main
Ray
Publish 0.1.0
d22e5c1
TPS7A1901DRBT
Texas Instruments · Linear Voltage Regulators (LDO) · WSON-8-EP(3x3)
TPS7A1901DRBT from Texas Instruments, in a WSON-8-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DELAY | passive | Delay pin: connect a capacitor to GND to set the PG delay time, or leave open for the default 325 µs typical delay if PG is not needed. |
| 2 | OUT | output | Regulator output: when VOUT is above 2.5 V, use a 10 µF to 500 µF ceramic capacitor with ESR from 0.001 Ω to 20 Ω; when VOUT is 1.5 V to 2.5 V, the minimum stable capacitor is 22 µF. |
| 3 | FB | input | Feedback pin: input to the control-loop error amplifier, with VFB of 1.233 V typical (1.208 V to 1.258 V). |
| 4 | GND | power_in | Ground pin; connect the output capacitor ground directly to this pin and keep the VIN and VOUT ground planes joined only here. |
| 5 | GND | power_in | Ground pin; connect the output capacitor ground directly to this pin and keep the VIN and VOUT ground planes joined only here. |
| 6 | EN | input | Enable pin: VEN ≥ 1.7 V enables the regulator and VEN ≤ 0.4 V disables it, with VEN rated 0 V to 40 V; it can be tied to IN if unused. |
| 7 | IN | power_in | Regulator input supply pin, operating from 4 V to 40 V. |
| 8 | PG | output | Power-good open-drain output: connect to VOUT through an external resistor; it is pulled low when VOUT falls below the threshold (89.6% of VOUT, typical deglitch 180 µs). |
| 9 | Thermal pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-8-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage IN, EN (absolute maximum) | -0.3 | 45 | V | 4 | |||
| Output OUT (absolute maximum) | -0.3 | V | Max is VIN + 0.3 V or 22 V, whichever is lower | 4 | |||
| DELAY (absolute maximum) | -0.3 | 45 | V | 4 | |||
| FB, PG (absolute maximum) | -0.3 | 22 | V | 4 | |||
| Operating junction temperature (absolute maximum) | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature (absolute maximum) | Tstg | -65 | 150 | °C | 4 | ||
| Input supply voltage (recommended) | VIN | 4 | 40 | V | 4 | ||
| Output voltage (recommended) | VOUT | 1.5 | 18 | V | 4 | ||
| Enable voltage (recommended) | VEN | 0 | 40 | V | 4 | ||
| Operating junction temperature (recommended) | TJ | -40 | 125 | °C | 4 | ||
| Input voltage | VIN | 4 | 40 | V | VOUT ≤ 3.5 V, IOUT = 0 mA to 450 mA | 5 | |
| Input voltage | VIN | 40 | V | VOUT ≥ 3.5 V, IOUT = 0 mA to 450 mA; min is VOUT + 0.5 V | 5 | ||
| Quiescent current | IQ | 15 | 25 | µA | VIN = 4 V to 40 V, VOUT = 1.5 V, VEN = 5 V, IOUT = 0.2 mA | 5 | |
| Quiescent current | IQ | 25 | 40 | µA | VIN = 18.5 V to 40 V, VOUT = 18 V, VEN = 5 V, IOUT = 0.2 mA | 5 | |
| Shutdown current | ISHDN | 4 | µA | VEN = 0 V, IOUT = 0 mA, VIN = 18 V, VOUT = 1.5 V | 5 | ||
| Feedback voltage | VFB | 1.208 | 1.233 | 1.258 | V | Reference voltage for FB pin | 5 |
| Undervoltage lockout | VIN_UVLO | 2.6 | V | Ramp VIN down until output is turned off | 5 | ||
| Undervoltage detection hysteresis | UVLOHys | 1 | V | VIN rising | 5 | ||
| Logic input low level | VEN_LO | 0 | 0.4 | V | 5 | ||
| Logic input high level | VEN_HI | 1.7 | V | 5 | |||
| EN pin current | IEN | 1 | µA | VEN = 40 V, VIN = 14 V | 5 | ||
| Regulated output | VOUT | -2 | 2 | % | VIN = VOUT + 1 V to 40 V and VIN ≥ 4 V, IOUT = 100 µA to 450 mA | 5 | |
| Line regulation | ΔVO(ΔVI) | 10 | mV | VIN = VOUT + 1 V to 40 V and VIN ≥ 4 V, IOUT = 100 mA | 5 | ||
| Load regulation | ΔVO(ΔIL) | 10 | mV | IOUT = 1 mA to 450 mA, VIN = VOUT + 1 V and VIN ≥ 4 V | 5 | ||
| Dropout voltage | VDO | 240 | 450 | mV | VIN, VOUT, IOUT = 400 mA | 5 | |
| Dropout voltage | VDO | 160 | 300 | mV | VIN, VOUT, IOUT = 200 mA | 5 | |
| Output current | IOUT | 0 | 450 | mA | VOUT in regulation | 5 | |
| Output current-limit | ICL | 140 | 360 | mA | VOUT short to ground | 5 | |
| Output current-limit | ICL | 470 | 850 | mA | VOUT = VOUT nominal × 0.9 | 5 | |
| Power-supply ripple rejection | PSRR | 60 | dB | IOUT = 100 mA, COUT = 22 µF, f = 100 Hz | 5 | ||
| Power-supply ripple rejection | PSRR | 40 | dB | IOUT = 100 mA, COUT = 22 µF, f = 100 kHz | 5 | ||
| PG output low voltage | VOL | 0.4 | V | IOL = 0.5 mA | 5 | ||
| PG leakage current | IOH | 1 | µA | PG pulled to VOUT with 10-kΩ resistor | 5 | ||
| Power good threshold | VT(PG) | 89.6 | 91.6 | 93.6 | % of VOUT | VOUT power-up | 5 |
| Power good hysteresis | Vhys | 2 | % of VOUT | VOUT power-down | 5 | ||
| Delay capacitor charging current | IDelay | 5 | 9.5 | 14 | µA | 5 | |
| Delay pin comparator threshold voltage | VT(PG_DLY) | 1 | V | 5 | |||
| Junction shutdown temperature | Tsd | 175 | °C | Temperature increasing | 5 | ||
| Hysteresis of thermal shutdown | Thys | 24 | °C | 5 | |||
| Junction-to-ambient thermal resistance | RθJA | 48 | °C/W | 4 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 56.3 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 22.4 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 0.9 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 22.5 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.6 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
TPS7A1901DRBT - Footprint:
Package_SON:WSON-8-1EP_3x3mm_P0.5mm_EP1.6x2.0mm - 3D model: WSON-8-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps7a1901drbt-etched.step/tps7a1901drbt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps7a1901drbt.step/tps7a1901drbt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (24 pp, sha256
f33510ddb20b0b1d, retrieved 2026-10-28, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS7A1901DRBT
**Texas Instruments** · Linear Voltage Regulators (LDO) · WSON-8-EP(3x3)
TPS7A1901DRBT from Texas Instruments, in a WSON-8-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DELAY | passive | Delay pin: connect a capacitor to GND to set the PG delay time, or leave open for the default 325 µs typical delay if PG is not needed. |
| 2 | OUT | output | Regulator output: when VOUT is above 2.5 V, use a 10 µF to 500 µF ceramic capacitor with ESR from 0.001 Ω to 20 Ω; when VOUT is 1.5 V to 2.5 V, the minimum stable capacitor is 22 µF. |
| 3 | FB | input | Feedback pin: input to the control-loop error amplifier, with VFB of 1.233 V typical (1.208 V to 1.258 V). |
| 4 | GND | power_in | Ground pin; connect the output capacitor ground directly to this pin and keep the VIN and VOUT ground planes joined only here. |
| 5 | GND | power_in | Ground pin; connect the output capacitor ground directly to this pin and keep the VIN and VOUT ground planes joined only here. |
| 6 | EN | input | Enable pin: VEN ≥ 1.7 V enables the regulator and VEN ≤ 0.4 V disables it, with VEN rated 0 V to 40 V; it can be tied to IN if unused. |
| 7 | IN | power_in | Regulator input supply pin, operating from 4 V to 40 V. |
| 8 | PG | output | Power-good open-drain output: connect to VOUT through an external resistor; it is pulled low when VOUT falls below the threshold (89.6% of VOUT, typical deglitch 180 µs). |
| 9 | Thermal pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-8-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage IN, EN (absolute maximum) | | -0.3 | | 45 | V | | 4 |
| Output OUT (absolute maximum) | | -0.3 | | | V | Max is VIN + 0.3 V or 22 V, whichever is lower | 4 |
| DELAY (absolute maximum) | | -0.3 | | 45 | V | | 4 |
| FB, PG (absolute maximum) | | -0.3 | | 22 | V | | 4 |
| Operating junction temperature (absolute maximum) | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature (absolute maximum) | Tstg | -65 | | 150 | °C | | 4 |
| Input supply voltage (recommended) | VIN | 4 | | 40 | V | | 4 |
| Output voltage (recommended) | VOUT | 1.5 | | 18 | V | | 4 |
| Enable voltage (recommended) | VEN | 0 | | 40 | V | | 4 |
| Operating junction temperature (recommended) | TJ | -40 | | 125 | °C | | 4 |
| Input voltage | VIN | 4 | | 40 | V | VOUT ≤ 3.5 V, IOUT = 0 mA to 450 mA | 5 |
| Input voltage | VIN | | | 40 | V | VOUT ≥ 3.5 V, IOUT = 0 mA to 450 mA; min is VOUT + 0.5 V | 5 |
| Quiescent current | IQ | | 15 | 25 | µA | VIN = 4 V to 40 V, VOUT = 1.5 V, VEN = 5 V, IOUT = 0.2 mA | 5 |
| Quiescent current | IQ | | 25 | 40 | µA | VIN = 18.5 V to 40 V, VOUT = 18 V, VEN = 5 V, IOUT = 0.2 mA | 5 |
| Shutdown current | ISHDN | | 4 | | µA | VEN = 0 V, IOUT = 0 mA, VIN = 18 V, VOUT = 1.5 V | 5 |
| Feedback voltage | VFB | 1.208 | 1.233 | 1.258 | V | Reference voltage for FB pin | 5 |
| Undervoltage lockout | VIN_UVLO | | 2.6 | | V | Ramp VIN down until output is turned off | 5 |
| Undervoltage detection hysteresis | UVLOHys | | 1 | | V | VIN rising | 5 |
| Logic input low level | VEN_LO | 0 | | 0.4 | V | | 5 |
| Logic input high level | VEN_HI | | | 1.7 | V | | 5 |
| EN pin current | IEN | | 1 | | µA | VEN = 40 V, VIN = 14 V | 5 |
| Regulated output | VOUT | -2 | | 2 | % | VIN = VOUT + 1 V to 40 V and VIN ≥ 4 V, IOUT = 100 µA to 450 mA | 5 |
| Line regulation | ΔVO(ΔVI) | | 10 | | mV | VIN = VOUT + 1 V to 40 V and VIN ≥ 4 V, IOUT = 100 mA | 5 |
| Load regulation | ΔVO(ΔIL) | | 10 | | mV | IOUT = 1 mA to 450 mA, VIN = VOUT + 1 V and VIN ≥ 4 V | 5 |
| Dropout voltage | VDO | | 240 | 450 | mV | VIN, VOUT, IOUT = 400 mA | 5 |
| Dropout voltage | VDO | | 160 | 300 | mV | VIN, VOUT, IOUT = 200 mA | 5 |
| Output current | IOUT | 0 | | 450 | mA | VOUT in regulation | 5 |
| Output current-limit | ICL | 140 | | 360 | mA | VOUT short to ground | 5 |
| Output current-limit | ICL | 470 | | 850 | mA | VOUT = VOUT nominal × 0.9 | 5 |
| Power-supply ripple rejection | PSRR | | 60 | | dB | IOUT = 100 mA, COUT = 22 µF, f = 100 Hz | 5 |
| Power-supply ripple rejection | PSRR | | 40 | | dB | IOUT = 100 mA, COUT = 22 µF, f = 100 kHz | 5 |
| PG output low voltage | VOL | | 0.4 | | V | IOL = 0.5 mA | 5 |
| PG leakage current | IOH | | 1 | | µA | PG pulled to VOUT with 10-kΩ resistor | 5 |
| Power good threshold | VT(PG) | 89.6 | 91.6 | 93.6 | % of VOUT | VOUT power-up | 5 |
| Power good hysteresis | Vhys | | 2 | | % of VOUT | VOUT power-down | 5 |
| Delay capacitor charging current | IDelay | 5 | 9.5 | 14 | µA | | 5 |
| Delay pin comparator threshold voltage | VT(PG_DLY) | | 1 | | V | | 5 |
| Junction shutdown temperature | Tsd | | 175 | | °C | Temperature increasing | 5 |
| Hysteresis of thermal shutdown | Thys | | 24 | | °C | | 5 |
| Junction-to-ambient thermal resistance | RθJA | | 48 | | °C/W | | 4 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 56.3 | | °C/W | | 4 |
| Junction-to-board thermal resistance | RθJB | | 22.4 | | °C/W | | 4 |
| Junction-to-top characterization parameter | ψJT | | 0.9 | | °C/W | | 4 |
| Junction-to-board characterization parameter | ψJB | | 22.5 | | °C/W | | 4 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 4.6 | | °C/W | | 4 |
## CAD (KiCad official)
- Symbol: `TPS7A1901DRBT`
- Footprint: `Package_SON:WSON-8-1EP_3x3mm_P0.5mm_EP1.6x2.0mm`
- 3D model: WSON-8-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `tps7a1901drbt-etched.step` / `tps7a1901drbt-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps7a1901drbt.step` / `tps7a1901drbt.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps7a19) (24 pp, sha256 `f33510ddb20b0b1d`, retrieved 2026-10-28, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps7a1901drbt-datasheet.pdf)