main
Ray
Publish 0.1.0
34ee906
UCC21732DWR
TEXAS INSTRUMENTS · Global Sourcing Parts · SOIC-16-300mil
UCC21732DWR from TEXAS INSTRUMENTS, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AIN | input | Isolated analog sensing input referenced to COM, with a voltage range of 0.6 V to 4.5 V; a small capacitor to COM is recommended for noise immunity, and it should be tied to COM if unused. |
| 2 | OC | input | Overcurrent detection input referenced to COM with a 0.7 V typical detection threshold, supporting SenseFET, DESAT and shunt resistor sensing; tie to COM if unused. |
| 3 | COM | power_in | Common ground reference for the output side, connected to the emitter of an IGBT or the source of a SiC MOSFET. |
| 4 | OUTH | output | Gate driver pull-up output that sources up to 10 A peak current. |
| 5 | VDD | power_in | Positive output-side gate drive supply, 13 V to 33 V referenced to COM, requiring a >10 µF bypass capacitor to COM placed close to the pin. |
| 6 | OUTL | output | Gate driver pull-down output that sinks up to 10 A peak current. |
| 7 | CLMPE | output | Gate drive output for an external active Miller clamp MOSFET, driven to about 5 V referenced to VEE; leave floating if unused. |
| 8 | VEE | power_in | Negative output-side gate drive supply rail, requiring a >10 µF bypass capacitor to COM placed close to the pin. |
| 9 | GND | power_in | Input-side power supply and logic ground reference. |
| 10 | IN+ | input | Non-inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to VCC if unused. |
| 11 | IN- | input | Inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to GND if unused. |
| 12 | RDY | output | Open-drain power-good output for VCC-GND and VDD-COM that requires an external pull-up and may be paralleled with other RDY pins. |
| 13 | FLT | output | Open-drain active-low fault alarm output on overcurrent or short circuit that may be paralleled with other FLT pins. |
| 14 | RST/EN | input | Enable/shutdown input (output disabled when low, with 50 kΩ internal pull-down) and fault reset input, where a low level held longer than 1000 ns resets the OC fault on the rising edge. |
| 15 | VCC | power_in | Input-side power supply from 3 V to 5.5 V referenced to GND, requiring a >1 µF bypass capacitor to GND placed close to the pin. |
| 16 | APWM | output | Isolated analog-to-PWM sensing output on the input side, operating at about 400 kHz; leave floating if unused. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TEXAS INSTRUMENTS |
| Package | SOIC-16-300mil |
| Category | Global Sourcing Parts |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC, GND supply voltage (absolute maximum) | VCC | -0.3 | 6 | V | 4 | ||
| VDD, COM supply voltage (absolute maximum) | VDD | -0.3 | 36 | V | 4 | ||
| VEE, COM supply voltage (absolute maximum) | VEE | -17.5 | 0.3 | V | 4 | ||
| VDD, VEE maximum voltage (absolute maximum) | VMAX | -0.3 | 36 | V | 4 | ||
| AIN voltage reference to COM (absolute maximum) | AIN | -0.3 | 5 | V | 4 | ||
| OC voltage reference to COM (absolute maximum) | OC | -0.3 | 6 | V | 4 | ||
| CLMPE voltage reference to VEE (absolute maximum) | CLMPE | -0.3 | 5 | V | 4 | ||
| FLT and RDY pin input current (absolute maximum) | IFLT, IRDY | 20 | mA | 4 | |||
| APWM pin output current (absolute maximum) | IAPWM | 20 | mA | 4 | |||
| Junction temperature range (absolute maximum) | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature range (absolute maximum) | Tstg | -65 | 150 | °C | 4 | ||
| VCC, GND supply voltage (recommended) | VCC | 3 | 5.5 | V | 4 | ||
| VDD, COM supply voltage (recommended) | VDD | 13 | 33 | V | 4 | ||
| VDD, VEE supply voltage (recommended) | VMAX | 33 | V | 4 | |||
| Low level input voltage, IN+, IN-, RST/EN (reference to GND) | VIL | 0 | V | 4 | |||
| AIN analog sensing input (reference to COM) | AIN | 0.6 | 4.5 | V | 4 | ||
| Minimum RST/EN pulse width to reset fault | tRST/EN | 1000 | ns | 4 | |||
| Ambient temperature range (recommended) | TA | -40 | 125 | °C | 4 | ||
| Junction temperature range (recommended) | TJ | -40 | 150 | °C | 4 | ||
| VCC UVLO turn-on threshold (VCC-GND) | VVCC_ON | 2.55 | 2.7 | 2.85 | V | 8 | |
| VCC UVLO turn-off threshold (VCC-GND) | VVCC_OFF | 2.35 | 2.5 | 2.65 | V | 8 | |
| VDD UVLO turn-on threshold (VDD-COM) | VVDD_ON | 10.5 | 12 | 12.8 | V | 8 | |
| VDD UVLO turn-off threshold (VDD-COM) | VVDD_OFF | 9.9 | 10.7 | 11.8 | V | 8 | |
| VCC quiescent current, OUT high | IVCCQ | 2.5 | 3 | 4 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 8 |
| VCC quiescent current, OUT low | IVCCQ | 1.45 | 2 | 2.75 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 8 |
| VDD quiescent current, OUT high | IVDDQ | 3.6 | 4 | 5.9 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 8 |
| VDD quiescent current, OUT low | IVDDQ | 3.1 | 3.7 | 5.3 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 8 |
| Input high threshold | VINH | 1.85 | 2.31 | V | VCC=3.3V | 8 | |
| Input low threshold | VINL | 0.99 | 1.52 | V | VCC=3.3V | 8 | |
| Input high level leakage current | IIH | 90 | µA | VIN = VCC | 8 | ||
| Input low level leakage current | IIL | -90 | µA | VIN = GND | 8 | ||
| Input pins pull-down resistance | RIND | 28.5 | 55 | 113 | kΩ | see Section 7 for more information | 8 |
| Input pins pull-up resistance | RINU | 28.5 | 55 | 113 | kΩ | see Section 7 for more information | 8 |
| IN+, IN- and RST/EN deglitch (ON and OFF) filter time | TINFIL | 28 | 40 | 50 | ns | fS = 50kHz | 8 |
| Deglitch filter time to reset /FLT | TRSTFIL | 400 | 650 | 800 | ns | 8 | |
| Output pull-up resistance | ROUTH | 1.5 | 2.5 | 4.9 | Ω | IOUT = -0.1A | 8 |
| Output pull-down resistance | ROUTL | 0.1 | 0.3 | 0.7 | Ω | IOUT = 0.1A | 8 |
| Output active pull-down voltage on OUTL | VOUTPD | 1.5 | 2 | 2.5 | V | IOUTL or IOUT = 0.1×IOUT(L)(tpy), VDD=OPEN, VEE=COM | 8 |
| Miller clamp threshold voltage | VCLMPTH | 1.5 | 2 | 2.5 | V | Reference to VEE | 8 |
| Miller clamp output high voltage | VCLMPE | 4.8 | 5 | 5.3 | V | Reference to VEE | 8 |
| Miller clamp peak sink current | ICLMPEL | 0.12 | 0.25 | 0.37 | A | CCLMPE = 10nF | 9 |
| OC detection threshold | VOCTH | 0.63 | 0.7 | 0.77 | V | 9 | |
| OC propagation delay to OUT(L) 90% | tOCOFF | 150 | 270 | 400 | ns | 9 | |
| OC to FLT low delay | tOCFLT | 300 | 530 | 750 | ns | 9 | |
| 2-level turn-off voltage threshold | V2LOFF | 8.3 | 9 | 10 | V | 9 | |
| 2-level turn-off voltage duration | t2LOFF | 500 | 700 | 1000 | ns | 9 | |
| Soft turn-off current on fault conditions | ITL3 | 500 | 900 | 1200 | mA | VDD-VEE=20V, VOUTL-COM=8V | 9 |
| Analog sensing voltage range | VAIN | 0.6 | 4.5 | V | 9 | ||
| Internal current source | IAIN | 196 | 203 | 209 | µA | VAIN=2.5V, -40°C< TJ< 150°C | 9 |
| APWM output frequency | fAPWM | 360 | 400 | 440 | kHz | VAIN=2.5V | 9 |
| Common-mode transient immunity | CMTI | 150 | V/ns | VCM = 1500 V | 9 | ||
| APWM duty cycle | DAPWM | 85 | 88 | 91 | % | VAIN = 0.6V | 9 |
| APWM duty cycle | DAPWM | 47 | 50 | 53 | % | VAIN = 2.5V | 9 |
| APWM duty cycle | DAPWM | 7 | 10 | 13 | % | VAIN = 4.5V | 9 |
| Output pull-up resistance (gate driver) | ROUTH | 1.5 | 2.5 | 4.9 | Ω | IOUT = -0.1A | 8 |
| Propagation delay time, high to low | tPDHL | 60 | 90 | 130 | ns | 10 | |
| Propagation delay time, low to high | tPDLH | 60 | 90 | 130 | ns | 10 | |
| Pulse width distortion /tPDHL, tPDLH/ | PWD | 30 | ns | 10 | |||
| Part to part skew, rising or falling propagation delay | tsk-pp | 30 | ns | Rising or Falling Propagation Delay | 10 | ||
| Junction-to-ambient thermal resistance | RθJA | 68.3 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 27.5 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
UCC21732DWR - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
ucc21732dwr-etched.step/ucc21732dwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc21732dwr.step/ucc21732dwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TEXAS INSTRUMENTS datasheet (60 pp, sha256
53c4ebd395eb0537, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# UCC21732DWR
**TEXAS INSTRUMENTS** · Global Sourcing Parts · SOIC-16-300mil
UCC21732DWR from TEXAS INSTRUMENTS, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AIN | input | Isolated analog sensing input referenced to COM, with a voltage range of 0.6 V to 4.5 V; a small capacitor to COM is recommended for noise immunity, and it should be tied to COM if unused. |
| 2 | OC | input | Overcurrent detection input referenced to COM with a 0.7 V typical detection threshold, supporting SenseFET, DESAT and shunt resistor sensing; tie to COM if unused. |
| 3 | COM | power_in | Common ground reference for the output side, connected to the emitter of an IGBT or the source of a SiC MOSFET. |
| 4 | OUTH | output | Gate driver pull-up output that sources up to 10 A peak current. |
| 5 | VDD | power_in | Positive output-side gate drive supply, 13 V to 33 V referenced to COM, requiring a >10 µF bypass capacitor to COM placed close to the pin. |
| 6 | OUTL | output | Gate driver pull-down output that sinks up to 10 A peak current. |
| 7 | CLMPE | output | Gate drive output for an external active Miller clamp MOSFET, driven to about 5 V referenced to VEE; leave floating if unused. |
| 8 | VEE | power_in | Negative output-side gate drive supply rail, requiring a >10 µF bypass capacitor to COM placed close to the pin. |
| 9 | GND | power_in | Input-side power supply and logic ground reference. |
| 10 | IN+ | input | Non-inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to VCC if unused. |
| 11 | IN- | input | Inverting gate driver control input referenced to GND with a 40 ns internal deglitch filter; tie to GND if unused. |
| 12 | RDY | output | Open-drain power-good output for VCC-GND and VDD-COM that requires an external pull-up and may be paralleled with other RDY pins. |
| 13 | FLT | output | Open-drain active-low fault alarm output on overcurrent or short circuit that may be paralleled with other FLT pins. |
| 14 | RST/EN | input | Enable/shutdown input (output disabled when low, with 50 kΩ internal pull-down) and fault reset input, where a low level held longer than 1000 ns resets the OC fault on the rising edge. |
| 15 | VCC | power_in | Input-side power supply from 3 V to 5.5 V referenced to GND, requiring a >1 µF bypass capacitor to GND placed close to the pin. |
| 16 | APWM | output | Isolated analog-to-PWM sensing output on the input side, operating at about 400 kHz; leave floating if unused. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TEXAS INSTRUMENTS |
| Package | SOIC-16-300mil |
| Category | Global Sourcing Parts |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC, GND supply voltage (absolute maximum) | VCC | -0.3 | | 6 | V | | 4 |
| VDD, COM supply voltage (absolute maximum) | VDD | -0.3 | | 36 | V | | 4 |
| VEE, COM supply voltage (absolute maximum) | VEE | -17.5 | | 0.3 | V | | 4 |
| VDD, VEE maximum voltage (absolute maximum) | VMAX | -0.3 | | 36 | V | | 4 |
| AIN voltage reference to COM (absolute maximum) | AIN | -0.3 | | 5 | V | | 4 |
| OC voltage reference to COM (absolute maximum) | OC | -0.3 | | 6 | V | | 4 |
| CLMPE voltage reference to VEE (absolute maximum) | CLMPE | -0.3 | | 5 | V | | 4 |
| FLT and RDY pin input current (absolute maximum) | IFLT, IRDY | | | 20 | mA | | 4 |
| APWM pin output current (absolute maximum) | IAPWM | | | 20 | mA | | 4 |
| Junction temperature range (absolute maximum) | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature range (absolute maximum) | Tstg | -65 | | 150 | °C | | 4 |
| VCC, GND supply voltage (recommended) | VCC | 3 | | 5.5 | V | | 4 |
| VDD, COM supply voltage (recommended) | VDD | 13 | | 33 | V | | 4 |
| VDD, VEE supply voltage (recommended) | VMAX | | | 33 | V | | 4 |
| Low level input voltage, IN+, IN-, RST/EN (reference to GND) | VIL | 0 | | | V | | 4 |
| AIN analog sensing input (reference to COM) | AIN | 0.6 | | 4.5 | V | | 4 |
| Minimum RST/EN pulse width to reset fault | tRST/EN | 1000 | | | ns | | 4 |
| Ambient temperature range (recommended) | TA | -40 | | 125 | °C | | 4 |
| Junction temperature range (recommended) | TJ | -40 | | 150 | °C | | 4 |
| VCC UVLO turn-on threshold (VCC-GND) | VVCC_ON | 2.55 | 2.7 | 2.85 | V | | 8 |
| VCC UVLO turn-off threshold (VCC-GND) | VVCC_OFF | 2.35 | 2.5 | 2.65 | V | | 8 |
| VDD UVLO turn-on threshold (VDD-COM) | VVDD_ON | 10.5 | 12 | 12.8 | V | | 8 |
| VDD UVLO turn-off threshold (VDD-COM) | VVDD_OFF | 9.9 | 10.7 | 11.8 | V | | 8 |
| VCC quiescent current, OUT high | IVCCQ | 2.5 | 3 | 4 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 8 |
| VCC quiescent current, OUT low | IVCCQ | 1.45 | 2 | 2.75 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 8 |
| VDD quiescent current, OUT high | IVDDQ | 3.6 | 4 | 5.9 | mA | OUT(H) = High, fS = 0Hz, AIN=2V | 8 |
| VDD quiescent current, OUT low | IVDDQ | 3.1 | 3.7 | 5.3 | mA | OUT(L) = Low, fS = 0Hz, AIN=2V | 8 |
| Input high threshold | VINH | 1.85 | | 2.31 | V | VCC=3.3V | 8 |
| Input low threshold | VINL | 0.99 | | 1.52 | V | VCC=3.3V | 8 |
| Input high level leakage current | IIH | | | 90 | µA | VIN = VCC | 8 |
| Input low level leakage current | IIL | -90 | | | µA | VIN = GND | 8 |
| Input pins pull-down resistance | RIND | 28.5 | 55 | 113 | kΩ | see Section 7 for more information | 8 |
| Input pins pull-up resistance | RINU | 28.5 | 55 | 113 | kΩ | see Section 7 for more information | 8 |
| IN+, IN- and RST/EN deglitch (ON and OFF) filter time | TINFIL | 28 | 40 | 50 | ns | fS = 50kHz | 8 |
| Deglitch filter time to reset /FLT | TRSTFIL | 400 | 650 | 800 | ns | | 8 |
| Output pull-up resistance | ROUTH | 1.5 | 2.5 | 4.9 | Ω | IOUT = -0.1A | 8 |
| Output pull-down resistance | ROUTL | 0.1 | 0.3 | 0.7 | Ω | IOUT = 0.1A | 8 |
| Output active pull-down voltage on OUTL | VOUTPD | 1.5 | 2 | 2.5 | V | IOUTL or IOUT = 0.1×IOUT(L)(tpy), VDD=OPEN, VEE=COM | 8 |
| Miller clamp threshold voltage | VCLMPTH | 1.5 | 2 | 2.5 | V | Reference to VEE | 8 |
| Miller clamp output high voltage | VCLMPE | 4.8 | 5 | 5.3 | V | Reference to VEE | 8 |
| Miller clamp peak sink current | ICLMPEL | 0.12 | 0.25 | 0.37 | A | CCLMPE = 10nF | 9 |
| OC detection threshold | VOCTH | 0.63 | 0.7 | 0.77 | V | | 9 |
| OC propagation delay to OUT(L) 90% | tOCOFF | 150 | 270 | 400 | ns | | 9 |
| OC to FLT low delay | tOCFLT | 300 | 530 | 750 | ns | | 9 |
| 2-level turn-off voltage threshold | V2LOFF | 8.3 | 9 | 10 | V | | 9 |
| 2-level turn-off voltage duration | t2LOFF | 500 | 700 | 1000 | ns | | 9 |
| Soft turn-off current on fault conditions | ITL3 | 500 | 900 | 1200 | mA | VDD-VEE=20V, VOUTL-COM=8V | 9 |
| Analog sensing voltage range | VAIN | 0.6 | | 4.5 | V | | 9 |
| Internal current source | IAIN | 196 | 203 | 209 | µA | VAIN=2.5V, -40°C< TJ< 150°C | 9 |
| APWM output frequency | fAPWM | 360 | 400 | 440 | kHz | VAIN=2.5V | 9 |
| Common-mode transient immunity | CMTI | 150 | | | V/ns | VCM = 1500 V | 9 |
| APWM duty cycle | DAPWM | 85 | 88 | 91 | % | VAIN = 0.6V | 9 |
| APWM duty cycle | DAPWM | 47 | 50 | 53 | % | VAIN = 2.5V | 9 |
| APWM duty cycle | DAPWM | 7 | 10 | 13 | % | VAIN = 4.5V | 9 |
| Output pull-up resistance (gate driver) | ROUTH | 1.5 | 2.5 | 4.9 | Ω | IOUT = -0.1A | 8 |
| Propagation delay time, high to low | tPDHL | 60 | 90 | 130 | ns | | 10 |
| Propagation delay time, low to high | tPDLH | 60 | 90 | 130 | ns | | 10 |
| Pulse width distortion /tPDHL, tPDLH/ | PWD | | | 30 | ns | | 10 |
| Part to part skew, rising or falling propagation delay | tsk-pp | | | 30 | ns | Rising or Falling Propagation Delay | 10 |
| Junction-to-ambient thermal resistance | RθJA | | 68.3 | | °C/W | | 5 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 27.5 | | °C/W | | 5 |
## CAD (KiCad official)
- Symbol: `UCC21732DWR`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files: `ucc21732dwr-etched.step` / `ucc21732dwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc21732dwr.step` / `ucc21732dwr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [TEXAS INSTRUMENTS datasheet](https://www.ti.com/lit/ds/symlink/ucc21732.pdf) (60 pp, sha256 `53c4ebd395eb0537`, retrieved 2026-11-11, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ucc21732dwr-datasheet.pdf)