main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ucc28704dbvr-1: viewers rendered from the public page · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
ucc28704dbvr-1-etched.glb ucc28704dbvr-1: factory component page (tier=mfr) · Ray
ucc28704dbvr-1-etched.step ucc28704dbvr-1: factory component page (tier=mfr) · Ray
ucc28704dbvr-1-hero.glb ucc28704dbvr-1: hero GLB from the etched model (keeps the MPN mark) · Ray
ucc28704dbvr-1-hero.overlay.json ucc28704dbvr-1: hero GLB from the etched model (keeps the MPN mark) · Ray
ucc28704dbvr-1.glb Publish 0.1.0 · Ray
ucc28704dbvr-1.kicad_mod Publish 0.1.0 · Ray
ucc28704dbvr-1.kicad_sym Publish 0.1.0 · Ray
ucc28704dbvr-1.lbr Publish 0.1.0 · Ray
ucc28704dbvr-1.step Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 6 pins · Ray

UCC28704DBVR-1

Texas Instruments · AC-DC Controllers & Regulators · SOT-23-6

UCC28704DBVR-1 from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 NTC/SU bidirectional Multi-function pin for an external NTC thermistor (0.95 V shutdown threshold with 105-µA source, pulling low shuts down PWM) and depletion-mode FET high-voltage start-up control; max 100-pF filter capacitance, leave floating if unused.
2 VDD power_in Bias supply input, operating range 8.5 V to 35 V (abs max 38 V), UVLO start/stop 21 V/7.7 V, with a minimum 0.047-µF bypass capacitor.
3 DRV output Gate-drive output for the external high-voltage MOSFET, clamped internally to 10.5 V with a 30-mA typical turn-on current source.
4 CS input Current-sense input connected through series resistor RLC to the ground-referenced sense resistor, with internal threshold of 0.188 V to 0.75 V and up to 30 pF filter capacitance allowed.
5 GND power_in Ground reference for the controller and low-side return for the gate drive output; return decoupling capacitors close to this pin.
6 VS power_in Voltage and timing feedback input from the auxiliary-winding resistor divider, also sets AC-mains run/stop thresholds and line compensation; no filter capacitor allowed.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOT-23-6
Category Power Supply Chip
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply current, run IRUN 1.65 2.3 2.65 mA IDRV = 0, run state 5
Supply current, wait IWAIT 40 70 100 µA IDRV = 0, VVDD = 20 V, wait state 5
Supply current, start ISTART 1.5 2.5 µA IDRV = 0, VVDD = 17 V, start state 5
Supply current, fault IFAULT 1.7 2.2 2.8 mA IDRV = 0, fault state 5
VDD turn-on threshold VVDD(on) 17.5 21 23 V VVDD low to high 5
VDD turn-off threshold VVDD(off) 7.3 7.7 8.15 V VVDD high to low 5
Regulating level VVSR 4.02 4.06 4.1 V Measured at no-load condition, TJ = 25°C 5
Negative clamp level VVSNC 190 250 325 mV IVS = -300 µA 5
Input bias current IVSB -0.25 0 0.25 µA VVS = 4 V 5
Max CS threshold voltage VCST(max) 720 750 784 mV VVS = 3.70 V 5
Min CS threshold voltage VCST(min) 170 187.5 210 mV VVS = 4.35 V 5
AM control ratio KAM 3.55 4 4.4 V/V VCST(max) / VCST(min) 5
Constant-current regulating level VCCR 345 356 369 mV 5
Line compensating current ratio KLC 23 25 29 A/A IVSLS = -300 µA 5
Leading-edge blanking time TCSLEB 170 255 340 ns DRV output duration, VCS = 1 V 5
DRV source current IDRS 25 32 38 mA VDRV = 5 V, VVDD = 9 V 6
DRV low-side drive resistance RDRVLS 6.5 12 Ω IDRV = 10 mA 6
DRV clamp voltage VDRCL 9.5 10.6 13 V VVDD = 35 V 6
DRV pull-down in start state RDRVSS 165 205 250 kΩ 6
Maximum switching frequency fSW(max) 78 85 94 kHz VVS = 3.7 V 6
Minimum switching frequency fSW(min) 0.88 1.03 1.18 kHz VVS = 4.6 V 6
Zero-crossing timeout delay tZTO 1.7 2.39 3 µs 6
Blanking delay time before CCUV shutdown tCCUV_BLANK 90 120 150 ms VVS step from 3.5 V to 2.4 V to DRV stop switching 6
Over-voltage threshold ratio to VVSR KOVP 1.13 1.15 1.18 V/V VOVP/VVSR 6
CCUV threshold VCCUV 2.41 2.48 2.55 V VO = 3.0 V TJ = 25℃, auto restart after fault 6
Over-current threshold VOCP 1.35 1.51 1.6 V At CS input 6
VS line-sense run current IVSL(run) 190 220 265 µA Current out of VS pin, increasing 6
VS line-sense stop current IVSL(stop) 70 80 100 µA Current out of VS pin, decreasing 6
VS line-sense ratio KVSL 2.55 2.8 2.95 A/A IVSL(run) / IVSL(stop) 6
Thermal shut-down temperature TJ(stop) 150 °C Internal junction temperature 6
Maximum cable compensation at VS VCVS(max) 180 220 260 mV Change in VS regulating level at full-load 6
NTC shut-down threshold VNTCTH 0.9 0.95 1 V VDD UVLO cycle when below this threshold 6
NTC pull-up current, out of pin INTC 90 100 120 µA VNTC = 1.1 V 6
Bias supply voltage VVDD 38 V 4
VS voltage range VS -0.75 7 V 4
CS, NTC voltage range -0.5 5 V 4
DRV continuous sink current IDRV 50 mA 4
VS peak current IVS 1.2 mA 1% duty-cycle, when detecting line voltage 4
Operating junction temperature range TJ -55 150 °C 4
Storage temperature TSTG -65 150 °C 4
Lead temperature TLEAD 260 °C 0.6 mm from case for 10 seconds 4
ESD HBM V(ESD) -2000 2000 V Human-body model, ANSI/ESDA/JEDEC JS-001 4
ESD CDM V(ESD) -500 500 V Charged-device model 4
Bias supply operating voltage VDD 8.5 35 V 4
VDD bypass capacitor CDD 0.047 µF 4
VS pin sourcing current when detecting line voltage IVS 1 mA 4
Operating junction temperature TJ -40 125 °C 4
Junction-to-ambient thermal resistance θJA 150 °C/W DBV 6 pins 5
Junction-to-case (top) thermal resistance θJCtop 55 °C/W DBV 6 pins 5
Junction-to-board thermal resistance θJB 60 °C/W DBV 6 pins 5
Junction-to-top characterization parameter ψJT 3 °C/W DBV 6 pins 5
Junction-to-board characterization parameter ψJB 55 °C/W DBV 6 pins 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper • To improve thermal performance increase the copper area connected to GND pins. 34

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: UCC28704DBVR-1
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ucc28704dbvr-1-etched.step / ucc28704dbvr-1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc28704dbvr-1.step / ucc28704dbvr-1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (45 pp, sha256 7e0e3c3bf4210268, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF