main
Ray
Publish 0.1.0
0ce221a
TPS75215QPWPR
Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · HTSSOP-20-EP
TPS75215QPWPR from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 2 | NC | unconnected | Not connected. |
| 3 | IN | power_in | Input voltage terminal with a recommended range of 2.7 V to 5.5 V, bypassed with a 0.22 µF to 1 µF capacitor placed as close to the input pins as possible. |
| 4 | IN | power_in | Input voltage terminal with a recommended range of 2.7 V to 5.5 V, bypassed with a 0.22 µF to 1 µF capacitor placed as close to the input pins as possible. |
| 5 | EN | input | Negative-polarity enable input: a logic low (VEN(LO) at most 0.7 V) enables the device and a logic high (VEN(HI) at least 2 V) shuts it down. |
| 6 | RESET | output | Open-drain, active-low reset output (TPS752xxQ) that goes high-impedance after a 100 ms delay when VOUT reaches 95% of its regulated value and requires an external pullup resistor. |
| 7 | FB/SENSE | input | Sense input for fixed-output options that must be connected to the regulator output as short as possible, with RC filtering not recommended because it may cause oscillation. |
| 8 | OUTPUT | power_out | Regulated output voltage that requires an output capacitor of at least 47 µF with ESR between 100 mΩ and 10 Ω connected to GND. |
| 9 | OUTPUT | power_out | Regulated output voltage that requires an output capacitor of at least 47 µF with ESR between 100 mΩ and 10 Ω connected to GND. |
| 10 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 11 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 12 | NC | unconnected | Not connected. |
| 13 | NC | unconnected | Not connected. |
| 14 | NC | unconnected | Not connected. |
| 15 | NC | unconnected | Not connected. |
| 16 | NC | unconnected | Not connected. |
| 17 | GND | power_in | Ground terminal of the regulator. |
| 18 | NC | unconnected | Not connected. |
| 19 | NC | unconnected | Not connected. |
| 20 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Power Management (PMIC) |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | VIN | -0.3 | 6 | V | 2 | ||
| Voltage range at EN | -0.3 | 16.5 | V | 2 | |||
| Maximum RESET voltage (TPS752xxQ) | 16.5 | V | 2 | ||||
| Output voltage range at OUT, FB | 5.5 | V | 2 | ||||
| Operating virtual junction temperature range | TJ | -40 | 125 | °C | 2 | ||
| Storage junction temperature range | TSTG | -65 | 150 | °C | 2 | ||
| Input voltage range | VIN | 2.7 | 5.5 | V | 3 | ||
| Output voltage range | VOUT | 1.5 | 5 | V | 3 | ||
| Output current | IOUT | 0 | 2 | A | 3 | ||
| Operating virtual junction temperature | TJ | -40 | 125 | °C | 3 | ||
| 1.5 V output voltage | VOUT | 1.47 | 1.5 | 1.53 | V | 2.7 V < VIN < 5.5 V | 4 |
| Ground pin current | IGND | 75 | 125 | μA | IOUT = 1 mA to 2 A | 4 | |
| Output voltage line regulation | ΔVOUT%/VOUT | 0.01 | 0.1 | %/V | VOUT + 1 V < VIN ≤ 5 V | 4 | |
| Standby current | ISTBY | 1 | 10 | μA | EN = VIN | 4 | |
| Output current limit | ICL | 3.3 | 4.5 | A | VOUT = 0 V | 4 | |
| High-level enable input voltage | VEN(HI) | 2 | V | 4 | |||
| Low-level enable input voltage | VEN(LO) | 0.7 | V | 4 | |||
| Input current (EN) | -1 | 1 | μA | EN = VIN | 4 | ||
| Input current (EN) | -1 | 0 | 1 | μA | EN = 0 V | 4 | |
| Minimum input voltage for valid RESET | VRESET | 1 | 1.3 | V | IOUT(RESET) = 300 μA, V(RESET) ≤ 0.8 V | 4 | |
| RESET trip threshold voltage | 92 | 98 | %VOUT | VOUT decreasing | 4 | ||
| RESET output low voltage | 0.15 | 0.4 | V | VIN = 2.7 V, IOUT(RESET) = 1 mA | 4 | ||
| Thermal resistance junction-to-ambient (PWP, text) | RθJA | 34.6 | °C/W | 20-terminal PWP, no airflow (stated in text) | 18 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | Exposed pad mounting 63/67 tin/lead (Sn/Pb) solder Heatsink Area | 21 |
CAD (KiCad official)
- Symbol:
TPS75215QPWPR - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm tall, family nominal (no datasheet A read)). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
tps75215qpwpr-etched.step/tps75215qpwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps75215qpwpr.step/tps75215qpwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (33 pp, sha256
ddac75f3b3fd04bf, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS75215QPWPR
**Texas Instruments** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · HTSSOP-20-EP
TPS75215QPWPR from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 2 | NC | unconnected | Not connected. |
| 3 | IN | power_in | Input voltage terminal with a recommended range of 2.7 V to 5.5 V, bypassed with a 0.22 µF to 1 µF capacitor placed as close to the input pins as possible. |
| 4 | IN | power_in | Input voltage terminal with a recommended range of 2.7 V to 5.5 V, bypassed with a 0.22 µF to 1 µF capacitor placed as close to the input pins as possible. |
| 5 | EN | input | Negative-polarity enable input: a logic low (VEN(LO) at most 0.7 V) enables the device and a logic high (VEN(HI) at least 2 V) shuts it down. |
| 6 | RESET | output | Open-drain, active-low reset output (TPS752xxQ) that goes high-impedance after a 100 ms delay when VOUT reaches 95% of its regulated value and requires an external pullup resistor. |
| 7 | FB/SENSE | input | Sense input for fixed-output options that must be connected to the regulator output as short as possible, with RC filtering not recommended because it may cause oscillation. |
| 8 | OUTPUT | power_out | Regulated output voltage that requires an output capacitor of at least 47 µF with ESR between 100 mΩ and 10 Ω connected to GND. |
| 9 | OUTPUT | power_out | Regulated output voltage that requires an output capacitor of at least 47 µF with ESR between 100 mΩ and 10 Ω connected to GND. |
| 10 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 11 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 12 | NC | unconnected | Not connected. |
| 13 | NC | unconnected | Not connected. |
| 14 | NC | unconnected | Not connected. |
| 15 | NC | unconnected | Not connected. |
| 16 | NC | unconnected | Not connected. |
| 17 | GND | power_in | Ground terminal of the regulator. |
| 18 | NC | unconnected | Not connected. |
| 19 | NC | unconnected | Not connected. |
| 20 | GND/HEATSINK | power_in | Ground/heatsink terminal that is internally connected to the thermal pad and IC substrate and may be connected to GND or left floating. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Power Management (PMIC) |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | VIN | -0.3 | | 6 | V | | 2 |
| Voltage range at EN | | -0.3 | | 16.5 | V | | 2 |
| Maximum RESET voltage (TPS752xxQ) | | | | 16.5 | V | | 2 |
| Output voltage range at OUT, FB | | | | 5.5 | V | | 2 |
| Operating virtual junction temperature range | TJ | -40 | | 125 | °C | | 2 |
| Storage junction temperature range | TSTG | -65 | | 150 | °C | | 2 |
| Input voltage range | VIN | 2.7 | | 5.5 | V | | 3 |
| Output voltage range | VOUT | 1.5 | | 5 | V | | 3 |
| Output current | IOUT | 0 | | 2 | A | | 3 |
| Operating virtual junction temperature | TJ | -40 | | 125 | °C | | 3 |
| 1.5 V output voltage | VOUT | 1.47 | 1.5 | 1.53 | V | 2.7 V < VIN < 5.5 V | 4 |
| Ground pin current | IGND | | 75 | 125 | μA | IOUT = 1 mA to 2 A | 4 |
| Output voltage line regulation | ΔVOUT%/VOUT | | 0.01 | 0.1 | %/V | VOUT + 1 V < VIN ≤ 5 V | 4 |
| Standby current | ISTBY | | 1 | 10 | μA | EN = VIN | 4 |
| Output current limit | ICL | | 3.3 | 4.5 | A | VOUT = 0 V | 4 |
| High-level enable input voltage | VEN(HI) | 2 | | | V | | 4 |
| Low-level enable input voltage | VEN(LO) | | | 0.7 | V | | 4 |
| Input current (EN) | | -1 | | 1 | μA | EN = VIN | 4 |
| Input current (EN) | | -1 | 0 | 1 | μA | EN = 0 V | 4 |
| Minimum input voltage for valid RESET | VRESET | | 1 | 1.3 | V | IOUT(RESET) = 300 μA, V(RESET) ≤ 0.8 V | 4 |
| RESET trip threshold voltage | | 92 | | 98 | %VOUT | VOUT decreasing | 4 |
| RESET output low voltage | | | 0.15 | 0.4 | V | VIN = 2.7 V, IOUT(RESET) = 1 mA | 4 |
| Thermal resistance junction-to-ambient (PWP, text) | RθJA | | 34.6 | | °C/W | 20-terminal PWP, no airflow (stated in text) | 18 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | Exposed pad mounting 63/67 tin/lead (Sn/Pb) solder Heatsink Area | 21 |
## CAD (KiCad official)
- Symbol: `TPS75215QPWPR`
- Footprint: `Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm`
- 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm tall, family nominal (no datasheet A read)). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `tps75215qpwpr-etched.step` / `tps75215qpwpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps75215qpwpr.step` / `tps75215qpwpr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps752.pdf) (33 pp, sha256 `ddac75f3b3fd04bf`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps75215qpwpr-datasheet.pdf)