3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownUCC21739QDWRQ1
Texas Instruments · Isolators - Gate Drivers · SOIC-16-300mil
UCC21739QDWRQ1 from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AIN | input | Isolated analog sensing input referenced to COM, specified at 0.6 V to 4.5 V; use a small capacitor to COM for noise immunity and tie to COM if unused. |
| 2 | OC | input | Over-current detection input supporting a lower threshold for SenseFET, DESAT and shunt-resistor sensing, rated -0.3 V to 6 V referenced to COM; tie to COM if unused. |
| 3 | COM | power_in | Common ground reference for the output side, connected to the IGBT emitter or SiC MOSFET source. |
| 4 | OUTH | output | Gate driver pull-up output, rated DC from VEE-0.3 V to VDD and transient (<100 ns) from VEE-5 V to VDD+5 V. |
| 5 | VDD | power_in | Positive gate-drive supply referenced to COM, 13 V to 33 V recommended; bypass with a >10 µF capacitor to COM placed close to the pin. |
| 6 | OUTL | output | Gate driver pull-down output, rated DC from VEE-0.3 V to VDD and transient (<100 ns) from VEE-5 V to VDD+5 V. |
| 7 | CLMPE | output | External active Miller clamp drive output connecting to the gate of the external clamp MOSFET, rated -0.3 V to 5 V referenced to VEE; leave floating if unused. |
| 8 | VEE | power_in | Negative gate-drive supply referenced to COM; bypass with a >10 µF capacitor to COM to support the specified sink peak current. |
| 9 | GND | power_in | Input-side power supply and logic ground reference for VCC and the control inputs. |
| 10 | IN+ | input | Non-inverting gate driver control input referenced to GND, with high level at 0.7×VCC minimum and low level at 0.3×VCC maximum; tie to VCC if unused. |
| 11 | IN- | input | Inverting gate driver control input referenced to GND, with high level at 0.7×VCC minimum and low level at 0.3×VCC maximum; tie to GND if unused. |
| 12 | RDY | output | Open-drain power-good output for VCC-GND and VDD-COM that can be paralleled with other RDY signals, with input/output current limited to 20 mA. |
| 13 | FLT | output | Active-low open-drain fault alarm output asserted on over current or short circuit, which can be paralleled with other fault signals, with current limited to 20 mA. |
| 14 | RST/EN | input | Enables or disables the output side (a low level turns the FET off) and resets an OC fault on FLT when held low for more than 1000 ns; rated GND-0.3 V to VCC DC. |
| 15 | VCC | power_in | Input-side supply from 3.0 V to 5.5 V referenced to GND; bypass with a >1 µF capacitor to GND placed close to the pin. |
| 16 | APWM | output | Isolated analog sensing PWM output referenced to GND, with output current limited to 20 mA; leave floating if unused. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16-300mil |
| Category | Power Management (PMIC) |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC supply voltage (VCC-GND) absolute maximum | VCC | -0.3 | 6 | V | 4 | ||
| VDD supply voltage (VDD-COM) absolute maximum | VDD | -0.3 | 36 | V | 4 | ||
| VEE supply voltage (VEE-COM) absolute maximum | VEE | -17.5 | 0.3 | V | 4 | ||
| VDD-VEE absolute maximum | VMAX | -0.3 | 36 | V | 4 | ||
| AIN analog sensing input absolute maximum | AIN | -0.3 | 5 | V | Reference to COM | 4 | |
| OC input absolute maximum | OC | -0.3 | 6 | V | Reference to COM | 4 | |
| CLMPE output absolute maximum | CLMPE | -0.3 | 5 | V | Reference to VEE | 4 | |
| FLT and RDY pin input current absolute maximum | IFLT, IRDY | 20 | mA | 4 | |||
| APWM pin output current absolute maximum | IAPWM | 20 | mA | 4 | |||
| Junction temperature range absolute maximum | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 4 | ||
| VCC supply voltage (VCC-GND) recommended | VCC | 3 | 5.5 | V | 4 | ||
| VDD supply voltage (VDD-COM) recommended | VDD | 13 | 33 | V | 4 | ||
| VDD-VEE recommended maximum | VMAX | 33 | V | 4 | |||
| AIN analog sensing input recommended | AIN | 0.6 | 4.5 | V | Reference to COM | 4 | |
| Minimum RST/EN pulse width that resets the fault | tRST/EN | 800 | ns | 4 | |||
| Ambient temperature range | TA | -40 | 125 | °C | 4 | ||
| Junction temperature range recommended | TJ | -40 | 150 | °C | 4 | ||
| Maximum power dissipation (both sides) | PD | 985 | mW | VCC = 5V, VDD-COM = 20V, COM-VEE = 5V, IN+/- = 5V, 150kHz, 50% Duty Cycle for 10nF load, Ta=25oC | 5 | ||
| Maximum power dissipation by transmitter side | PD1 | 20 | mW | VCC = 5V, VDD-COM = 20V, COM-VEE = 5V, IN+/- = 5V, 150kHz, 50% Duty Cycle for 10nF load, Ta=25oC | 5 | ||
| Maximum power dissipation by receiver side | PD2 | 965 | mW | VCC = 5V, VDD-COM = 20V, COM-VEE = 5V, IN+/- = 5V, 150kHz, 50% Duty Cycle for 10nF load, Ta=25oC | 5 | ||
| VCC UVLO on threshold | VVCC_ON | 2.55 | 2.7 | 2.85 | V | 8 | |
| VCC UVLO off threshold | VVCC_OFF | 2.35 | 2.5 | 2.65 | V | 8 | |
| VCC UVLO on delay to output high | tVCC+ to OUT | 29 | 37.8 | 50 | µs | IN+ = VCC, IN- = GND | 8 |
| VCC UVLO off delay to output low | tVCC- to OUT | 5 | 10 | 15 | ns | 8 | |
| VCC UVLO on delay to RDY high | tVCC+ to RDY | 30 | 37.8 | 50 | ns | RST/EN = VCC | 8 |
| VCC UVLO off delay to RDY low | tVCC- to RDY | 5 | 10 | 15 | ns | 8 | |
| VDD UVLO on threshold | VVDD_ON | 10.5 | 12 | 12.8 | V | 8 | |
| VDD UVLO off threshold | VVDD_OFF | 9.9 | 10.7 | 11.8 | V | 8 | |
| VDD UVLO on delay to output high | tVDD+ to OUT | 2 | 5 | 8 | ns | IN+ = VCC, IN- = GND | 8 |
| VCC quiescent current with OUT high | IVCCQ | 2.5 | 3 | 4 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 8 |
| VCC quiescent current with OUT low | IVCCQ | 1.45 | 2 | 2.75 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 8 |
| VDD quiescent current with OUT high | IVDDQ | 3.6 | 4 | 5.9 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 8 |
| VDD quiescent current with OUT low | IVDDQ | 3.1 | 3.7 | 5.3 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 8 |
| IN+, IN- and RST/EN deglitch filter time (ON and OFF) | TINFIL | 28 | 40 | 60 | ns | fS = 50kHz | 8 |
| Deglitch filter time to reset FLT | TRSTFIL | 500 | 650 | 800 | ns | 8 | |
| OC detection threshold | VOCTH | 0.63 | 0.7 | 0.77 | V | 8 | |
| OC fault deglitch filter | tOCFIL | 95 | 120 | 180 | ns | 8 | |
| OC propagation delay to OUT(L) 90% | tOCOFF | 150 | 270 | 400 | ns | 8 | |
| OC to FLT low delay | tOCFLT | 300 | 530 | 750 | ns | 8 | |
| 2-level turn-off voltage threshold | V2LOFF | 8.3 | 9 | 10 | V | 8 | |
| Soft turn-off current on fault conditions | ITL3 | 500 | 900 | 1200 | mA | 8 | |
| Miller clamp threshold voltage | VCLMPTH | 1.5 | 2 | 2.5 | V | Reference to VEE | 8 |
| Miller clamp output high voltage | VCLMPE | 4.4 | 5 | 5.3 | V | Reference to VEE | 8 |
| Miller clamp peak sink current | ICLMPEL | 0.12 | 0.25 | 0.37 | A | 9 | |
| Propagation delay High to Low | tPDHL | 60 | 90 | 130 | ns | 10 | |
| Propagation delay Low to High | tPDLH | 60 | 90 | 130 | ns | 10 | |
| Analog sensing voltage range | VAIN | 0.6 | 4.5 | V | 9 | ||
| Internal current source | IAIN | 196 | 200 | 209 | µA | VAIN=2.5V, -40°C< TJ< 150°C | 9 |
| APWM output frequency | fAPWM | 380 | 400 | 420 | kHz | VAIN=2.5V | 9 |
| APWM duty cycle at VAIN 0.6V | DAPWM | 86.5 | 88 | 89.5 | % | VAIN = 0.6V | 9 |
| APWM duty cycle at VAIN 2.5V | DAPWM | 48.5 | 50 | 51.5 | % | VAIN = 2.5V | 9 |
| APWM duty cycle at VAIN 4.5V | DAPWM | 7.5 | 10 | 11.5 | % | VAIN = 4.5V | 9 |
| Junction-to-ambient thermal resistance | RθJA | 68.3 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 27.5 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 32.9 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
UCC21739QDWRQ1 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
ucc21739qdwrq1-etched.step/ucc21739qdwrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc21739qdwrq1.step/ucc21739qdwrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (60 pp, sha256
e817e0d93b4e0af2, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).