3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS92390RHBR
Texas Instruments · LED Drivers · QFN-32-EP(5x5)
TPS92390RHBR from Texas Instruments, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LED_GND | power_in | Analog LED ground connection. |
| 2 | LED_GND | power_in | Analog LED ground connection. |
| 3 | OUT4 | passive | Analog LED current sink output 4 (-0.3 to 52 V abs max); tie to ground if unused. |
| 4 | LED_GND | power_in | LED ground connection. |
| 5 | OUT3 | passive | Analog LED current sink output 3 (-0.3 to 52 V abs max); tie to ground if unused. |
| 6 | OUT2 | passive | Analog LED current sink output 2 (-0.3 to 52 V abs max); tie to ground if unused. |
| 7 | OUT1 | passive | Analog LED current sink output 1 (-0.3 to 52 V abs max); tie to ground if unused. |
| 8 | INT | output | Device fault interrupt output, open drain; a 10-kΩ pullup resistor is recommended. |
| 9 | SDA | bidirectional | SDA for I2C interface; a 10-kΩ pullup resistor is recommended. |
| 10 | SCL | input | SCL for I2C interface; a 10-kΩ pullup resistor is recommended. |
| 11 | BST_SYNC | input | Input for synchronizing boost; when unused connect to ground to disable spread spectrum or to VDD to enable spread spectrum. |
| 12 | PWM | input | PWM input for brightness control; tie to GND if unused. |
| 13 | SGND | power_in | Signal ground. |
| 14 | LED_SET | passive | LED string configuration through external resistor; do not leave floating. |
| 15 | PWM_FSET | passive | LED dimming frequency setup through external resistor; do not leave floating. |
| 16 | BST_FSET | passive | Boost switching frequency setup through external resistor; do not leave floating. |
| 17 | MODE | passive | Dimming mode setup through external resistor; do not leave floating. |
| 18 | UVLO | input | Input voltage sense for programming the input UVLO threshold through an external resistor to VIN. |
| 19 | VSENSE_P | input | Input voltage detection for OVP protection and positive input for input current sense (3 to 48 V recommended). |
| 20 | VSENSE_N | input | Negative input for input current sense; tie to VSENSE_P if input current sense is not used. |
| 21 | SD | output | Power line FET control, open-drain output; leave floating if unused. |
| 22 | VDD | power_in | Power supply input for internal analog and digital circuits (3 to 5.5 V); connect a 10-µF capacitor to GND. |
| 23 | EN | input | Enable input. |
| 24 | C1N | passive | Negative input for charge pump flying capacitor; leave floating if feature not used. |
| 25 | C1P | passive | Positive input for charge pump flying capacitor; leave floating if feature not used. |
| 26 | CPUMP | power_out | Charge pump output; connect to VDD if charge pump is not used, and a 4.7-µF decoupling capacitor is recommended. |
| 27 | GD | output | Gate driver output for external N-FET. |
| 28 | PGND | power_in | Power ground. |
| 29 | ISNS | input | Boost current sense pin. |
| 30 | ISNSGND | power_in | Current sense resistor GND. |
| 31 | ISET | passive | LED full-scale current setup through external resistor. |
| 32 | FB | input | Boost feedback input. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-32-EP(5x5) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Shutdown mode current, VDD pin | IQ | 1 | 5 | µA | EN = L | 6 | |
| Active mode current, VDD pin (303 kHz, CP disabled) | IQ | 15 | 65 | mA | FSW = 303 kHz, PWM = H, BOOST-FET IPD25N06S4L-30, Charge Pump Disabled | 6 | |
| Active mode current, VDD pin (2200 kHz, CP disabled) | IQ | 40 | 75 | mA | FSW = 2200 kHz, PWM = H, BOOST-FET IPD25N06S4L-30, Charge Pump Disabled | 6 | |
| Active mode current, VDD pin (303 kHz, CP enabled) | IQ | 20 | 91 | mA | FSW = 303 kHz, PWM = H, BOOST-FET IPD25N06S4L-30, Charge Pump Enabled | 6 | |
| Active mode current, VDD pin (2200 kHz, CP enabled) | IQ | 65 | 104 | mA | FSW = 2200 kHz, PWM = H, BOOST-FET IPD25N06S4L-30, Charge Pump Enabled | 6 | |
| CPUMP voltage accuracy | VCPUMP | 4.8 | 5 | 5.2 | V | VDD = 3.0 to 3.6 V; ILOAD = 1 to 50 mA | 6 |
| CP switching frequency | fCP | 387 | 417 | 447 | kHz | 6 | |
| VCPUMP UVLO threshold falling | VCPUMP_UVLO | 3.95 | 4.2 | 4.4 | V | VCPUMP falling edge | 6 |
| VCPUMP UVLO threshold rising | VCPUMP_UVLO | 4.15 | 4.4 | 4.6 | V | VCPUMP rising edge | 6 |
| VCPUMP UVLO hysteresis | VCPUMP_HYS | 0.1 | 0.2 | V | 6 | ||
| Charge pump startup time | TSTART_UP | 1000 | 2000 | µs | CCPUMP = 10 µF | 6 | |
| VDD UVLO threshold falling | VDDUVLO_F | 2.68 | 2.8 | 2.92 | V | VDD falling | 6 |
| VDD UVLO threshold rising | VDDUVLO_R | 3 | V | VDD rising | 6 | ||
| VDD UVLO hysteresis | VDDUVLO_H | 0.1 | V | 6 | |||
| UVLO pin threshold | VINUVLO_TH | 0.753 | 0.777 | 0.801 | V | VUVLO falling | 6 |
| OVP threshold | VINOVP_TH | 40.8 | 43 | 45.2 | V | VSENSE_P rising | 7 |
| Input OCP threshold | VINOCP_TH | 187 | 220 | 253 | mV | RISENSE = 20 mΩ | 7 |
| Thermal shutdown threshold | TSD | 150 | 165 | 180 | °C | Temperature rising | 7 |
| Boost OVP high threshold (discharge pin) | VBST_OVPH | 48.5 | 50 | 51.8 | V | 7 | |
| SD pull down current | ISD | 250 | 325 | 400 | µA | RSD = 20 kΩ | 7 |
| SD leakage current | ISD_LEAKAGE | 1 | µA | VSD = 48 V | 7 | ||
| PWM leakage current | IPWM_LEAKAGE | 1 | µA | VPWM = 5 V | 7 | ||
| PWM input frequency | fPWM_IN | 100 | 20000 | Hz | 7 | ||
| ISET voltage | VISET | 1.17 | 1.21 | 1.25 | V | 7 | |
| ISET pin undervoltage | VISET_UVLO | 0.97 | 1 | 1.03 | V | 7 | |
| ISET resistor range | RISET | 15.6 | 104 | kΩ | IOUT = 30 mA to 200 mA | 7 | |
| LED sink current accuracy | IACC | -4 | 4 | % | RISET = 15.6 kΩ, IOUT = 150 mA, PWM = 100% | 7 | |
| LED sink current matching | IMATCH | 1 | 3.5 | % | RISET = 15.6 kΩ, IOUT = 150 mA, PWM = 100% | 7 | |
| OUTx leakage current | ILEAKAGE | 0.1 | 2.5 | µA | OUTx = VOUT = 45 V, EN= L | 7 | |
| LED dimming frequency | fDIM | 141 | 152 | 163 | Hz | PWM_FSET = 3.92 kΩ | 8 |
| LED dimming frequency | fDIM | 283 | 305 | 327 | Hz | PWM_FSET = 4.75 kΩ | 8 |
| LED dimming frequency | fDIM | 567 | 610 | 653 | Hz | PWM_FSET = 5.76 kΩ | 8 |
| LED dimming frequency | fDIM | 1135 | 1221 | 1307 | Hz | PWM_FSET = 7.87 kΩ | 8 |
| LED dimming frequency | fDIM | 2270 | 2441 | 2612 | Hz | PWM_FSET = 11 kΩ | 8 |
| LED dimming frequency | fDIM | 4541 | 4883 | 5225 | Hz | PWM_FSET = 17.8 kΩ | 8 |
| LED dimming frequency | fDIM | 9082 | 9766 | 10450 | Hz | PWM_FSET = 42.4 kΩ | 8 |
| LED dimming frequency | fDIM | 18163 | 19531 | 20899 | Hz | PWM_FSET = 124 kΩ | 8 |
| Switching Frequency | fSW | 93 | 100 | 107 | kHz | BST_FSET = 7.87 kΩ | 8 |
| Switching Frequency | fSW | 186 | 200 | 214 | kHz | BST_FSET = 4.75 kΩ | 8 |
| Switching Frequency | fSW | 281 | 303 | 325 | kHz | BST_FSET = 5.76 kΩ | 8 |
| Switching Frequency | fSW | 372 | 400 | 428 | kHz | BST_FSET = 3.92 kΩ | 8 |
| Switching Frequency | fSW | 465 | 500 | 535 | kHz | BST_FSET = 11 kΩ | 8 |
| Switching Frequency | fSW | 1690 | 1818 | 1946 | kHz | BST_FSET = 17.8 kΩ | 8 |
| Switching Frequency | fSW | 1860 | 2000 | 2140 | kHz | BST_FSET = 42.4 kΩ | 8 |
| Switching Frequency | fSW | 2066 | 2222 | 2378 | kHz | BST_FSET = 124 kΩ | 8 |
| External FET current limit | VISNS | 180 | 200 | 220 | mV | VISNS threshold, RSENSE= 15 to 50 mΩ | 8 |
| IDAC maximum current | ISEL_MAX | 36.4 | 38.7 | 40.2 | µA | VDD = 3.3 V | 8 |
| EN logic low threshold | VENIL | 0.4 | V | 9 | |||
| EN logic high threshold | VENIH | 1.2 | V | 9 | |||
| Logic low threshold | VIL | 0.4 | V | VDD = 3.3 V and 5 V | 9 | ||
| Logic high threshold | VIH | 1.2 | V | VDD = 3.3 V and 5 V | 9 | ||
| Output level low | VOL | 0.2 | 0.4 | V | I = 3 mA | 9 | |
| Output leakage current | ILEAKAGE | 1 | µA | V = 3.3 V | 9 | ||
| Clock frequency | fSCLK | 400 | kHz | 9 | |||
| Junction-to-ambient thermal resistance | RθJA | 32.9 | °C/W | QFN 32-pin | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 19.6 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 6.8 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.8 | °C/W | 6 | |||
| Voltage on VSENSE_P, FB, OUT1 to OUT4 | -0.3 | 52 | V | 5 | |||
| Voltage on C1N, C1P, VDD, EN, ISNS, ISNS_GND, INT, MODE, PWM_FSET, BST_FSET, LED_SET, ISET, GD, CPUMP | -0.3 | 6 | V | 5 | |||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Voltage on VSENSE_P, VSENSE_N, SD, UVLO | 3 | 12 | 48 | V | 5 | ||
| VDD voltage | VDD | 3 | 5.5 | V | NOM printed as 3.3/5 | 5 | |
| Ambient temperature | TA | -40 | 125 | °C | 5 |
CAD (KiCad official)
- Symbol:
TPS92390RHBR - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
tps92390rhbr-etched.step/tps92390rhbr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps92390rhbr.step/tps92390rhbr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (78 pp, sha256
c24eaa970042aaaf, retrieved 2026-10-31, tier: manufacturer) (maker link no longer resolves; copy stored with this page) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).