component
TPS65563ARGTR
Public Made by Adomby adom
Texas Instruments Power Management - Specialized, TQFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS65563ARGTR
Texas Instruments · Power Management - Specialized · TQFN-16-EP(3x3)
TPS65563ARGTR from Texas Instruments, in a TQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Primary-side power MOSFET switch output; connect to the switched side of the transformer. |
| 2 | SW | output | Primary-side power MOSFET switch output; connect to the switched side of the transformer. |
| 3 | VBAT | power_in | Battery voltage input for MOSFET OFF timing detection; input range 1.4 V to 12 V with 10-µF bypass capacitor to GND. |
| 4 | I_PEAK | input | Primary-side peak current control input; voltage at I_PEAK sets the peak current threshold into SW. |
| 5 | GND | power_in | Ground for power and IC internal circuits; connect to ground plane. |
| 6 | CHG | input | Charge enable/disable input; drive high to start charging output capacitor, low to terminate charging. |
| 7 | F_ON | input | Flash on/off input; high enables xenon flash if F_EN is high, low disables flash. |
| 8 | F_EN | input | Flash acceptable input; high permits xenon flash with F_ON high, low forces flash disable. |
| 9 | XFULL | tri_state | Charge completion indicator open-drain output; pulls low when output fully charged, high impedance during charging and fault conditions. |
| 10 | VCC | power_in | Power supply input for gate driver and IC; voltage range 2.7 V to 5.5 V with 1-µF bypass capacitor to GND. |
| 11 | IGBT_VCC | power_out | Power supply output for IGBT driver block. |
| 12 | G_IGBT_P | output | IGBT gate driver output for turn-on; output swings from GND to IGBT_VCC to drive external IGBT devices with external resistor. |
| 13 | G_IGBT_N | output | IGBT gate driver output for turn-off; output swings from IGBT_VCC to GND to drive external IGBT devices with external resistor. |
| 14 | GND | power_in | Ground for power and IC internal circuits; connect to ground plane. |
| 15 | GND | power_in | Ground for power and IC internal circuits; connect to ground plane. |
| 16 | TEST_GND | power_in | Test ground used by TI for manufacturing; should be connected to GND and ground plane. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFN-16-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
CAD (KiCad official)
- Symbol:
TPS65563ARGTR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: TQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps65563argtr-etched.step/tps65563argtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps65563argtr.step/tps65563argtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (19 pp, sha256
59ee3fba0d7dece2, retrieved 2026-09-26, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).