3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownUCC28513N
Texas Instruments · AC-DC Controllers & Regulators · PDIP-20
UCC28513N from Texas Instruments, in a PDIP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VAOUT | bidirectional | Output of the PFC transconductance voltage amplifier, which operates between GND and 5.5 V maximum, sets the multiplier output current to zero below 1 V, and turns off the PFC gate drive when it falls below 0.33 V. |
| 2 | RT | input | A resistor from RT to GND programs the oscillator frequency measured at CT_BUFF over a recommended 45 kΩ to 500 kΩ range (600 kHz to 65 kHz), and the pin is nominally 3 V dc with no capacitor allowed. |
| 3 | VSENSE | input | Inverting input to the PFC transconductance voltage amplifier (the PFC feedback point), also connected to the OVP, ENABLE and UVLO2 comparators. |
| 4 | D_MAX | input | Positive input that programs the PWM maximum duty cycle at GT2, linear between 0.09 and 0.90 duty ratio, and a voltage below 0.7 V sets DMAX to 0. |
| 5 | CT_BUFF | output | Internally buffered 4-V amplitude PWM oscillator ramp output for slope compensation through a resistor to ISENSE2, and the internal buffer can drive a typical 500 µA resistive load. |
| 6 | GND | power_in | Signal ground for the IC to which all measured voltages are referenced, and PWRGND must be externally connected to it. |
| 7 | VERR | input | Feedback error voltage input for the PWM stage that is clamped to a maximum of 3 V, can demand 100% duty cycle at GT2, and has a typical 10 µA pull-up current. |
| 8 | ISENSE2 | input | Input for PWM stage current sense and peak current limit, with the peak limit threshold set to 1.3 V for peak current mode control. |
| 9 | VCC | power_in | Positive supply that should be connected to a stable source of at least 20 mA between 12 V and 17 V for normal operation, bypassed to GND with a 0.1 µF or larger ceramic capacitor. |
| 10 | GT2 | output | PWM stage MOSFET gate driver output, a 2-A peak source and 3-A peak sink totem pole driver. |
| 11 | PWRGND | power_in | Ground for the GT1 and GT2 output drivers, which should be tied to GND externally via a single Kelvin connection. |
| 12 | GT1 | output | PFC stage MOSFET gate driver output, a 2-A peak source and 3-A peak sink totem pole driver that is disabled unless VCC is outside the UVLO region and VREF is on. |
| 13 | SS2 | input | Soft-start pin for the PWM stage where an internal 10.5-µA source charges the external capacitor to 3 V, and SS2 quickly discharges to ground on a disable command or UVLO2 dropout. |
| 14 | PKLMT | input | Peak current limit input for the PFC stage with a 0 V threshold, using a resistor divider from VREF to the non-grounded side of the PFC current sense resistor. |
| 15 | CAOUT | output | Output of the PFC wide-bandwidth current amplifier that commands the PFC PWM comparator duty cycle, with current loop compensation connected between CAOUT and MOUT. |
| 16 | ISENSE1 | input | Non-inverting input of the PFC stage current amplifier, connected through a resistor to the grounded side of the PFC current sense resistor, with a value equal to the MOUT resistor. |
| 17 | MOUT | bidirectional | High-impedance multiplier current output and current amplifier input for the PFC stage, where a resistor to the non-grounded end of the PFC current sense resistor sets the power range. |
| 18 | IAC | input | Multiplier input that senses the rectified AC line voltage through a resistor, with a recommended maximum IAC current of 500 µA. |
| 19 | VFF | input | Voltage feedforward pin that sources an IAC/2 current through an external single-pole R/C filter to GND, and should be set to 1.4 V at low line. |
| 20 | VREF | power_out | Precision 7.5-V reference output that can deliver over 10 mA, is current limited to 25 mA, and should be bypassed to GND with a 0.1 µF to 10 µF ceramic capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-20 |
| Category | Power Supply Chip |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC, idle | VCC | 20 | V | Idle | 3 | ||
| Supply voltage VCC, operating | VCC | 18 | V | Operating | 3 | ||
| Gate drive current (GT1, GT2), continuous | 0.4 | A | Continuous | 3 | |||
| Gate drive current (GT1, GT2), pulsed sourcing | -2.5 | A | Pulsed, sourcing | 3 | |||
| Gate drive current (GT1, GT2), pulsed sinking | 3.5 | A | Pulsed, sinking | 3 | |||
| Maximum GT1, GT2 voltage | -0.5 | V | Upper limit printed as VCC + 0.3 V | 3 | |||
| Input voltage VSENSE | 0 | 11 | V | 3 | |||
| Input voltage D_MAX, SS2, CAOUT, ISENSE1, MOUT, VFF | -0.5 | V | Upper limit printed as VREF + 0.3 V | 3 | |||
| Input voltage VAOUT, CT_BUFF, ISENSE2, PKLMT | -0.5 | 6 | V | 3 | |||
| Pin current RT | -0.5 | mA | 3 | ||||
| Pin current VFF | -5 | mA | 3 | ||||
| Pin current CT_BUFF | 1 | mA | 3 | ||||
| Pin current VAOUT, VERR, ISENSE2, SS2, CAOUT, IAC | 10 | mA | Sign not printed in source | 3 | |||
| Maximum pin capacitance ISENSE2 | 220 | pF | 3 | ||||
| Operating junction temperature range | TJ | -55 | 150 | °C | 3 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 3 | ||
| Power dissipation, PDIP (N) package | 1 | W | PDIP (N) package | 3 | |||
| ESD human body model | 2.5 | kV | Human body model | 3 | |||
| ESD charged device model (CDM) | 0.5 | kV | CDM | 3 | |||
| Operating free-air temperature range | TA | -40 | 105 | °C | Footnote: all devices rated from −40°C to +105°C | 3 | |
| Supply current, off | 100 | 150 | µA | VCC turn-on threshold −300 mV | 4 | ||
| Supply current, on | 4 | 6 | mA | No load on GT1 or GT2 | 4 | ||
| VCC turn-on threshold (UCC28513 option) | 9.7 | 10.2 | 10.8 | V | 4 | ||
| VCC turn-off threshold | 9.1 | 9.7 | 10.6 | V | UCC2851X | 4 | |
| UVLO hysteresis (UCC28513 option) | 0.3 | 0.5 | 0.8 | V | 4 | ||
| Overvoltage reference window (VREF +) | 0.44 | 0.49 | 0.54 | V | 4 | ||
| Overvoltage hysteresis | 300 | 500 | 600 | mV | 4 | ||
| Voltage amplifier open loop gain | 50 | 60 | dB | 2 V ≤ VAOUT ≤ 4 V | 4 | ||
| Voltage amplifier high-level output voltage | 5.3 | 5.5 | 5.6 | V | ILOAD = -150 µA | 4 | |
| Voltage amplifier low-level output voltage | 0 | 0.05 | 0.15 | V | ILOAD = 150 µA | 4 | |
| Voltage amplifier gM conductance | 70 | 100 | 130 | µS | IVAOUT = −20 µA to 20 µA | 4 | |
| Voltage amplifier maximum source current | -1 | -3.5 | mA | 4 | |||
| Voltage amplifier maximum sink current | 1 | 3.5 | mA | 4 | |||
| Current amplifier input offset voltage | -5 | 0 | 5 | mV | VCM = 0 V, VCAOUT = 3 V | 5 | |
| Current amplifier input bias current | -50 | -100 | nA | VCM = 0 V, VCAOUT = 3 V | 5 | ||
| Reference input voltage at 25°C | 7.39 | 7.5 | 7.61 | V | 25°C | 5 | |
| Reference input voltage over temperature | 7.35 | 7.5 | 7.65 | V | Over temperature | 5 | |
| Oscillator fPWM initial accuracy | fPWM | 170 | 200 | 230 | kHz | TA = 25°C | 5 |
| Oscillator frequency total variation | 160 | 240 | kHz | Line, Temp | 5 | ||
| dc-to-dc ramp peak voltage | 4.5 | 5 | 5.5 | V | 5 | ||
| PFC ramp peak voltage | 4.5 | 5 | 5.5 | V | 5 | ||
| Reference short circuit current | -20 | -25 | -50 | mA | VREF = 0 V | 5 | |
| PKLMT reference voltage | -20 | 0 | 20 | mV | 5 | ||
| PKLMT propagation delay, PKLMT to GT1 | 150 | 300 | 500 | ns | 5 | ||
| IMOUT low-line high-power output current | IMOUT | -245 | -290 | -330 | µA | IAC = 150 µA, VFF = 1.4 V, VAOUT = 5 V | 5 |
| Power limit (IMOUT × VFF) | -343 | -406 | -462 | µW | IAC = 150 µA, VFF = 1.4 V, VAOUT = 5 V | 5 | |
| Zero power comparator threshold | 0.2 | 0.33 | 0.5 | V | Measured on VAOUT, falling edge | 6 | |
| Zero power comparator hysteresis | 40 | 90 | 140 | mV | Measured on VAOUT, rising edge | 6 | |
| GT1 output rise time | 16 | 25 | ns | CLOAD = 1 nF, RLOAD = 10 Ω | 6 | ||
| GT1 output fall time | 7 | 15 | ns | CLOAD = 1 nF, RLOAD = 10 Ω | 6 | ||
| Maximum duty cycle (PFC GT1) | 93 | 95 | 100 | % | 6 | ||
| PWM turn-on reference | 6.3 | 6.75 | 7.3 | V | UCC2851X | 6 | |
| PWM UVLO2 hysteresis (UCC28513 option) | 2.56 | 3.2 | 3.84 | V | 6 | ||
| SS2 charge current | -14 | -10.5 | -7 | µA | VSENSE = 7.5 V, SS2 = 0 V | 6 | |
| Maximum duty cycle clamp (D_MAX) | 70 | 75 | 80 | % | D_MAX = 4.15 V | 6 | |
| Current sense comparator offset voltage | 1.35 | 1.5 | 1.65 | V | ISENSE2 = 0 V, measured on VERR | 6 | |
| Peak current comparator threshold voltage | 1.15 | 1.3 | 1.45 | V | 7 | ||
| PWM overcurrent input bias current | 50 | nA | Ensured by design | 7 | |||
| GT2 output rise time | 16 | 25 | ns | CLOAD = 1 nF, RLOAD = 10 Ω | 7 | ||
| GT2 output fall time | 7 | 15 | ns | CLOAD = 1 nF, RLOAD = 10 Ω | 7 |
CAD (KiCad official)
- Symbol:
UCC28513N - Footprint:
Package_DIP:DIP-20_W7.62mm - 3D model: PDIP-20 (KiCad packages3D, STEP)
- 3D model files:
ucc28513n-etched.step/ucc28513n-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc28513n.step/ucc28513n.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
0f7a7f654ed0116b, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).