3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS7A8701RTJR
Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · QFN-20-EP(4x4)
TPS7A8701RTJR from Texas Instruments, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | power_in | Input supply pin for LDO 1 requiring 10 µF or greater input capacitor located as close as practical. |
| 2 | IN1 | power_in | Input supply pin for LDO 1 requiring 10 µF or greater input capacitor located as close as practical. |
| 3 | GND | power_in | Ground pin connected to thermal pad and each other with low-impedance connection. |
| 4 | IN2 | power_in | Input supply pin for LDO 2 requiring 10 µF or greater input capacitor located as close as practical. |
| 5 | IN2 | power_in | Input supply pin for LDO 2 requiring 10 µF or greater input capacitor located as close as practical. |
| 6 | EN2 | input | Enable pin for LDO 2; enables when VEN ≥ 1.1V, disables when VEN ≤ 0.4V; connect to IN2 if enable function not used. |
| 7 | NR/SS2 | passive | Noise-reduction and soft-start pin for LDO 2; capacitor value 10 nF to 10 µF recommended to reduce reference noise and enable soft-start function. |
| 8 | SS_CTRL2 | input | Soft-start control pin for LDO 2; connect to GND for typical soft-start or to VIN for fast charging of NR/SS capacitor. |
| 9 | PG2 | tri_state | Open-drain power-good indicator for LDO 2; requires 10 kΩ to 100 kΩ external pullup resistor; asserts when output ≥ 88.9% of target voltage. |
| 10 | FB2 | input | Feedback pin for LDO 2 error amplifier; 10 nF feed-forward capacitor from FB2 to OUT2 recommended to maximize AC performance. |
| 11 | OUT2 | output | Regulated output for LDO 2 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |
| 12 | OUT2 | output | Regulated output for LDO 2 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |
| 13 | GND | power_in | Ground pin connected to thermal pad and each other with low-impedance connection. |
| 14 | OUT1 | output | Regulated output for LDO 1 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |
| 15 | OUT1 | output | Regulated output for LDO 1 with range 0.8V to 5.2V; requires 10 µF or greater ceramic capacitor placed close to output. |
| 16 | FB1 | input | Feedback pin for LDO 1 error amplifier; 10 nF feed-forward capacitor from FB1 to OUT1 recommended to maximize AC performance. |
| 17 | PG1 | tri_state | Open-drain power-good indicator for LDO 1; requires 10 kΩ to 100 kΩ external pullup resistor; asserts when output ≥ 88.9% of target voltage. |
| 18 | SS_CTRL1 | input | Soft-start control pin for LDO 1; connect to GND for typical soft-start or to VIN for fast charging of NR/SS capacitor. |
| 19 | NR/SS1 | passive | Noise-reduction and soft-start pin for LDO 1; capacitor value 10 nF to 10 µF recommended to reduce reference noise and enable soft-start function. |
| 20 | EN1 | input | Enable pin for LDO 1; enables when VEN ≥ 1.1V, disables when VEN ≤ 0.4V; connect to IN1 if enable function not used. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-20-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| INx, PGx, ENx voltage | -0.3 | 7 | V | 4 | |||
| INx, PGx, ENx voltage (pulse) | -0.3 | 7.5 | V | 5% duty cycle, pulse duration = 200 µs | 4 | ||
| OUTx voltage | -0.3 | V | 4 | ||||
| SS_CTRLx voltage | -0.3 | V | 4 | ||||
| NR/SSx, FBx voltage | -0.3 | 3.6 | V | 4 | |||
| PGx sink current into device | 5 | mA | 4 | ||||
| Operating junction temperature | TJ | -55 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 4 | ||
| Electrostatic discharge, human body model (HBM) | V(ESD) | -2000 | 2000 | V | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 | 4 | |
| Electrostatic discharge, charged device model (CDM) | V(ESD) | -500 | 500 | V | Charged device model (CDM), per JEDEC specification JESD22-C101 | 4 | |
| Input supply voltage range | VINx | 1.4 | 6.5 | V | 4 | ||
| Output voltage range | VOUTx | 0.8 | 5.2 | V | 4 | ||
| Output current | IOUTx | 0 | 0.5 | A | 4 | ||
| Input capacitor, each input | CINx | 10 | µF | each input | 4 | ||
| Output capacitor | COUTx | 10 | µF | 4 | |||
| Noise-reduction capacitor | CNR/SSx | 1 | µF | 4 | |||
| Power-good pullup resistance | RPGx | 10 | 100 | kΩ | 4 | ||
| Junction temperature range | TJ | -40 | 125 | °C | 4 | ||
| Input supply UVLOx rising threshold | VUVLOx | 1.31 | 1.39 | V | VINx rising | 5 | |
| VOUTx accuracy | VOUTx | -1 | 1 | % | 0.8 V ≤ VOUTx ≤ 5.2 V, 5 mA ≤ IOUTx ≤ 0.5 A | 5 | |
| Dropout voltage | VDO | 100 | mV | 1.4 V ≤ VINx ≤ 5.3 V, IOUTx = 0.5 A, VFBx = 0.8 V – 3% | 5 | ||
| Output current limit | ILIM | 0.8 | 1.1 | 1.5 | A | VOUTx forced at 0.9 × VOUTx(TARGET) | 5 |
| GND pin current | IGND | 2.1 | 3.5 | mA | Both channels enabled, per channel, VINx = 6.5 V, IOUTx = 5 mA | 5 | |
| GND pin current | IGND | 4 | mA | Both channels enabled, per channel, VINx = 1.4 V, IOUTx = 0.5 A | 5 | ||
| Shutdown GND pin current | ISDN | 0.1 | 15 | µA | Both channels shutdown, per channel, PGx = (open), VINx = 6.5 V, VENx = 0.4 V | 5 | |
| ENx pin current | IENx | -0.2 | 0.2 | µA | VINx = 6.5 V, 0 V ≤ VENx ≤ 6.5 V | 5 | |
| ENx pin low-level input voltage | VIL(ENx) | 0 | 0.4 | V | device disabled | 5 | |
| ENx pin high-level input voltage | VIH(ENx) | 1.1 | 6.5 | V | device enabled | 5 | |
| SS_CTRLx pin current | ISS_CTRLx | -0.2 | 0.2 | µA | VINx = 6.5 V, 0 V ≤ VSS_CTRLx ≤ 6.5 V | 5 | |
| PGx pin threshold | VIT(PGx) | 82 | 88.9 | 93 | % | For PGx transitioning low with falling VOUTx, expressed as a percentage of VOUTx(TARGET) | 5 |
| PGx pin low-level output voltage | VOL(PGx) | 0.4 | V | VOUTx < VIT(PGx), IPGx = –1 mA (current into device) | 5 | ||
| PGx pin leakage current | Ilkg(PGx) | 1 | µA | VOUTx > VIT(PGx), VPGx = 6.5 V | 5 | ||
| NR/SSx pin charging current | INR/SSx | 4 | 6.2 | 9 | µA | VNR/SSx = GND, 1.4 V ≤ VINx ≤ 6.5 V, VSS_CTRLx = GND | 5 |
| NR/SSx pin charging current | INR/SSx | 65 | 100 | 150 | µA | VNR/SSx = GND, 1.4 V ≤ VINx ≤ 6.5 V, VSS_CTRLx = VINx | 5 |
| FBx pin leakage current | IFBx | -100 | 100 | nA | VINx = 6.5 V, VFBx = 0.8 V | 5 | |
| Junction-to-ambient thermal resistance | RθJA | 33 | °C/W | 4 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 26.8 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 8 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 0.3 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 8 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 2.4 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
TPS7A8701RTJR - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
tps7a8701rtjr-etched.step/tps7a8701rtjr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps7a8701rtjr.step/tps7a8701rtjr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (48 pp, sha256
00030644bd522fb5, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).