main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs tps65283rger: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers tps65283rger: viewers · Ray
package.json tps65283rger: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json tps65283rger: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/tps65283rger · Ray
tps65283rger-etched.fit.json tps65283rger: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps65283rger-etched.glb tps65283rger: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps65283rger-etched.step tps65283rger: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps65283rger.glb Publish 0.1.0 · Ray
tps65283rger.kicad_mod Publish 0.1.0 · Ray
tps65283rger.kicad_sym Publish 0.1.0 · Ray
tps65283rger.lbr Publish 0.1.0 · Ray
tps65283rger.step Publish 0.1.0 · Ray

TPS65283RGER

Texas Instruments · DC-DC Converters · VQFN-24-EP(4x4)

TPS65283RGER from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PGOOD2 output Power good indicator for buck2; asserts low when output voltage is out of regulation due to thermal shutdown, dropout, overvoltage, disabled, or during soft start.
2 EN1 input Enable pin for buck1; high signal enables converter, optional ceramic capacitor provides delayed startup.
3 EN2 input Enable pin for buck2; high signal enables converter, optional ceramic capacitor provides delayed startup.
4 ROSC/SYNC input Programmable oscillator frequency from 200 kHz to 2 MHz via external resistor or external clock synchronization input.
5 SW_EN input Enable input for power switch; float to enable.
6 nFAULT output Active-low open-drain output; asserted low during power switch overcurrent or reverse-voltage condition.
7 SW_OUT power_out Power switch output node.
8 SW_IN power_in Power switch input node; input voltage range 2.4 V to 6 V.
9 VIN2 power_in Input power supply for buck2; connect with 10 µF ceramic capacitor as close as possible to pin.
10 PGND2 power_in Power ground connection for buck2; connect as close as possible to negative terminal of input capacitor.
11 LX2 output Switching node for buck2; voltage swings from diode drop below ground to buck2 input voltage.
12 BST2 passive Bootstrap supply for buck2 high-side gate driver; connect 47 nF ceramic capacitor from this pin to LX2.
13 COMP2 output Error amplifier output and compensation pin for buck2; connect series resistor and capacitor for control loop compensation.
14 FB2 input Feedback sensing pin for buck2 output voltage; feedback reference voltage 0.6 V ±1%, connect to resistor divider network.
15 RSET input Power switch current limit programming pin; external resistor sets current limit threshold, recommended range 9.1 kΩ to 80.6 kΩ.
16 AGND power_in Analog ground common to buck and power switch controllers; route separately from power grounds to V7V bypass capacitor negative terminal.
17 FB1 input Feedback sensing pin for buck1 output voltage; feedback reference voltage 0.6 V ±1%, connect to resistor divider network.
18 COMP1 output Error amplifier output and compensation pin for buck1; connect series resistor and capacitor for control loop compensation.
19 BST1 passive Bootstrap supply for buck1 high-side gate driver; connect 47 nF ceramic capacitor from this pin to LX1.
20 LX1 output Switching node for buck1; voltage swings from diode drop below ground to buck1 input voltage.
21 PGND1 power_in Power ground connection for buck1; connect as close as possible to negative terminal of input capacitor.
22 VIN1 power_in Input power supply for buck1 and internal analog bias circuits; connect with 10 µF ceramic capacitor as close as possible to pin.
23 V7V power_out Internal linear regulator output at typical 6.3 V for gate drivers and internal circuits; minimum 1 µF ceramic capacitor required for decoupling.
24 PGOOD1 output Power good indicator for buck1; asserts low when output voltage is out of regulation due to thermal shutdown, dropout, overvoltage, disabled, or during soft start.
25 PowerPAD power_in Exposed thermal pad underneath IC package; connect to power ground with multiple vias for thermal dissipation, no internal signal connection.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-24-EP(4x4)
Category Power Management (PMIC)
Pins 25

CAD (KiCad official)

  • Symbol: TPS65283RGER
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm
  • 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: tps65283rger-etched.step / tps65283rger-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps65283rger.step / tps65283rger.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (43 pp, sha256 eb69c587d9ca6697, retrieved 2026-09-25, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF