main
Ray Publish 0.1.0 34ee906
{
  "slug": "ucc21732dwr",
  "version": "0.1.0",
  "type": "component",
  "description": "TEXAS INSTRUMENTS Global Sourcing Parts, SOIC-16-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "global sourcing parts",
    "ucc21732dwr",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "ucc21732dwr.kicad_sym",
    "ucc21732dwr.kicad_mod",
    "ucc21732dwr.glb",
    "ucc21732dwr.step",
    "ucc21732dwr.lbr",
    "docs/hero.png",
    "docs/ucc21732dwr-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "ucc21732dwr-hero.glb",
    "ucc21732dwr-hero.overlay.json",
    "ucc21732dwr-etched.glb"
  ],
  "component": {
    "mpn": "UCC21732DWR",
    "manufacturer": "TEXAS INSTRUMENTS",
    "package": "SOIC-16-300mil",
    "pin_count": 16,
    "category": "Global Sourcing Parts",
    "subcategory": "Global Sourcing Parts",
    "datasheet": "https://www.ti.com/lit/ds/symlink/ucc21732.pdf",
    "parts": {
      "symbol": "ucc21732dwr.kicad_sym",
      "footprint": "ucc21732dwr.kicad_mod",
      "model_3d": "ucc21732dwr-hero.glb",
      "model_3d_plain": "ucc21732dwr-etched.glb",
      "model_3d_step": "ucc21732dwr-etched.step",
      "model_3d_step_plain": "ucc21732dwr.step",
      "lbr": "ucc21732dwr.lbr"
    },
    "distributor_links": {
      "lcsc": "C5216328",
      "digikey": "296-UCC21732DWRTR-ND",
      "mouser": "595-UCC21732DWR"
    },
    "distributor_check": {
      "checked_at": "2026-11-11T11:45:36Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "296-UCC21732DWRTR-ND",
        "status": "found"
      },
      "mouser": {
        "pn": "595-UCC21732DWR",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "AIN",
        "type": "input",
        "description": "Isolated analog sensing input referenced to COM, with a voltage range of 0.6 V to 4.5 V; a small capacitor to COM is recommended for noise immunity, and it should be tied to COM if unused."
      },
      {
        "number": "2",
        "name": "OC",
        "type": "input",
        "description": "Overcurrent detection input referenced to COM with a 0.7 V typical detection threshold, supporting SenseFET, DESAT and shunt resistor sensing; tie to COM if unused."
      },
      {
        "number": "3",
        "name": "COM",
        "type": "power_in",
        "description": "Common ground reference for the output side, connected to the emitter of an IGBT or the source of a SiC MOSFET."
      },
      {
        "number": "4",
        "name": "OUTH",
        "type": "output",
        "description": "Gate driver pull-up output that sources up to 10 A peak current."
      },
      {
        "number": "5",
        "name": "VDD",
        "type": "power_in",
        "description": "Positive output-side gate drive supply, 13 V to 33 V referenced to COM, requiring a >10 µF bypass capacitor to COM placed close to the pin."
      },
      {
        "number": "6",
        "name": "OUTL",
        "type": "output",
        "description": "Gate driver pull-down output that sinks up to 10 A peak current."
      },
      {
        "number": "7",
        "name": "CLMPE",
        "type": "output",
        "description": "Gate drive output for an external active Miller clamp MOSFET, driven to about 5 V referenced to VEE; leave floating if unused."
      },
      {
        "number": "8",
        "name": "VEE",
        "type": "power_in",
        "description": "Negative output-side gate drive supply rail, requiring a >10 µF bypass capacitor to COM placed close to the pin."
      },
      {
        "number": "9",
        "name": "GND",
        "type": "power_in",
        "description": "Input-side power supply and logic ground reference."
      },
      {
        "number": "10",
        "name": "IN+",
        "type": "input",
        "description": "Non-inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to VCC if unused."
      },
      {
        "number": "11",
        "name": "IN-",
        "type": "input",
        "description": "Inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to GND if unused."
      },
      {
        "number": "12",
        "name": "RDY",
        "type": "output",
        "description": "Open-drain power-good output for VCC-GND and VDD-COM that requires an external pull-up and may be paralleled with other RDY pins."
      },
      {
        "number": "13",
        "name": "FLT",
        "type": "output",
        "description": "Open-drain active-low fault alarm output on overcurrent or short circuit that may be paralleled with other FLT pins."
      },
      {
        "number": "14",
        "name": "RST/EN",
        "type": "input",
        "description": "Enable/shutdown input (output disabled when low, with 50 kΩ internal pull-down) and fault reset input, where a low level held longer than 1000 ns resets the OC fault on the rising edge."
      },
      {
        "number": "15",
        "name": "VCC",
        "type": "power_in",
        "description": "Input-side power supply from 3 V to 5.5 V referenced to GND, requiring a >1 µF bypass capacitor to GND placed close to the pin."
      },
      {
        "number": "16",
        "name": "APWM",
        "type": "output",
        "description": "Isolated analog-to-PWM sensing output on the input side, operating at about 400 kHz; leave floating if unused."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: Pin numbers are taken from Table 4-1 (Pin Functions) on page 3 and cross-checked against the functio; The schema has no specs field, so headline electrical specs were not extracted. Pin descriptions inc"
        ],
        "pages_sent": 60,
        "cost_usd": 0.2176,
        "at": "2026-11-11T11:45:06"
      },
      "datasheet": {
        "url": "https://www.ti.com/lit/ds/symlink/ucc21732.pdf",
        "pages": 60,
        "sha256": "53c4ebd395eb0537",
        "source_tier": "mfr"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 16,
        "described": 16,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "ucc21732dwr.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          10.3,
          10.3,
          2.75
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "159663ceb2b4996b1b89d3111e4a355fc27de3e24d3570f50e5ed9086e0d73af",
        "checked": "2026-11-11",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "ucc21732dwr-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          10.3,
          10.3,
          2.75
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "0612afb4d75ee90af6e9d3528115c74ab9dca46c8bb952b2c534258235308543",
        "checked": "2026-11-11",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ],
    "package_dims": {
      "package_code": "DW0016B",
      "source_page": 57,
      "D": {
        "nom_mm": 10.3,
        "range_mm": [
          10.1,
          10.5
        ]
      },
      "E1": {
        "nom_mm": 7.5,
        "range_mm": [
          7.4,
          7.6
        ]
      },
      "E": {
        "nom_mm": 10.3,
        "range_mm": [
          9.97,
          10.63
        ]
      },
      "e": {
        "nom_mm": 1.27,
        "range_mm": [
          null,
          null
        ]
      },
      "A": {
        "nom_mm": 2.65,
        "range_mm": [
          null,
          2.65
        ]
      },
      "source": "datasheet package drawing, every number found on its page (extract_pins --task dims)",
      "model_check": {
        "file": "ucc21732dwr.step",
        "verdict": "PASS",
        "reasons": [
          "height and body within the datasheet's package drawing"
        ],
        "by": "factory/package_fit.py"
      }
    }
  }
}