Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

UCC21732DWR

TEXAS INSTRUMENTS · Global Sourcing Parts · SOIC-16-300mil

UCC21732DWR from TEXAS INSTRUMENTS, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 AIN input Isolated analog sensing input referenced to COM, with a voltage range of 0.6 V to 4.5 V; a small capacitor to COM is recommended for noise immunity, and it should be tied to COM if unused.
2 OC input Overcurrent detection input referenced to COM with a 0.7 V typical detection threshold, supporting SenseFET, DESAT and shunt resistor sensing; tie to COM if unused.
3 COM power_in Common ground reference for the output side, connected to the emitter of an IGBT or the source of a SiC MOSFET.
4 OUTH output Gate driver pull-up output that sources up to 10 A peak current.
5 VDD power_in Positive output-side gate drive supply, 13 V to 33 V referenced to COM, requiring a >10 µF bypass capacitor to COM placed close to the pin.
6 OUTL output Gate driver pull-down output that sinks up to 10 A peak current.
7 CLMPE output Gate drive output for an external active Miller clamp MOSFET, driven to about 5 V referenced to VEE; leave floating if unused.
8 VEE power_in Negative output-side gate drive supply rail, requiring a >10 µF bypass capacitor to COM placed close to the pin.
9 GND power_in Input-side power supply and logic ground reference.
10 IN+ input Non-inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to VCC if unused.
11 IN- input Inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to GND if unused.
12 RDY output Open-drain power-good output for VCC-GND and VDD-COM that requires an external pull-up and may be paralleled with other RDY pins.
13 FLT output Open-drain active-low fault alarm output on overcurrent or short circuit that may be paralleled with other FLT pins.
14 RST/EN input Enable/shutdown input (output disabled when low, with 50 kΩ internal pull-down) and fault reset input, where a low level held longer than 1000 ns resets the OC fault on the rising edge.
15 VCC power_in Input-side power supply from 3 V to 5.5 V referenced to GND, requiring a >1 µF bypass capacitor to GND placed close to the pin.
16 APWM output Isolated analog-to-PWM sensing output on the input side, operating at about 400 kHz; leave floating if unused.

Key specifications

Parameter Value
Manufacturer TEXAS INSTRUMENTS
Package SOIC-16-300mil
Category Global Sourcing Parts
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC, GND supply voltage (absolute maximum) VCC -0.3 6 V 4
VDD, COM supply voltage (absolute maximum) VDD -0.3 36 V 4
VEE, COM supply voltage (absolute maximum) VEE -17.5 0.3 V 4
VDD, VEE maximum voltage (absolute maximum) VMAX -0.3 36 V 4
AIN voltage reference to COM (absolute maximum) AIN -0.3 5 V 4
OC voltage reference to COM (absolute maximum) OC -0.3 6 V 4
CLMPE voltage reference to VEE (absolute maximum) CLMPE -0.3 5 V 4
FLT and RDY pin input current (absolute maximum) IFLT, IRDY 20 mA 4
APWM pin output current (absolute maximum) IAPWM 20 mA 4
Junction temperature range (absolute maximum) TJ -40 150 °C 4
Storage temperature range (absolute maximum) Tstg -65 150 °C 4
VCC, GND supply voltage (recommended) VCC 3 5.5 V 4
VDD, COM supply voltage (recommended) VDD 13 33 V 4
VDD, VEE supply voltage (recommended) VMAX 33 V 4
Low level input voltage, IN+, IN-, RST/EN (reference to GND) VIL 0 V 4
AIN analog sensing input (reference to COM) AIN 0.6 4.5 V 4
Minimum RST/EN pulse width to reset fault tRST/EN 1000 ns 4
Ambient temperature range (recommended) TA -40 125 °C 4
Junction temperature range (recommended) TJ -40 150 °C 4
VCC UVLO turn-on threshold (VCC-GND) VVCC_ON 2.55 2.7 2.85 V 8
VCC UVLO turn-off threshold (VCC-GND) VVCC_OFF 2.35 2.5 2.65 V 8
VDD UVLO turn-on threshold (VDD-COM) VVDD_ON 10.5 12 12.8 V 8
VDD UVLO turn-off threshold (VDD-COM) VVDD_OFF 9.9 10.7 11.8 V 8
VCC quiescent current, OUT high IVCCQ 2.5 3 4 mA OUT(H) = High, fS = 0Hz, AIN=2V 8
VCC quiescent current, OUT low IVCCQ 1.45 2 2.75 mA OUT(L) = Low, fS = 0Hz, AIN=2V 8
VDD quiescent current, OUT high IVDDQ 3.6 4 5.9 mA OUT(H) = High, fS = 0Hz, AIN=2V 8
VDD quiescent current, OUT low IVDDQ 3.1 3.7 5.3 mA OUT(L) = Low, fS = 0Hz, AIN=2V 8
Input high threshold VINH 1.85 2.31 V VCC=3.3V 8
Input low threshold VINL 0.99 1.52 V VCC=3.3V 8
Input high level leakage current IIH 90 µA VIN = VCC 8
Input low level leakage current IIL -90 µA VIN = GND 8
Input pins pull-down resistance RIND 28.5 55 113 kΩ see Section 7 for more information 8
Input pins pull-up resistance RINU 28.5 55 113 kΩ see Section 7 for more information 8
IN+, IN- and RST/EN deglitch (ON and OFF) filter time TINFIL 28 40 50 ns fS = 50kHz 8
Deglitch filter time to reset /FLT TRSTFIL 400 650 800 ns 8
Output pull-up resistance ROUTH 1.5 2.5 4.9 Ω IOUT = -0.1A 8
Output pull-down resistance ROUTL 0.1 0.3 0.7 Ω IOUT = 0.1A 8
Output active pull-down voltage on OUTL VOUTPD 1.5 2 2.5 V IOUTL or IOUT = 0.1×IOUT(L)(tpy), VDD=OPEN, VEE=COM 8
Miller clamp threshold voltage VCLMPTH 1.5 2 2.5 V Reference to VEE 8
Miller clamp output high voltage VCLMPE 4.8 5 5.3 V Reference to VEE 8
Miller clamp peak sink current ICLMPEL 0.12 0.25 0.37 A CCLMPE = 10nF 9
OC detection threshold VOCTH 0.63 0.7 0.77 V 9
OC propagation delay to OUT(L) 90% tOCOFF 150 270 400 ns 9
OC to FLT low delay tOCFLT 300 530 750 ns 9
2-level turn-off voltage threshold V2LOFF 8.3 9 10 V 9
2-level turn-off voltage duration t2LOFF 500 700 1000 ns 9
Soft turn-off current on fault conditions ITL3 500 900 1200 mA VDD-VEE=20V, VOUTL-COM=8V 9
Analog sensing voltage range VAIN 0.6 4.5 V 9
Internal current source IAIN 196 203 209 µA VAIN=2.5V, -40°C< TJ< 150°C 9
APWM output frequency fAPWM 360 400 440 kHz VAIN=2.5V 9
Common-mode transient immunity CMTI 150 V/ns VCM = 1500 V 9
APWM duty cycle DAPWM 85 88 91 % VAIN = 0.6V 9
APWM duty cycle DAPWM 47 50 53 % VAIN = 2.5V 9
APWM duty cycle DAPWM 7 10 13 % VAIN = 4.5V 9
Output pull-up resistance (gate driver) ROUTH 1.5 2.5 4.9 Ω IOUT = -0.1A 8
Propagation delay time, high to low tPDHL 60 90 130 ns 10
Propagation delay time, low to high tPDLH 60 90 130 ns 10
Pulse width distortion /tPDHL, tPDLH/ PWD 30 ns 10
Part to part skew, rising or falling propagation delay tsk-pp 30 ns Rising or Falling Propagation Delay 10
Junction-to-ambient thermal resistance RθJA 68.3 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 27.5 °C/W 5

CAD (KiCad official)

  • Symbol: UCC21732DWR
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: ucc21732dwr-etched.step / ucc21732dwr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc21732dwr.step / ucc21732dwr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TEXAS INSTRUMENTS datasheet (60 pp, sha256 53c4ebd395eb0537, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF