main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers tps7a1901drbt: viewers · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
tps7a1901drbt-etched.glb Publish 0.1.0 · Ray
tps7a1901drbt-etched.step tps7a1901drbt: factory component page (tier=mfr) · Ray
tps7a1901drbt-hero.glb tps7a1901drbt: hero GLB from the etched model (keeps the MPN mark) · Ray
tps7a1901drbt-hero.overlay.json Publish 0.1.0 · Ray
tps7a1901drbt.glb Publish 0.1.0 · Ray
tps7a1901drbt.kicad_mod Publish 0.1.0 · Ray
tps7a1901drbt.kicad_sym Publish 0.1.0 · Ray
tps7a1901drbt.lbr Publish 0.1.0 · Ray
tps7a1901drbt.step Publish 0.1.0 · Ray

TPS7A1901DRBT

Texas Instruments · Linear Voltage Regulators (LDO) · WSON-8-EP(3x3)

TPS7A1901DRBT from Texas Instruments, in a WSON-8-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DELAY passive Delay pin: connect a capacitor to GND to set the PG delay time, or leave open for the default 325 µs typical delay if PG is not needed.
2 OUT output Regulator output: when VOUT is above 2.5 V, use a 10 µF to 500 µF ceramic capacitor with ESR from 0.001 Ω to 20 Ω; when VOUT is 1.5 V to 2.5 V, the minimum stable capacitor is 22 µF.
3 FB input Feedback pin: input to the control-loop error amplifier, with VFB of 1.233 V typical (1.208 V to 1.258 V).
4 GND power_in Ground pin; connect the output capacitor ground directly to this pin and keep the VIN and VOUT ground planes joined only here.
5 GND power_in Ground pin; connect the output capacitor ground directly to this pin and keep the VIN and VOUT ground planes joined only here.
6 EN input Enable pin: VEN ≥ 1.7 V enables the regulator and VEN ≤ 0.4 V disables it, with VEN rated 0 V to 40 V; it can be tied to IN if unused.
7 IN power_in Regulator input supply pin, operating from 4 V to 40 V.
8 PG output Power-good open-drain output: connect to VOUT through an external resistor; it is pulled low when VOUT falls below the threshold (89.6% of VOUT, typical deglitch 180 µs).
9 Thermal pad passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-8-EP(3x3)
Category Power Supply Chip
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage IN, EN (absolute maximum) -0.3 45 V 4
Output OUT (absolute maximum) -0.3 V Max is VIN + 0.3 V or 22 V, whichever is lower 4
DELAY (absolute maximum) -0.3 45 V 4
FB, PG (absolute maximum) -0.3 22 V 4
Operating junction temperature (absolute maximum) TJ -40 150 °C 4
Storage temperature (absolute maximum) Tstg -65 150 °C 4
Input supply voltage (recommended) VIN 4 40 V 4
Output voltage (recommended) VOUT 1.5 18 V 4
Enable voltage (recommended) VEN 0 40 V 4
Operating junction temperature (recommended) TJ -40 125 °C 4
Input voltage VIN 4 40 V VOUT ≤ 3.5 V, IOUT = 0 mA to 450 mA 5
Input voltage VIN 40 V VOUT ≥ 3.5 V, IOUT = 0 mA to 450 mA; min is VOUT + 0.5 V 5
Quiescent current IQ 15 25 µA VIN = 4 V to 40 V, VOUT = 1.5 V, VEN = 5 V, IOUT = 0.2 mA 5
Quiescent current IQ 25 40 µA VIN = 18.5 V to 40 V, VOUT = 18 V, VEN = 5 V, IOUT = 0.2 mA 5
Shutdown current ISHDN 4 µA VEN = 0 V, IOUT = 0 mA, VIN = 18 V, VOUT = 1.5 V 5
Feedback voltage VFB 1.208 1.233 1.258 V Reference voltage for FB pin 5
Undervoltage lockout VIN_UVLO 2.6 V Ramp VIN down until output is turned off 5
Undervoltage detection hysteresis UVLOHys 1 V VIN rising 5
Logic input low level VEN_LO 0 0.4 V 5
Logic input high level VEN_HI 1.7 V 5
EN pin current IEN 1 µA VEN = 40 V, VIN = 14 V 5
Regulated output VOUT -2 2 % VIN = VOUT + 1 V to 40 V and VIN ≥ 4 V, IOUT = 100 µA to 450 mA 5
Line regulation ΔVO(ΔVI) 10 mV VIN = VOUT + 1 V to 40 V and VIN ≥ 4 V, IOUT = 100 mA 5
Load regulation ΔVO(ΔIL) 10 mV IOUT = 1 mA to 450 mA, VIN = VOUT + 1 V and VIN ≥ 4 V 5
Dropout voltage VDO 240 450 mV VIN, VOUT, IOUT = 400 mA 5
Dropout voltage VDO 160 300 mV VIN, VOUT, IOUT = 200 mA 5
Output current IOUT 0 450 mA VOUT in regulation 5
Output current-limit ICL 140 360 mA VOUT short to ground 5
Output current-limit ICL 470 850 mA VOUT = VOUT nominal × 0.9 5
Power-supply ripple rejection PSRR 60 dB IOUT = 100 mA, COUT = 22 µF, f = 100 Hz 5
Power-supply ripple rejection PSRR 40 dB IOUT = 100 mA, COUT = 22 µF, f = 100 kHz 5
PG output low voltage VOL 0.4 V IOL = 0.5 mA 5
PG leakage current IOH 1 µA PG pulled to VOUT with 10-kΩ resistor 5
Power good threshold VT(PG) 89.6 91.6 93.6 % of VOUT VOUT power-up 5
Power good hysteresis Vhys 2 % of VOUT VOUT power-down 5
Delay capacitor charging current IDelay 5 9.5 14 µA 5
Delay pin comparator threshold voltage VT(PG_DLY) 1 V 5
Junction shutdown temperature Tsd 175 °C Temperature increasing 5
Hysteresis of thermal shutdown Thys 24 °C 5
Junction-to-ambient thermal resistance RθJA 48 °C/W 4
Junction-to-case (top) thermal resistance RθJC(top) 56.3 °C/W 4
Junction-to-board thermal resistance RθJB 22.4 °C/W 4
Junction-to-top characterization parameter ψJT 0.9 °C/W 4
Junction-to-board characterization parameter ψJB 22.5 °C/W 4
Junction-to-case (bottom) thermal resistance RθJC(bot) 4.6 °C/W 4

CAD (KiCad official)

  • Symbol: TPS7A1901DRBT
  • Footprint: Package_SON:WSON-8-1EP_3x3mm_P0.5mm_EP1.6x2.0mm
  • 3D model: WSON-8-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: tps7a1901drbt-etched.step / tps7a1901drbt-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps7a1901drbt.step / tps7a1901drbt.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (24 pp, sha256 f33510ddb20b0b1d, retrieved 2026-10-28, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF