main
Ray
ucc2804qdrq1: one-pass backfill (citation: stored_copy)
8d47c4d
UCC2804QDRQ1
Texas Instruments · AC-DC Controllers & Regulators · SOIC-8
UCC2804QDRQ1 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | output | Output of the low-impedance 2-MHz error amplifier and input of the PWM comparator; it can source and sink current, is internally current-limited so forcing it to GND commands zero duty cycle, and carries the soft-start clamp. |
| 2 | FB | input | Inverting input of the error amplifier; keep lead length and stray capacitance as small as possible for best stability. |
| 3 | CS | input | Input to the PWM and overcurrent comparators with 100-ns leading-edge blanking after the OUT rising edge; exceeding the overcurrent threshold causes a soft-start cycle. |
| 4 | RC | input | Oscillator timing pin: resistor from REF to RC (10 kΩ to 200 kΩ recommended) and capacitor from RC to GND (100 pF to 1000 pF) set the frequency. |
| 5 | GND | power_in | Reference ground and power ground for all functions on the part. |
| 6 | OUT | output | High-current gate driver output capable of peak currents exceeding ±750 mA (±1 A absolute maximum), actively held low when VCC is below the UVLO threshold. |
| 7 | VCC | power_in | Power input, fed through a current-limiting resistor with 12 V absolute maximum from a low-impedance source and 30 mA maximum current; bypass with at least 1 µF in parallel with 0.1 µF ceramic to GND. |
| 8 | REF | power_out | Voltage reference output (5 V, or 4 V for UCC2803/05) bypassed with at least 0.1 µF ceramic to GND; extra bypassing is needed for loads above 2.5 mA, and it is pulled to ground through 5 kΩ when VCC is below UVLO. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reference output voltage | VREF | 4.925 | 5 | 5.075 | V | TJ=25°C, I=0.2 mA, UCC2804-Q1 | 7 |
| Reference load regulation | 10 | 30 | mV | 0.2 mA < I < 5 mA | 7 | ||
| Reference line regulation | 1.9 | 2.5 | mV/V | VCC=10 V to clamp (IVCC=25 mA); typ at TJ=25°C, max at TJ=-40°C to 125°C | 7 | ||
| Reference total variation | 4.88 | 5 | 5.1 | V | UCC2804-Q1 | 7 | |
| Output noise voltage | 130 | µV | 10 Hz ≤ f ≤ 10 kHz, TJ=25°C | 7 | |||
| Long term stability | 5 | mV | TA=125°C, 1000 hours | 7 | |||
| Reference output short circuit | -35 | -5 | mA | 7 | |||
| Oscillator frequency | 40 | 46 | 52 | kHz | UCC2804-Q1 | 7 | |
| Oscillator temperature stability | 2.5 | % | 7 | ||||
| Oscillator amplitude peak-to-peak | 2.25 | 2.4 | 2.55 | V | 7 | ||
| Oscillator peak voltage | 2.45 | V | 7 | ||||
| Error amplifier input voltage | 2.44 | 2.5 | 2.56 | V | COMP = 2.5 V, UCC2804-Q1 | 7 | |
| Error amplifier input bias current | -1 | 1 | µA | 7 | |||
| Open loop voltage gain | 60 | 80 | dB | 7 | |||
| COMP sink current | 0.3 | 3.5 | mA | FB = 2.7 V, COMP = 1.1 V | 7 | ||
| COMP source current | -0.8 | -0.5 | -0.2 | mA | FB = 1.8 V, COMP = REF, 1.2 V | 7 | |
| Gain bandwidth product | 2 | MHz | 7 | ||||
| Maximum duty cycle | 48 | 49 | 50 | % | UCC2804-Q1 | 8 | |
| Current sense gain | 1.1 | 1.65 | 1.8 | V/V | 0 ≤ VCS ≤ 0.8 V | 8 | |
| Current sense maximum input signal | 0.9 | 1 | 1.1 | V | COMP = 5 V | 8 | |
| Current sense input bias current | -200 | 200 | nA | 8 | |||
| CS blank time | 50 | 100 | 150 | ns | 8 | ||
| Overcurrent threshold | 1.42 | 1.55 | 1.68 | V | 8 | ||
| COMP to CS offset | 0.45 | 0.9 | 1.35 | V | CS = 0 V | 8 | |
| OUT low level | 0.1 | 0.4 | V | I = 20 mA, all parts | 8 | ||
| OUT low level | 0.35 | 0.9 | V | I = 200 mA, all parts | 8 | ||
| OUT low level | 0.7 | 1.2 | V | I = 20 mA, VCC = 0 V, all parts | 8 | ||
| OUT high VSAT (VCC-OUT) | 0.15 | 0.4 | V | I = 20 mA, all parts | 8 | ||
| OUT high VSAT (VCC-OUT) | 1 | 1.9 | V | I = 200 mA, all parts | 8 | ||
| Rise time | 41 | 70 | ns | CL = 1 nF | 8 | ||
| Fall time | 44 | 75 | ns | CL = 1 nF | 8 | ||
| UVLO start threshold | 11.5 | 12.5 | 13.5 | V | UCC2802-Q1 and UCC2804-Q1 | 8 | |
| UVLO stop threshold | 7.6 | 8.3 | 9 | V | UCC2802-Q1 and UCC2804-Q1 | 8 | |
| Start to stop hysteresis | 3.5 | 4.2 | 5.1 | V | UCC2802-Q1 and UCC2804-Q1 | 8 | |
| COMP rise time | 4 | 10 | ms | FB = 1.8 V, rise from 0.5 V to REF, 1 V | 8 | ||
| Start-up current | 0.1 | 0.2 | mA | VCC < start threshold | 8 | ||
| Operating supply current | 0.5 | 1 | mA | FB = 0 V, CS = 0 V | 8 | ||
| VCC internal Zener voltage | 12 | 13.5 | 15 | V | ICC = 10 mA | 8 | |
| VCC internal Zener voltage minus start threshold voltage | 0.5 | 1 | V | UCC2802-Q1 and UCC2804-Q1 | 8 | ||
| VCC voltage | 12 | V | driven from low impedance source, ICC not exceeding 30 mA | 6 | |||
| VCC current | 30 | mA | 6 | ||||
| OUT current | -1 | 1 | A | 6 | |||
| OUT energy (capacitive load) | 20 | µJ | 6 | ||||
| Analog inputs (FB, CS, RC, COMP) | -0.3 | 6.3 | V | 6.3 or VCC + 0.3, return the lesser | 6 | ||
| Power dissipation, D package | 0.65 | W | TA < 25°C | 6 | |||
| Lead temperature, soldering | 300 | °C | 10 s | 6 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 6 | ||
| Junction temperature | TJ | -55 | 150 | °C | 6 | ||
| ESD HBM | V(ESD) | -2500 | 2500 | V | per AEC Q100-002, D package | 6 | |
| ESD CDM | V(ESD) | -1500 | 1500 | V | per AEC Q100-011, D package | 6 | |
| VCC bias supply voltage | VVCC | 11 | V | from low impedance source | 6 | ||
| Voltage on analog pins | VFB, VCS, VRC, VCOMP | -0.1 | 6 | V | 6 or VVCC | 6 | |
| Gate driver output voltage | VOUT | -0.1 | V | max VVCC | 6 | ||
| Supply bias current | IVCC | 25 | mA | 6 | |||
| Average OUT pin current | IOUT | 20 | mA | 6 | |||
| REF pin output current | IREF | 5 | mA | 6 | |||
| Oscillator frequency | fOSC | 1 | MHz | 6 | |||
| Operating free-air temperature | TA | -55 | 125 | °C | 6 | ||
| Junction temperature | TJ | -55 | 125 | °C | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 107.5 | °C/W | D (SOIC) 8 pins | 7 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 49.3 | °C/W | D (SOIC) 8 pins | 7 | ||
| Junction-to-board thermal resistance | RθJB | 48.7 | °C/W | D (SOIC) 8 pins | 7 |
CAD (KiCad official)
- Symbol:
UCC2804QDRQ1 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
ucc2804qdrq1-etched.step/ucc2804qdrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc2804qdrq1.step/ucc2804qdrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (47 pp, sha256
8f4c7912c58a9b47, retrieved 2026-10-31, tier: manufacturer) (maker link no longer resolves; copy stored with this page) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# UCC2804QDRQ1
**Texas Instruments** · AC-DC Controllers & Regulators · SOIC-8
UCC2804QDRQ1 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | output | Output of the low-impedance 2-MHz error amplifier and input of the PWM comparator; it can source and sink current, is internally current-limited so forcing it to GND commands zero duty cycle, and carries the soft-start clamp. |
| 2 | FB | input | Inverting input of the error amplifier; keep lead length and stray capacitance as small as possible for best stability. |
| 3 | CS | input | Input to the PWM and overcurrent comparators with 100-ns leading-edge blanking after the OUT rising edge; exceeding the overcurrent threshold causes a soft-start cycle. |
| 4 | RC | input | Oscillator timing pin: resistor from REF to RC (10 kΩ to 200 kΩ recommended) and capacitor from RC to GND (100 pF to 1000 pF) set the frequency. |
| 5 | GND | power_in | Reference ground and power ground for all functions on the part. |
| 6 | OUT | output | High-current gate driver output capable of peak currents exceeding ±750 mA (±1 A absolute maximum), actively held low when VCC is below the UVLO threshold. |
| 7 | VCC | power_in | Power input, fed through a current-limiting resistor with 12 V absolute maximum from a low-impedance source and 30 mA maximum current; bypass with at least 1 µF in parallel with 0.1 µF ceramic to GND. |
| 8 | REF | power_out | Voltage reference output (5 V, or 4 V for UCC2803/05) bypassed with at least 0.1 µF ceramic to GND; extra bypassing is needed for loads above 2.5 mA, and it is pulled to ground through 5 kΩ when VCC is below UVLO. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reference output voltage | VREF | 4.925 | 5 | 5.075 | V | TJ=25°C, I=0.2 mA, UCC2804-Q1 | 7 |
| Reference load regulation | | | 10 | 30 | mV | 0.2 mA < I < 5 mA | 7 |
| Reference line regulation | | | 1.9 | 2.5 | mV/V | VCC=10 V to clamp (IVCC=25 mA); typ at TJ=25°C, max at TJ=-40°C to 125°C | 7 |
| Reference total variation | | 4.88 | 5 | 5.1 | V | UCC2804-Q1 | 7 |
| Output noise voltage | | | 130 | | µV | 10 Hz ≤ f ≤ 10 kHz, TJ=25°C | 7 |
| Long term stability | | | 5 | | mV | TA=125°C, 1000 hours | 7 |
| Reference output short circuit | | -35 | -5 | | mA | | 7 |
| Oscillator frequency | | 40 | 46 | 52 | kHz | UCC2804-Q1 | 7 |
| Oscillator temperature stability | | | 2.5 | | % | | 7 |
| Oscillator amplitude peak-to-peak | | 2.25 | 2.4 | 2.55 | V | | 7 |
| Oscillator peak voltage | | | 2.45 | | V | | 7 |
| Error amplifier input voltage | | 2.44 | 2.5 | 2.56 | V | COMP = 2.5 V, UCC2804-Q1 | 7 |
| Error amplifier input bias current | | -1 | | 1 | µA | | 7 |
| Open loop voltage gain | | 60 | 80 | | dB | | 7 |
| COMP sink current | | 0.3 | 3.5 | | mA | FB = 2.7 V, COMP = 1.1 V | 7 |
| COMP source current | | -0.8 | -0.5 | -0.2 | mA | FB = 1.8 V, COMP = REF, 1.2 V | 7 |
| Gain bandwidth product | | | 2 | | MHz | | 7 |
| Maximum duty cycle | | 48 | 49 | 50 | % | UCC2804-Q1 | 8 |
| Current sense gain | | 1.1 | 1.65 | 1.8 | V/V | 0 ≤ VCS ≤ 0.8 V | 8 |
| Current sense maximum input signal | | 0.9 | 1 | 1.1 | V | COMP = 5 V | 8 |
| Current sense input bias current | | -200 | | 200 | nA | | 8 |
| CS blank time | | 50 | 100 | 150 | ns | | 8 |
| Overcurrent threshold | | 1.42 | 1.55 | 1.68 | V | | 8 |
| COMP to CS offset | | 0.45 | 0.9 | 1.35 | V | CS = 0 V | 8 |
| OUT low level | | | 0.1 | 0.4 | V | I = 20 mA, all parts | 8 |
| OUT low level | | | 0.35 | 0.9 | V | I = 200 mA, all parts | 8 |
| OUT low level | | | 0.7 | 1.2 | V | I = 20 mA, VCC = 0 V, all parts | 8 |
| OUT high VSAT (VCC-OUT) | | | 0.15 | 0.4 | V | I = 20 mA, all parts | 8 |
| OUT high VSAT (VCC-OUT) | | | 1 | 1.9 | V | I = 200 mA, all parts | 8 |
| Rise time | | | 41 | 70 | ns | CL = 1 nF | 8 |
| Fall time | | | 44 | 75 | ns | CL = 1 nF | 8 |
| UVLO start threshold | | 11.5 | 12.5 | 13.5 | V | UCC2802-Q1 and UCC2804-Q1 | 8 |
| UVLO stop threshold | | 7.6 | 8.3 | 9 | V | UCC2802-Q1 and UCC2804-Q1 | 8 |
| Start to stop hysteresis | | 3.5 | 4.2 | 5.1 | V | UCC2802-Q1 and UCC2804-Q1 | 8 |
| COMP rise time | | | 4 | 10 | ms | FB = 1.8 V, rise from 0.5 V to REF, 1 V | 8 |
| Start-up current | | | 0.1 | 0.2 | mA | VCC < start threshold | 8 |
| Operating supply current | | | 0.5 | 1 | mA | FB = 0 V, CS = 0 V | 8 |
| VCC internal Zener voltage | | 12 | 13.5 | 15 | V | ICC = 10 mA | 8 |
| VCC internal Zener voltage minus start threshold voltage | | 0.5 | 1 | | V | UCC2802-Q1 and UCC2804-Q1 | 8 |
| VCC voltage | | | | 12 | V | driven from low impedance source, ICC not exceeding 30 mA | 6 |
| VCC current | | | | 30 | mA | | 6 |
| OUT current | | -1 | | 1 | A | | 6 |
| OUT energy (capacitive load) | | | | 20 | µJ | | 6 |
| Analog inputs (FB, CS, RC, COMP) | | -0.3 | | 6.3 | V | 6.3 or VCC + 0.3, return the lesser | 6 |
| Power dissipation, D package | | | | 0.65 | W | TA < 25°C | 6 |
| Lead temperature, soldering | | | | 300 | °C | 10 s | 6 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 6 |
| Junction temperature | TJ | -55 | | 150 | °C | | 6 |
| ESD HBM | V(ESD) | -2500 | | 2500 | V | per AEC Q100-002, D package | 6 |
| ESD CDM | V(ESD) | -1500 | | 1500 | V | per AEC Q100-011, D package | 6 |
| VCC bias supply voltage | VVCC | | | 11 | V | from low impedance source | 6 |
| Voltage on analog pins | VFB, VCS, VRC, VCOMP | -0.1 | | 6 | V | 6 or VVCC | 6 |
| Gate driver output voltage | VOUT | -0.1 | | | V | max VVCC | 6 |
| Supply bias current | IVCC | | | 25 | mA | | 6 |
| Average OUT pin current | IOUT | | | 20 | mA | | 6 |
| REF pin output current | IREF | | | 5 | mA | | 6 |
| Oscillator frequency | fOSC | | | 1 | MHz | | 6 |
| Operating free-air temperature | TA | -55 | | 125 | °C | | 6 |
| Junction temperature | TJ | -55 | | 125 | °C | | 6 |
| Junction-to-ambient thermal resistance | RθJA | | 107.5 | | °C/W | D (SOIC) 8 pins | 7 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 49.3 | | °C/W | D (SOIC) 8 pins | 7 |
| Junction-to-board thermal resistance | RθJB | | 48.7 | | °C/W | D (SOIC) 8 pins | 7 |
## CAD (KiCad official)
- Symbol: `UCC2804QDRQ1`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files: `ucc2804qdrq1-etched.step` / `ucc2804qdrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2804qdrq1.step` / `ucc2804qdrq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](docs/ucc2804qdrq1-datasheet.pdf) (47 pp, sha256 `8f4c7912c58a9b47`, retrieved 2026-10-31, tier: manufacturer) (maker link no longer resolves; copy stored with this page)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ucc2804qdrq1-datasheet.pdf)