main
Ray tps65261rhbr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) a33cacf
{
  "schema_version": 1,
  "type": "component",
  "slug": "tps65261rhbr",
  "title": "TPS65261RHBR",
  "brief": "Texas Instruments DC-DC Converters, VQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.1.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "power management (pmic)",
    "tps65261rhbr",
    "factory-2.0.0",
    "extractor-text"
  ],
  "component": {
    "mpn": "TPS65261RHBR",
    "manufacturer": "Texas Instruments",
    "package": "VQFN-32-EP(5x5)",
    "pin_count": 33,
    "category": "Power Management (PMIC)",
    "subcategory": "DC-DC Converters",
    "datasheet": "https://www.ti.com/cn/lit/gpn/tps65261",
    "parts": {
      "symbol": "tps65261rhbr.kicad_sym",
      "footprint": "tps65261rhbr.kicad_mod",
      "model_3d": "tps65261rhbr-etched.glb",
      "model_3d_plain": "tps65261rhbr.glb",
      "model_3d_step": "tps65261rhbr-etched.step",
      "model_3d_step_plain": "tps65261rhbr.step",
      "lbr": "tps65261rhbr.lbr"
    },
    "distributor_links": {
      "lcsc": "C138722"
    },
    "pins": [
      {
        "number": "1",
        "name": "EN3",
        "type": "input",
        "description": "Enable pin for buck3; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V"
      },
      {
        "number": "2",
        "name": "PGOOD",
        "type": "output",
        "description": "Open-drain power good output; asserts low when any buck output is out of regulation (±2.5%), thermal shutdown active, overcurrent condition exists, or enable pin low; max sink 1mA at 0.4V"
      },
      {
        "number": "3",
        "name": "RESET",
        "type": "output",
        "description": "Open-drain power failure output signal; asserts low when VDIV input drops below 1.23V threshold for power failure detection; deglitch time 12-16 cycles"
      },
      {
        "number": "4",
        "name": "MODE",
        "type": "input",
        "description": "Mode select input; when high, enables automatic power-up/power-down sequencing based on EN1/EN2/EN3 states; when low, enables independent enable pin control; operating range -0.1V to 6.3V"
      },
      {
        "number": "5",
        "name": "V7V",
        "type": "power_out",
        "description": "Internal LDO output supplying gate drivers and internal logic; 6.3V typical (6.0V to 6.6V range), maximum current 175mA; requires 10µF ceramic capacitor to power ground"
      },
      {
        "number": "6",
        "name": "FB2",
        "type": "input",
        "description": "Feedback Kelvin sensing pin for buck2 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V"
      },
      {
        "number": "7",
        "name": "COMP2",
        "type": "output",
        "description": "Error amplifier output for buck2 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V"
      },
      {
        "number": "8",
        "name": "SS2",
        "type": "input",
        "description": "Soft-start and tracking input for buck2 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V"
      },
      {
        "number": "9",
        "name": "BST2",
        "type": "power_in",
        "description": "Bootstrap supply for buck2 high-side gate driver; connect 47nF ceramic capacitor between BST2 and LX2 pins; operating range -0.3V to 7V referenced to LX2"
      },
      {
        "number": "10",
        "name": "LX2",
        "type": "output",
        "description": "Buck2 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN2 voltage (maximum 18V); high di/dt node requiring careful PCB layout"
      },
      {
        "number": "11",
        "name": "PGND2",
        "type": "power_in",
        "description": "Buck2 power ground connection; connect as close as practical to negative terminal of PVIN2 input ceramic capacitor to minimize inductance"
      },
      {
        "number": "12",
        "name": "PVIN2",
        "type": "power_in",
        "description": "Buck2 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path"
      },
      {
        "number": "13",
        "name": "PVIN3",
        "type": "power_in",
        "description": "Buck3 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path"
      },
      {
        "number": "14",
        "name": "PGND3",
        "type": "power_in",
        "description": "Buck3 power ground connection; connect as close as practical to negative terminal of PVIN3 input ceramic capacitor to minimize inductance"
      },
      {
        "number": "15",
        "name": "LX3",
        "type": "output",
        "description": "Buck3 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN3 voltage (maximum 18V); high di/dt node requiring careful PCB layout"
      },
      {
        "number": "16",
        "name": "BST3",
        "type": "power_in",
        "description": "Bootstrap supply for buck3 high-side gate driver; connect 47nF ceramic capacitor between BST3 and LX3 pins; operating range -0.3V to 7V referenced to LX3"
      },
      {
        "number": "17",
        "name": "SS3",
        "type": "input",
        "description": "Soft-start and tracking input for buck3 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V"
      },
      {
        "number": "18",
        "name": "COMP3",
        "type": "output",
        "description": "Error amplifier output for buck3 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V"
      },
      {
        "number": "19",
        "name": "FB3",
        "type": "input",
        "description": "Feedback Kelvin sensing pin for buck3 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V"
      },
      {
        "number": "20",
        "name": "ROSC",
        "type": "input",
        "description": "Oscillator frequency programmable pin; connect external resistor to ground to set switching frequency from 250kHz to 2MHz; operating range -0.1V to 3V"
      },
      {
        "number": "21",
        "name": "AGND",
        "type": "power_in",
        "description": "Analog ground for buck controllers and analog signal circuits; route separately from high current power grounds to negative terminal of VIN bypass capacitor to minimize noise coupling"
      },
      {
        "number": "22",
        "name": "FB1",
        "type": "input",
        "description": "Feedback Kelvin sensing pin for buck1 output voltage regulation; connect to resistor divider network for output voltage setting; operating range -0.1V to 3V"
      },
      {
        "number": "23",
        "name": "COMP1",
        "type": "output",
        "description": "Error amplifier output for buck1 loop compensation; transconductance 300µS; connect series R and C for control loop compensation in peak current mode; operating range -0.1V to 3V"
      },
      {
        "number": "24",
        "name": "SS1",
        "type": "input",
        "description": "Soft-start and tracking input for buck1 with internal 5µA pullup current source; connect capacitor to ground to program soft-start time; operating range -0.1V to 3V"
      },
      {
        "number": "25",
        "name": "BST1",
        "type": "power_in",
        "description": "Bootstrap supply for buck1 high-side gate driver; connect 47nF ceramic capacitor between BST1 and LX1 pins; operating range -0.3V to 7V referenced to LX1"
      },
      {
        "number": "26",
        "name": "LX1",
        "type": "output",
        "description": "Buck1 switching node connected to external inductor and bootstrap capacitor; voltage swings from -0.8V (maximum withstand) to PVIN1 voltage (maximum 18V); high di/dt node requiring careful PCB layout and 180° phase shift from buck2/3 clocks"
      },
      {
        "number": "27",
        "name": "PGND1",
        "type": "power_in",
        "description": "Buck1 power ground connection; connect as close as practical to negative terminal of PVIN1 input ceramic capacitor to minimize inductance"
      },
      {
        "number": "28",
        "name": "PVIN1",
        "type": "power_in",
        "description": "Buck1 input power supply; operating range 4.5V to 18V; connect as close as practical to positive terminal of 10µF minimum input ceramic capacitor with clean voltage path"
      },
      {
        "number": "29",
        "name": "VIN",
        "type": "power_in",
        "description": "Buck controller power supply for internal logic and bias circuits; operating range 4.5V to 18V; UVLO thresholds: rising 4.25V typical, falling 3.75V typical, hysteresis 500mV"
      },
      {
        "number": "30",
        "name": "VDIV",
        "type": "input",
        "description": "Input voltage threshold for power failure detection; external resistor divider sets detection threshold to 1.23V typical; 1µA pullup current provides threshold hysteresis; operating range -0.1V to 6.3V"
      },
      {
        "number": "31",
        "name": "EN1",
        "type": "input",
        "description": "Enable pin for buck1; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V"
      },
      {
        "number": "32",
        "name": "EN2",
        "type": "input",
        "description": "Enable pin for buck2; float to enable or configure input undervoltage lockout with external resistor divider; operating range -0.1V to 6.3V, typical rising threshold 1.26V"
      },
      {
        "number": "33",
        "name": "Thermal Pad",
        "type": "passive",
        "description": "Exposed thermal pad for junction-to-board heat dissipation; no internal electrical wire bond to die; must be soldered to PCB ground plane for optimal thermal performance"
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.2",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.2",
        "primary_model": "claude-haiku-4-5-20251001",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "1/33 pins cited to the wrong page (name found elsewhere): ['33:Thermal Pad@p4']"
        ],
        "pages_sent": 48,
        "cost_usd": 0.5037,
        "at": "2026-09-23T08:28:44"
      },
      "datasheet": {
        "url": "https://www.ti.com/cn/lit/gpn/tps65261",
        "pages": 48,
        "sha256": "304396ee72bd117c",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 33,
        "described": 33,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "tps65261rhbr.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          5,
          5,
          0.875
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "5fa713ea46b36980895812ed853577889b7cb06d275041a39b99bc0be305dc79",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "tps65261rhbr-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          5,
          5,
          0.875
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "d4cea820db1de001b27be1111624ef76aadf168d2b687528394fcffc6579ab5c",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  },
  "metadata": {
    "specs": {
      "Manufacturer": "Texas Instruments",
      "Package": "VQFN-32-EP(5x5)",
      "Category": "Power Management (PMIC)",
      "Pins": "33"
    }
  },
  "variants": [],
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "tps65261rhbr"
  ],
  "discovery_pitch": "TPS65261RHBR (Texas Instruments) component page with datasheet-verified CAD.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "tps65261rhbr.kicad_sym",
    "tps65261rhbr.kicad_mod",
    "tps65261rhbr.glb",
    "tps65261rhbr.step",
    "tps65261rhbr.lbr",
    "docs/hero.png",
    "docs/tps65261rhbr-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "visibility": {
    "public": true
  },
  "updated_at": "2026-09-25T12:28:35.301Z"
}