filter capacitance, leave floating if unused. |
| 2 | VDD | power_in | Bias supply input, operating range 8.5 V to 35 V (abs max 38 V), UVLO start/stop 21 V/7.7 V, with a minimum 0.047-µF bypass capacitor. |
| 3 | DRV | output | Gate-drive output for the external high-voltage MOSFET, clamped internally to 10.5 V with a 30-mA typical turn-on current source. |
| 4 | CS | input | Current-sense input connected through series resistor RLC to the ground-referenced sense resistor, with internal threshold of 0.188 V to 0.75 V and up to 30 pF filter capacitance allowed. |
| 5 | GND | power_in | Ground reference for the controller and low-side return for the gate drive output; return decoupling capacitors close to this pin. |
| 6 | VS | power_in | Voltage and timing feedback input from the auxiliary-winding resistor divider, also sets AC-mains run/stop thresholds and line compensation; no filter capacitor allowed. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-6 |
| Category | Power Supply Chip |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply current, run | IRUN | 1.65 | 2.3 | 2.65 | mA | IDRV = 0, run state | 5 |
| Supply current, wait | IWAIT | 40 | 70 | 100 | µA | IDRV = 0, VVDD = 20 V, wait state | 5 |
| Supply current, start | ISTART | | 1.5 | 2.5 | µA | IDRV = 0, VVDD = 17 V, start state | 5 |
| Supply current, fault | IFAULT | 1.7 | 2.2 | 2.8 | mA | IDRV = 0, fault state | 5 |
| VDD turn-on threshold | VVDD(on) | 17.5 | 21 | 23 | V | VVDD low to high | 5 |
| VDD turn-off threshold | VVDD(off) | 7.3 | 7.7 | 8.15 | V | VVDD high to low | 5 |
| Regulating level | VVSR | 4.02 | 4.06 | 4.1 | V | Measured at no-load condition, TJ = 25°C | 5 |
| Negative clamp level | VVSNC | 190 | 250 | 325 | mV | IVS = -300 µA | 5 |
| Input bias current | IVSB | -0.25 | 0 | 0.25 | µA | VVS = 4 V | 5 |
| Max CS threshold voltage | VCST(max) | 720 | 750 | 784 | mV | VVS = 3.70 V | 5 |
| Min CS threshold voltage | VCST(min) | 170 | 187.5 | 210 | mV | VVS = 4.35 V | 5 |
| AM control ratio | KAM | 3.55 | 4 | 4.4 | V/V | VCST(max) / VCST(min) | 5 |
| Constant-current regulating level | VCCR | 345 | 356 | 369 | mV | | 5 |
| Line compensating current ratio | KLC | 23 | 25 | 29 | A/A | IVSLS = -300 µA | 5 |
| Leading-edge blanking time | TCSLEB | 170 | 255 | 340 | ns | DRV output duration, VCS = 1 V | 5 |
| DRV source current | IDRS | 25 | 32 | 38 | mA | VDRV = 5 V, VVDD = 9 V | 6 |
| DRV low-side drive resistance | RDRVLS | | 6.5 | 12 | Ω | IDRV = 10 mA | 6 |
| DRV clamp voltage | VDRCL | 9.5 | 10.6 | 13 | V | VVDD = 35 V | 6 |
| DRV pull-down in start state | RDRVSS | 165 | 205 | 250 | kΩ | | 6 |
| Maximum switching frequency | fSW(max) | 78 | 85 | 94 | kHz | VVS = 3.7 V | 6 |
| Minimum switching frequency | fSW(min) | 0.88 | 1.03 | 1.18 | kHz | VVS = 4.6 V | 6 |
| Zero-crossing timeout delay | tZTO | 1.7 | 2.39 | 3 | µs | | 6 |
| Blanking delay time before CCUV shutdown | tCCUV_BLANK | 90 | 120 | 150 | ms | VVS step from 3.5 V to 2.4 V to DRV stop switching | 6 |
| Over-voltage threshold ratio to VVSR | KOVP | 1.13 | 1.15 | 1.18 | V/V | VOVP/VVSR | 6 |
| CCUV threshold | VCCUV | 2.41 | 2.48 | 2.55 | V | VO = 3.0 V TJ = 25℃, auto restart after fault | 6 |
| Over-current threshold | VOCP | 1.35 | 1.51 | 1.6 | V | At CS input | 6 |
| VS line-sense run current | IVSL(run) | 190 | 220 | 265 | µA | Current out of VS pin, increasing | 6 |
| VS line-sense stop current | IVSL(stop) | 70 | 80 | 100 | µA | Current out of VS pin, decreasing | 6 |
| VS line-sense ratio | KVSL | 2.55 | 2.8 | 2.95 | A/A | IVSL(run) / IVSL(stop) | 6 |
| Thermal shut-down temperature | TJ(stop) | | 150 | | °C | Internal junction temperature | 6 |
| Maximum cable compensation at VS | VCVS(max) | 180 | 220 | 260 | mV | Change in VS regulating level at full-load | 6 |
| NTC shut-down threshold | VNTCTH | 0.9 | 0.95 | 1 | V | VDD UVLO cycle when below this threshold | 6 |
| NTC pull-up current, out of pin | INTC | 90 | 100 | 120 | µA | VNTC = 1.1 V | 6 |
| Bias supply voltage | VVDD | | | 38 | V | | 4 |
| VS voltage range | VS | -0.75 | | 7 | V | | 4 |
| CS, NTC voltage range | | -0.5 | | 5 | V | | 4 |
| DRV continuous sink current | IDRV | | | 50 | mA | | 4 |
| VS peak current | IVS | | | 1.2 | mA | 1% duty-cycle, when detecting line voltage | 4 |
| Operating junction temperature range | TJ | -55 | | 150 | °C | | 4 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 4 |
| Lead temperature | TLEAD | | | 260 | °C | 0.6 mm from case for 10 seconds | 4 |
| ESD HBM | V(ESD) | -2000 | | 2000 | V | Human-body model, ANSI/ESDA/JEDEC JS-001 | 4 |
| ESD CDM | V(ESD) | -500 | | 500 | V | Charged-device model | 4 |
| Bias supply operating voltage | VDD | 8.5 | | 35 | V | | 4 |
| VDD bypass capacitor | CDD | 0.047 | | | µF | | 4 |
| VS pin sourcing current when detecting line voltage | IVS | | | 1 | mA | | 4 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Junction-to-ambient thermal resistance | θJA | | 150 | | °C/W | DBV 6 pins | 5 |
| Junction-to-case (top) thermal resistance | θJCtop | | 55 | | °C/W | DBV 6 pins | 5 |
| Junction-to-board thermal resistance | θJB | | 60 | | °C/W | DBV 6 pins | 5 |
| Junction-to-top characterization parameter | ψJT | | 3 | | °C/W | DBV 6 pins | 5 |
| Junction-to-board characterization parameter | ψJB | | 55 | | °C/W | DBV 6 pins | 5 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | • To improve thermal performance increase the copper area connected to GND pins. | 34 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `UCC28704DBVR-1`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `ucc28704dbvr-1-etched.step` / `ucc28704dbvr-1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc28704dbvr-1.step` / `ucc28704dbvr-1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc28704.pdf) (45 pp, sha256 `7e0e3c3bf4210268`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/ucc28704dbvr-1-datasheet.pdf)