3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownUCC28251RGPR
Texas Instruments · AC-DC Controllers And Regulators · QFN-20-EP(4x4)
UCC28251RGPR from Texas Instruments, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REF/EA+ | input | Non-inverting input of the internal error amplifier, with a common-mode input range of 0 V to 3.0 V. |
| 2 | FB/EA- | input | Inverting input of the internal error amplifier, with a maximum allowed voltage of 3.7 V. |
| 3 | COMP | bidirectional | Error amplifier output and PWM comparator input; the PWM comparator's maximum input common-mode voltage is 2.8 V, and the RAMP peak is suggested to stay below 2.3 V. |
| 4 | GND | power_in | Ground reference for the whole device; all signal returns should be tied to this pin. |
| 5 | VDD | power_in | Bias supply input with a recommended range of 4.7 V to 17 V (12 V nominal), an absolute maximum of 20 V, and a minimum 1-µF bypass capacitor. |
| 6 | SRB | output | Synchronous rectifier output with 0.2-A sink/source capability; an external gate driver is required. |
| 7 | SRA | output | Synchronous rectifier output with 0.2-A sink/source capability; an external gate driver is required. |
| 8 | OUTB | output | Primary switching output with 0.2-A sink/source capability; an external gate driver is required. |
| 9 | OUTA | output | Primary switching output with 0.2-A sink/source capability; an external gate driver is required. |
| 10 | HICC | input | An external capacitor from this pin to GND sets the cycle-by-cycle current-limit shutdown delay and the hiccup restart time, which is about 100 times the shutdown delay. |
| 11 | PS | input | Sets the primary-off to synchronous-rectifier-on dead time through an external resistor (5 kΩ to 250 kΩ); tying it to VREF gives zero dead time. |
| 12 | SP | input | Sets the synchronous-rectifier-off to primary-on dead time through an external resistor (5 kΩ to 250 kΩ); tying it to VREF gives zero dead time. |
| 13 | SS | bidirectional | Soft-start programming pin charged by a 27-µA internal current source through an external capacitor. |
| 14 | VSENSE | input | Output voltage sense input for pre-bias control, with an input voltage range of 0 V to 3.3 V. |
| 15 | RT | input | Oscillator frequency set by an external resistor (12.5 kΩ to 200 kΩ), or an external synchronization clock input. |
| 16 | RAMP/CS | input | Multifunction pin used as the PWM ramp input for voltage mode or the current-sense input for current mode, with a recommended voltage range of 0 V to 2.3 V. |
| 17 | ILIM | input | Cycle-by-cycle over-current sense input with a current-limit threshold of 0.497 V to 0.513 V (0.505 V typical). |
| 18 | EN | input | Device enable/disable input with a trigger threshold of 1.5 V to 2.25 V (2.0 V typical). |
| 19 | OVP/OTP | input | Over-voltage and over-temperature fault input; a voltage above 0.7 V shuts down the outputs, followed by hiccup restart, with 8.5-µA internal hysteresis current. |
| 20 | VREF | power_out | 3.3-V reference output that requires a 0.47-µF to 2.2-µF bypass capacitor and is internally current limited to 25 mA (typical). |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-20-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage range, VDD | VDD | 4.7 | 12 | 17 | V | 5 | |
| VREF bypass capacitor | 0.47 | 2.2 | µF | 5 | |||
| Error amplifier input common mode range (REF/EA+, FB/EA-) | 0 | 3 | V | 5 | |||
| VSENSE input voltage range | 0 | 3.3 | V | 5 | |||
| RT resistor range | 12.5 | 200 | kΩ | 5 | |||
| PS, SP resistor range | 5 | 250 | kΩ | 5 | |||
| RAMP/CS voltage range | 0 | 2.3 | V | 5 | |||
| Operating junction temperature range | TJ | -40 | 150 | °C | 5 | ||
| Input supply voltage VDD | VDD | -0.3 | 20 | V | 5 | ||
| Output voltage on OUTA, OUTB, SRA and SRB (printed max VDD + 0.3 V) | -0.3 | V | 5 | ||||
| COMP voltage (printed max VREF + 0.3 V) | -0.3 | V | 5 | ||||
| Input voltages on SS and EN | -0.3 | 5.5 | V | 5 | |||
| Input voltages on RT, PS, SP, ILIM, OVP, HICC, VSENSE, EA+ and EA- | -0.3 | 3.6 | V | 5 | |||
| Input voltage on RAMP/CS | -0.3 | 4.3 | V | 5 | |||
| Output voltage on VREF | -0.3 | 3.6 | V | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Startup current | IDD(off) | 150 | 275 | µA | VDD = 3.6 V | 6 | |
| Operating supply current | IDD | 1.2 | 2 | 2.5 | mA | 100-pF capacitor on OUTA, OUTB, SRA and SRB | 6 |
| Standby current | IDD(dis) | 250 | 425 | 600 | µA | EN = 0 V | 6 |
| Start threshold (UVLO rising) | VUVLOR | 4 | 4.3 | 4.65 | V | 6 | |
| Minimum operating voltage after start (UVLO falling) | VUVLOF | 3.8 | 4.1 | 4.4 | V | 6 | |
| UVLO hysteresis | 0.15 | 0.2 | 0.25 | V | 6 | ||
| Soft-start charge current | ISS | 26 | 28 | 30 | µA | VSS = 0 V | 6 |
| Soft-start clamp voltage | VSS(max) | 3.3 | 3.6 | 4 | V | 6 | |
| Enable trigger threshold | 1.5 | 2 | 2.25 | V | 6 | ||
| High-level COMP voltage | 2.8 | 3 | V | 6 | |||
| Low-level COMP voltage | 0.3 | 0.4 | V | 6 | |||
| Error amplifier input offset | -16.2 | 18 | mV | 6 | |||
| Error amplifier open loop gain | 70 | 100 | dB | 6 | |||
| COMP sink current | ICOMP(snk) | 3 | 6.5 | 9 | mA | 6 | |
| COMP source current | ICOMP(src) | 2 | 4.5 | 8 | mA | 6 | |
| Nominal switching frequency at OUTA or OUTB set by RT | FSW(nom) | 90 | 98 | 106 | kHz | RT/SYNC = 75 kΩ, RSP = 20 kΩ | 7 |
| Minimum switching frequency set by external sync frequency | FSW(min_sync) | 42 | kHz | fRT/SYNC = 50 kHz | 7 | ||
| Maximum switching frequency set by external sync frequency | FSW(max_sync) | 945 | kHz | fRT/SYNC = 2.5 MHz | 7 | ||
| VREF output voltage | VVREF | 3.17 | 3.25 | 3.33 | V | VDD = from 7 V to 17 V, IVREF = 2 mA | 7 |
| VREF output voltage (load) | VVREF | 3.17 | 3.25 | 3.33 | V | 0 < IREF < 10 mA | 7 |
| VREF short circuit current | 12 | 25 | 40 | mA | VREF = 3 V, TJ = 25 °C | 7 | |
| ILIM cycle-by-cycle threshold | VILIM | 0.497 | 0.505 | 0.513 | V | 7 | |
| Propagation delay from ILIM to OUTA and OUTB (RGP package) | TPDILIM | 15 | 25 | 36 | ns | Exclude leading edge blanking (UCC28251RGP) | 7 |
| Leading edge blanking | TBLANK | 35 | 60 | 90 | ns | 7 | |
| Current limit shutdown delay timing program current | 55 | 75 | 95 | µA | Measured at HICC pin | 7 | |
| Hiccup timing program current | 2 | 2.7 | 3.5 | µA | Measured at HICC pin | 7 | |
| Current limit shutdown delay timer threshold at HICC | VHICC_SD | 0.55 | 0.6 | 0.65 | V | 7 | |
| HICC pull-up threshold | VHICC_PU | 2.25 | 2.4 | 2.5 | V | 7 | |
| Hiccup restart threshold | VHICC_RST | 0.25 | 0.3 | 0.35 | V | 7 | |
| RAMP/CS clamp voltage | VCS(max) | 3.5 | 4 | 4.5 | V | 10-V ramp charging voltage source with 40-kΩ current limiting resistor | 7 |
| OVP/OTP internal reference | VOVP | 0.66 | 0.7 | 0.74 | V | 8 | |
| OVP/OTP internal current | IOVP | 6 | 8.5 | 11 | µA | 8 | |
| Primary output source resistance | RSRC | 12 | 20 | 35 | Ω | IOUT = 20 mA | 8 |
| Primary output sink resistance | RSNK | 4 | 12 | 30 | Ω | IOUT = 20 mA | 8 |
| Synchronous rectifier output source resistance (VDD = 12 V) | RSRC | 12 | 20 | 35 | Ω | IOUT = 20 mA, VDD = 12 V | 8 |
| Synchronous rectifier output source resistance (VDD = 5 V) | RSRC | 15 | 25 | 45 | Ω | IOUT = 20 mA, VDD = 5 V | 8 |
| Synchronous rectifier output sink resistance | RSNK | 4 | 12 | 30 | Ω | IOUT = 20 mA, VDD = 12 V | 8 |
| Primary off to secondary on dead time (PS = VREF) | TDPS | -5 | 0 | 7.5 | ns | PS = VREF | 8 |
| Primary off to secondary on dead time (PS = 27 kΩ) | TDPS | 25 | 38 | 48 | ns | PS = 27 kΩ | 8 |
| Secondary off to primary on dead time (SP = VREF) | TDSP | -5 | 0 | 7.5 | ns | SP = VREF | 8 |
| Secondary off to primary on dead time (SP = 20 kΩ) | TDSP | 33 | 43 | 55 | ns | SP = 20 kΩ | 8 |
| Junction-to-ambient thermal resistance (RGP, with hot spot) | RθJA | 126 | °C/W | with hot spot | 6 | ||
| Junction-to-ambient thermal resistance (RGP, without hot spot) | RθJA | 104 | °C/W | without hot spot | 6 | ||
| Junction-to-case (bottom) thermal resistance (RGP) | RθJC(bot) | 0.8 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
UCC28251RGPR - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
ucc28251rgpr-etched.step/ucc28251rgpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc28251rgpr.step/ucc28251rgpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (58 pp, sha256
67008ba993940d0e, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).