main
Ray
Publish 0.1.3
bc65483
UCC21755QDWRQ1
Texas Instruments · Gate Drive ICs · SOIC-16
UCC21755QDWRQ1 from Texas Instruments, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AIN | input | Isolated analog sensing input referenced to COM; place a small capacitor to COM for noise immunity, and tie to COM if unused. |
| 2 | DESAT | input | Desaturation current protection input referenced to COM; tie to COM if unused. |
| 3 | COM | power_in | Common ground reference for the output side, connected to the IGBT emitter or SiC MOSFET source. |
| 4 | OUTH | output | Gate driver pull-up output. |
| 5 | VDD | power_in | Positive gate drive supply rail (13 V to 33 V recommended range); bypass with a >10-µF capacitor to COM placed close to the pin. |
| 6 | OUTL | output | Gate driver pull-down output. |
| 7 | CLMPI | input | Internal active Miller clamp connected directly to the power transistor gate; leave floating or tie to VEE if unused. |
| 8 | VEE | power_in | Negative gate drive supply rail (-16 V to 0 V recommended range); bypass with a >10-µF capacitor to COM placed close to the pin. |
| 9 | GND | power_in | Input-side power supply and logic ground reference. |
| 10 | IN+ | input | Non-inverting gate driver control input with 40 ns deglitch filter; tie to VCC if unused. |
| 11 | IN- | input | Inverting gate driver control input with 40 ns deglitch filter; tie to GND if unused. |
| 12 | RDY | output | Open-drain power-good output for VCC-GND and VDD-COM, which can be paralleled with other RDY pins. |
| 13 | FLT | output | Open-drain active-low fault alarm output asserted on overcurrent or short circuit, which can be paralleled with other fault pins. |
| 14 | RST/EN | input | Enables or shuts down the output side (low turns the FET off) and resets a DESAT fault when held low for more than 1000 ns; tie to IN+ for automatic reset. |
| 15 | VCC | power_in | Input-side power supply from 3 V to 5.5 V; bypass with a >1-µF capacitor to GND placed close to the pin. |
| 16 | APWM | output | Isolated analog-sensing PWM output on the input side; leave floating if unused. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16 |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC supply voltage (VCC - GND) | VCC | -0.3 | 6 | V | 4 | ||
| VDD supply voltage (VDD - COM) | VDD | -0.3 | 36 | V | 4 | ||
| VEE supply voltage (VEE - COM) | VEE | -17.5 | 0.3 | V | 4 | ||
| VDD - VEE supply voltage | VMAX | -0.3 | 36 | V | 4 | ||
| Input pins IN+, IN-, RST/EN DC voltage | IN+, IN-, RST/EN | -0.3 | V | DC, reference GND; printed max is VCC | 4 | ||
| Input pins IN+, IN-, RST/EN transient voltage | IN+, IN-, RST/EN | -5 | V | Transient, less than 100 ns, reference GND; printed max is VCC+5.0 | 4 | ||
| DESAT pin voltage | DESAT | -0.3 | V | Reference COM; printed max is VDD+0.3 | 4 | ||
| AIN pin voltage | AIN | -0.3 | 5 | V | Reference to COM | 4 | |
| RDY, FLT, APWM pin voltage | RDY, FLT, APWM | -0.3 | V | Reference GND; printed max is VCC | 4 | ||
| FLT and RDY pin input current | IFLT, IRDY | 20 | mA | 4 | |||
| APWM pin output current | IAPWM | 20 | mA | 4 | |||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| VCC supply voltage (VCC - GND) | VCC | 3 | 5.5 | V | 4 | ||
| VDD supply voltage (VDD - COM) | VDD | 13 | 33 | V | 4 | ||
| VEE supply voltage (VEE - COM) | VEE | -16 | 0 | V | 4 | ||
| VDD - VEE supply voltage | VMAX | 33 | V | 4 | |||
| Low-level input voltage IN+, IN-, RST/EN | VINL | 0 | V | Reference to GND; printed max is 0.3xVCC | 4 | ||
| AIN analog sensing input voltage | AIN | 0.6 | 4.5 | V | Reference to COM | 4 | |
| Minimum pulse width that resets the fault | tRST/EN | 1000 | ns | 4 | |||
| Ambient temperature | TA | -40 | 125 | °C | 4 | ||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| VCC UVLO ON threshold (VCC - GND) | VVCC_ON | 2.55 | 2.7 | 2.85 | V | 7 | |
| VCC UVLO OFF threshold (VCC - GND) | VVCC_OFF | 2.35 | 2.5 | 2.65 | V | 7 | |
| VCC UVLO on delay to output high | tVCC+ to OUT | 28 | 37.8 | 50 | µs | IN+ = VCC, IN- = GND | 7 |
| VCC UVLO off delay to output low | tVCC- to OUT | 5 | 10 | 15 | µs | 7 | |
| VCC UVLO on delay to RDY high | tVCC+ to RDY | 30 | 37.8 | 50 | µs | RST/EN = VCC | 7 |
| VCC UVLO off delay to RDY low | tVCC- to RDY | 5 | 10 | 15 | µs | 7 | |
| VDD UVLO ON threshold (VDD - COM) | VVDD_ON | 10.5 | 12 | 12.8 | V | 7 | |
| VDD UVLO OFF threshold (VDD - COM) | VVDD_OFF | 9.9 | 10.7 | 11.8 | V | 7 | |
| VDD UVLO on delay to output high | tVDD+ to OUT | 2 | 5 | 8 | µs | IN+ = VCC, IN- = GND | 7 |
| VCC quiescent current, output high | IVCCQ | 2.5 | 3 | 4 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 7 |
| VCC quiescent current, output low | IVCCQ | 1.45 | 2 | 2.75 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 7 |
| VDD quiescent current, output high | IVDDQ | 3.6 | 4 | 5.9 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 7 |
| VDD quiescent current, output low | IVDDQ | 3.1 | 3.7 | 5.3 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 7 |
| IN+, IN- and RST/EN deglitch filter time (ON and OFF) | TINFIL | 28 | 40 | 60 | ns | fS = 50kHz | 7 |
| Deglitch filter time to reset FLT | TRSTFIL | 500 | 650 | 800 | ns | 7 | |
| Output active pull down on OUTL | VOUTPD | 1.5 | 2 | 2.5 | V | IOUTL(typ) = 0.1×IOUTL(typ), VDD=OPEN, VEE=COM | 7 |
| Miller clamp threshold voltage | VCLMPTH | 1.5 | 2 | 2.5 | V | Reference to VEE | 8 |
| DESAT blanking capacitor charge current | ICHG | 430 | 500 | 570 | µA | VDESAT = 2.0V | 8 |
| DESAT detection threshold | VDESAT | 4.6 | 5 | 5.47 | V | 8 | |
| DESAT leading edge blank time | tDESATLEB | 150 | 200 | 450 | ns | 8 | |
| DESAT deglitch filter | tDESATFIL | 50 | 140 | 230 | ns | 8 | |
| DESAT propagation delay to OUTL 90% | tDESATOFF | 150 | 200 | 300 | ns | 8 | |
| DESAT to FLT low delay | tDESATFLT | 400 | 580 | 750 | ns | 8 | |
| Soft turn-off current on fault condition | ISTO | 250 | 400 | 570 | mA | VDD-VEE = 20 V, OUTL = 8 V | 8 |
| Internal current source | IAIN | 196 | 203 | 209 | µA | VAIN=2.5V, -40°C< TJ< 150°C | 8 |
| APWM output frequency | fAPWM | 380 | 400 | 420 | kHz | VAIN=2.5V | 8 |
| APWM duty cycle | DAPWM | 86.5 | 88 | 89.5 | % | VAIN=0.6V | 8 |
| APWM duty cycle | DAPWM | 48.5 | 50 | 51.5 | % | VAIN=2.5V | 8 |
| APWM duty cycle | DAPWM | 7.5 | 10 | 11.5 | % | VAIN=4.5V | 8 |
| Propagation delay time low-to-high | tPDLH | 60 | 90 | 130 | ns | 9 | |
| Propagation delay time high-to-low (printed as low-to-high) | tPDHL | 60 | 90 | 130 | ns | 9 | |
| Pulse width distortion (tPDHL-tPDLH) | PWD | 30 | ns | 9 | |||
| Part to part skew | tsk-pp | 30 | ns | Rising or falling propagation delay | 9 | ||
| Junction-to-ambient thermal resistance | RθJA | 68.3 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 27.5 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 32.9 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ΨJT | 14.1 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ΨJB | 32.3 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
UCC21755QDWRQ1 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
ucc21755qdwrq1-etched.step/ucc21755qdwrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc21755qdwrq1.step/ucc21755qdwrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (53 pp, sha256
59845406f83fad22, retrieved 2026-11-17) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# UCC21755QDWRQ1
**Texas Instruments** · Gate Drive ICs · SOIC-16
UCC21755QDWRQ1 from Texas Instruments, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AIN | input | Isolated analog sensing input referenced to COM; place a small capacitor to COM for noise immunity, and tie to COM if unused. |
| 2 | DESAT | input | Desaturation current protection input referenced to COM; tie to COM if unused. |
| 3 | COM | power_in | Common ground reference for the output side, connected to the IGBT emitter or SiC MOSFET source. |
| 4 | OUTH | output | Gate driver pull-up output. |
| 5 | VDD | power_in | Positive gate drive supply rail (13 V to 33 V recommended range); bypass with a >10-µF capacitor to COM placed close to the pin. |
| 6 | OUTL | output | Gate driver pull-down output. |
| 7 | CLMPI | input | Internal active Miller clamp connected directly to the power transistor gate; leave floating or tie to VEE if unused. |
| 8 | VEE | power_in | Negative gate drive supply rail (-16 V to 0 V recommended range); bypass with a >10-µF capacitor to COM placed close to the pin. |
| 9 | GND | power_in | Input-side power supply and logic ground reference. |
| 10 | IN+ | input | Non-inverting gate driver control input with 40 ns deglitch filter; tie to VCC if unused. |
| 11 | IN- | input | Inverting gate driver control input with 40 ns deglitch filter; tie to GND if unused. |
| 12 | RDY | output | Open-drain power-good output for VCC-GND and VDD-COM, which can be paralleled with other RDY pins. |
| 13 | FLT | output | Open-drain active-low fault alarm output asserted on overcurrent or short circuit, which can be paralleled with other fault pins. |
| 14 | RST/EN | input | Enables or shuts down the output side (low turns the FET off) and resets a DESAT fault when held low for more than 1000 ns; tie to IN+ for automatic reset. |
| 15 | VCC | power_in | Input-side power supply from 3 V to 5.5 V; bypass with a >1-µF capacitor to GND placed close to the pin. |
| 16 | APWM | output | Isolated analog-sensing PWM output on the input side; leave floating if unused. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16 |
| Category | Power Supply Chip |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC supply voltage (VCC - GND) | VCC | -0.3 | | 6 | V | | 4 |
| VDD supply voltage (VDD - COM) | VDD | -0.3 | | 36 | V | | 4 |
| VEE supply voltage (VEE - COM) | VEE | -17.5 | | 0.3 | V | | 4 |
| VDD - VEE supply voltage | VMAX | -0.3 | | 36 | V | | 4 |
| Input pins IN+, IN-, RST/EN DC voltage | IN+, IN-, RST/EN | -0.3 | | | V | DC, reference GND; printed max is VCC | 4 |
| Input pins IN+, IN-, RST/EN transient voltage | IN+, IN-, RST/EN | -5 | | | V | Transient, less than 100 ns, reference GND; printed max is VCC+5.0 | 4 |
| DESAT pin voltage | DESAT | -0.3 | | | V | Reference COM; printed max is VDD+0.3 | 4 |
| AIN pin voltage | AIN | -0.3 | | 5 | V | Reference to COM | 4 |
| RDY, FLT, APWM pin voltage | RDY, FLT, APWM | -0.3 | | | V | Reference GND; printed max is VCC | 4 |
| FLT and RDY pin input current | IFLT, IRDY | | | 20 | mA | | 4 |
| APWM pin output current | IAPWM | | | 20 | mA | | 4 |
| Junction temperature | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| VCC supply voltage (VCC - GND) | VCC | 3 | | 5.5 | V | | 4 |
| VDD supply voltage (VDD - COM) | VDD | 13 | | 33 | V | | 4 |
| VEE supply voltage (VEE - COM) | VEE | -16 | | 0 | V | | 4 |
| VDD - VEE supply voltage | VMAX | | | 33 | V | | 4 |
| Low-level input voltage IN+, IN-, RST/EN | VINL | 0 | | | V | Reference to GND; printed max is 0.3xVCC | 4 |
| AIN analog sensing input voltage | AIN | 0.6 | | 4.5 | V | Reference to COM | 4 |
| Minimum pulse width that resets the fault | tRST/EN | 1000 | | | ns | | 4 |
| Ambient temperature | TA | -40 | | 125 | °C | | 4 |
| Junction temperature | TJ | -40 | | 150 | °C | | 4 |
| VCC UVLO ON threshold (VCC - GND) | VVCC_ON | 2.55 | 2.7 | 2.85 | V | | 7 |
| VCC UVLO OFF threshold (VCC - GND) | VVCC_OFF | 2.35 | 2.5 | 2.65 | V | | 7 |
| VCC UVLO on delay to output high | tVCC+ to OUT | 28 | 37.8 | 50 | µs | IN+ = VCC, IN- = GND | 7 |
| VCC UVLO off delay to output low | tVCC- to OUT | 5 | 10 | 15 | µs | | 7 |
| VCC UVLO on delay to RDY high | tVCC+ to RDY | 30 | 37.8 | 50 | µs | RST/EN = VCC | 7 |
| VCC UVLO off delay to RDY low | tVCC- to RDY | 5 | 10 | 15 | µs | | 7 |
| VDD UVLO ON threshold (VDD - COM) | VVDD_ON | 10.5 | 12 | 12.8 | V | | 7 |
| VDD UVLO OFF threshold (VDD - COM) | VVDD_OFF | 9.9 | 10.7 | 11.8 | V | | 7 |
| VDD UVLO on delay to output high | tVDD+ to OUT | 2 | 5 | 8 | µs | IN+ = VCC, IN- = GND | 7 |
| VCC quiescent current, output high | IVCCQ | 2.5 | 3 | 4 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 7 |
| VCC quiescent current, output low | IVCCQ | 1.45 | 2 | 2.75 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 7 |
| VDD quiescent current, output high | IVDDQ | 3.6 | 4 | 5.9 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 7 |
| VDD quiescent current, output low | IVDDQ | 3.1 | 3.7 | 5.3 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 7 |
| IN+, IN- and RST/EN deglitch filter time (ON and OFF) | TINFIL | 28 | 40 | 60 | ns | fS = 50kHz | 7 |
| Deglitch filter time to reset FLT | TRSTFIL | 500 | 650 | 800 | ns | | 7 |
| Output active pull down on OUTL | VOUTPD | 1.5 | 2 | 2.5 | V | IOUTL(typ) = 0.1×IOUTL(typ), VDD=OPEN, VEE=COM | 7 |
| Miller clamp threshold voltage | VCLMPTH | 1.5 | 2 | 2.5 | V | Reference to VEE | 8 |
| DESAT blanking capacitor charge current | ICHG | 430 | 500 | 570 | µA | VDESAT = 2.0V | 8 |
| DESAT detection threshold | VDESAT | 4.6 | 5 | 5.47 | V | | 8 |
| DESAT leading edge blank time | tDESATLEB | 150 | 200 | 450 | ns | | 8 |
| DESAT deglitch filter | tDESATFIL | 50 | 140 | 230 | ns | | 8 |
| DESAT propagation delay to OUTL 90% | tDESATOFF | 150 | 200 | 300 | ns | | 8 |
| DESAT to FLT low delay | tDESATFLT | 400 | 580 | 750 | ns | | 8 |
| Soft turn-off current on fault condition | ISTO | 250 | 400 | 570 | mA | VDD-VEE = 20 V, OUTL = 8 V | 8 |
| Internal current source | IAIN | 196 | 203 | 209 | µA | VAIN=2.5V, -40°C< TJ< 150°C | 8 |
| APWM output frequency | fAPWM | 380 | 400 | 420 | kHz | VAIN=2.5V | 8 |
| APWM duty cycle | DAPWM | 86.5 | 88 | 89.5 | % | VAIN=0.6V | 8 |
| APWM duty cycle | DAPWM | 48.5 | 50 | 51.5 | % | VAIN=2.5V | 8 |
| APWM duty cycle | DAPWM | 7.5 | 10 | 11.5 | % | VAIN=4.5V | 8 |
| Propagation delay time low-to-high | tPDLH | 60 | 90 | 130 | ns | | 9 |
| Propagation delay time high-to-low (printed as low-to-high) | tPDHL | 60 | 90 | 130 | ns | | 9 |
| Pulse width distortion (tPDHL-tPDLH) | PWD | | | 30 | ns | | 9 |
| Part to part skew | tsk-pp | | | 30 | ns | Rising or falling propagation delay | 9 |
| Junction-to-ambient thermal resistance | RθJA | | 68.3 | | °C/W | | 5 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 27.5 | | °C/W | | 5 |
| Junction-to-board thermal resistance | RθJB | | 32.9 | | °C/W | | 5 |
| Junction-to-top characterization parameter | ΨJT | | 14.1 | | °C/W | | 5 |
| Junction-to-board characterization parameter | ΨJB | | 32.3 | | °C/W | | 5 |
## CAD (KiCad official)
- Symbol: `UCC21755QDWRQ1`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files: `ucc21755qdwrq1-etched.step` / `ucc21755qdwrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc21755qdwrq1.step` / `ucc21755qdwrq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc21755-q1.pdf) (53 pp, sha256 `59845406f83fad22`, retrieved 2026-11-17)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ucc21755qdwrq1-datasheet.pdf)