main
Ray
tqp3m9036: the pins were read twice by one model (sonnet); say so instead of 'cross-checked by two models'
46efc34
TQP3M9036
Qorvo · Low Noise Amplifiers (LNA) - RF · DFN-8-EP(2x2)
TQP3M9036 from Qorvo, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 2 | RF In | input | RF input pin, 50 ohm internally matched; a DC block is required. |
| 3 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 4 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 5 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 6 | Shut Down | input | A high voltage turns off the device; if not connected or less than 1V the device operates normally (Vlow 0 to 0.1 V, Vhigh 0.5 V to VDD). |
| 7 | RF Out / DCBias | bidirectional | RF output pin, 50 ohm internally matched; DC bias (+3.3 to +5.25 V) must be injected through an RF bias choke/inductor. |
| 8 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Qorvo |
| Package | DFN-8-EP(2x2) |
| Category | RF & Radio |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TSTORE | -65 | 150 | °C | 2 | ||
| RF Input Power, CW | 22 | dBm | CW, 50 Ω, T=+25 °C | 2 | |||
| Device Voltage (VDD) | VDD | 7 | V | 2 | |||
| Device Voltage (VCC) | VCC | 3.3 | 5 | 5.25 | V | 2 | |
| TCASE | TCASE | -40 | 105 | °C | 2 | ||
| Tj for >106 hours MTTF | Tj | 190 | °C | for >106 hours MTTF | 2 | ||
| Operational Frequency Range | 50 | 2000 | MHz | 2 | |||
| Gain | 18.2 | 19.8 | 21.2 | dB | 2 | ||
| Noise Figure | 0.45 | 0.75 | dB | 2 | |||
| Output IP3 | 32 | 36 | dBm | Pout=+5 dBm/tone, Δf=1 MHz | 2 | ||
| Input Return Loss | 13 | dB | Note 1 | 2 | |||
| Output Return Loss | 11 | dB | Note 1 | 2 | |||
| Output P1dB | 20 | dBm | 2 | ||||
| Power Shutdown Control, On state | 0 | 0.4 | V | On state | 2 | ||
| Power Shutdown Control, Off state | 2.5 | 3.3 | V | Off state (Power down) | 2 | ||
| Current, IDD On state | IDD | 40 | 68 | 90 | mA | On state | 2 |
| Current, IDD Off state | IDD | 3 | 4 | mA | Off state (Power down) | 2 | |
| Shutdown pin current, ISD | ISD | 140 | µA | VPD ≥ 3 V | 2 | ||
| Switching Speed ON time | 1 | µs | 50%Ctrl to 90% RF | 2 | |||
| Switching Speed OFF time | 0.5 | µs | 50%Ctrl to 10% RF | 2 | |||
| Thermal Resistance, θjc | θjc | 62 | °C/W | channel to case | 2 | ||
| Pin 6 (VPD) voltage Vlow | Vlow | 0 | 0.1 | V | 2 | ||
| Pin 6 (VPD) voltage Vhigh | Vhigh | 0.5 | V | expressed as 0.5 VDD | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | Compatible with both lead-free (260°C max. reflow temp.) and tin/lead (245°C max. reflow temp.) soldering processes. Solder profiles available upon request. | 12 |
CAD (KiCad official)
- Symbol:
TQP3M9036 - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
tqp3m9036-etched.step/tqp3m9036-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tqp3m9036.step/tqp3m9036.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Qorvo datasheet, copy hosted by LCSC (12 pp, sha256
f90f98324beb667d, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TQP3M9036
**Qorvo** · Low Noise Amplifiers (LNA) - RF · DFN-8-EP(2x2)
TQP3M9036 from Qorvo, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 2 | RF In | input | RF input pin, 50 ohm internally matched; a DC block is required. |
| 3 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 4 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 5 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 6 | Shut Down | input | A high voltage turns off the device; if not connected or less than 1V the device operates normally (Vlow 0 to 0.1 V, Vhigh 0.5 V to VDD). |
| 7 | RF Out / DCBias | bidirectional | RF output pin, 50 ohm internally matched; DC bias (+3.3 to +5.25 V) must be injected through an RF bias choke/inductor. |
| 8 | NC | unconnected | No electrical connection; provide grounded land pad for PCB mounting integrity. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Qorvo |
| Package | DFN-8-EP(2x2) |
| Category | RF & Radio |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TSTORE | -65 | | 150 | °C | | 2 |
| RF Input Power, CW | | | | 22 | dBm | CW, 50 Ω, T=+25 °C | 2 |
| Device Voltage (VDD) | VDD | | | 7 | V | | 2 |
| Device Voltage (VCC) | VCC | 3.3 | 5 | 5.25 | V | | 2 |
| TCASE | TCASE | -40 | | 105 | °C | | 2 |
| Tj for >106 hours MTTF | Tj | | | 190 | °C | for >106 hours MTTF | 2 |
| Operational Frequency Range | | 50 | | 2000 | MHz | | 2 |
| Gain | | 18.2 | 19.8 | 21.2 | dB | | 2 |
| Noise Figure | | | 0.45 | 0.75 | dB | | 2 |
| Output IP3 | | 32 | 36 | | dBm | Pout=+5 dBm/tone, Δf=1 MHz | 2 |
| Input Return Loss | | | 13 | | dB | Note 1 | 2 |
| Output Return Loss | | | 11 | | dB | Note 1 | 2 |
| Output P1dB | | | 20 | | dBm | | 2 |
| Power Shutdown Control, On state | | 0 | | 0.4 | V | On state | 2 |
| Power Shutdown Control, Off state | | 2.5 | | 3.3 | V | Off state (Power down) | 2 |
| Current, IDD On state | IDD | 40 | 68 | 90 | mA | On state | 2 |
| Current, IDD Off state | IDD | | 3 | 4 | mA | Off state (Power down) | 2 |
| Shutdown pin current, ISD | ISD | | 140 | | µA | VPD ≥ 3 V | 2 |
| Switching Speed ON time | | | 1 | | µs | 50%Ctrl to 90% RF | 2 |
| Switching Speed OFF time | | | 0.5 | | µs | 50%Ctrl to 10% RF | 2 |
| Thermal Resistance, θjc | θjc | | 62 | | °C/W | channel to case | 2 |
| Pin 6 (VPD) voltage Vlow | Vlow | 0 | | 0.1 | V | | 2 |
| Pin 6 (VPD) voltage Vhigh | Vhigh | 0.5 | | | V | expressed as 0.5 VDD | 2 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | Compatible with both lead-free (260°C max. reflow temp.) and tin/lead (245°C max. reflow temp.) soldering processes. Solder profiles available upon request. | 12 |
## CAD (KiCad official)
- Symbol: `TQP3M9036`
- Footprint: `Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm`
- 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files: `tqp3m9036-etched.step` / `tqp3m9036-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tqp3m9036.step` / `tqp3m9036.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Qorvo datasheet, copy hosted by LCSC](docs/tqp3m9036-datasheet.pdf) (12 pp, sha256 `f90f98324beb667d`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tqp3m9036-datasheet.pdf)